Do-it-yourself framing of wallpaper joints with fabric edging. Wall decoration with fabric: step by step instructions

Decorating the walls with carpets and fabrics began many centuries ago. In the East, the tradition has survived to this day to hang a tapestry instead of partitions or paint the walls and paint them with gilding to imitate expensive embroidered material.

Drapery of walls with cloth adorned palaces in Greece and Rome. Even when the first paper tapestries appeared, the interior of the living room looked more luxurious with drapery with expensive fabrics. Wallpapers were glued by low-income people, the nobility and wealthy merchants preferred to drape the walls of the house with fabric.

Methods for decorating walls with canvas

long time upholstery with fabric was an expensive pleasure, accessible to a few. Gradually, the quality of the fabric changed; relatively inexpensive textiles appeared that met modern requirements interior. Kirill was interested in handsome wall material, suitable for any style and turning into a decor. Now my assistant wanted to know how to decorate the walls with fabric with his own hands. There are several technologies for finishing fabric on walls instead of wallpaper:

Drapery.
Wallpaper.
Seamless pasting under the rail.
Finishing with frames and frames.

By analogy with the walls, a stretch ceiling is made. The material must be prepared to size, create a pattern, wet and pull on the prepared frame, attach with clips around the perimeter and glue with moldings or ceiling plinth. Fabric wall decoration is better than paint:

Luxurious and unique look interior.
Suitable for any style.
Enhances the sound-absorbing effect of walls.
Keeps warm.
Quick change drapery, washable.
No need to level the walls and eliminate minor defects.
You can quickly glue the room without a single joint.

There are disadvantages, for example, the kitchen, with its dampness and smells, is not suitable for covering with absorbent material. Lining is possible in the dining area, but it is desirable that it be leather or upholstery impregnated protective compounds. Textured and loose material traps dust on its surface, absorbs dirt and moisture.

Drapery of walls with fabric (video)

Drapery - elegant walls of banquet halls

Decoration with soft falling waves is used in halls for celebrations and banquets, in living rooms, in preparation for the holiday. The photo shows a fabric decor that can be replaced quickly, repeating step by step simple steps with already prepared material. The fabric must be prepared:

Sew a solid canvas, the width is greater than the wall, since the finish should hang in waves.
Hem the top and bottom, maintaining the height of the partition.
Starch and smooth.
Fasten to a plank or bamboo cornice.

The advantage of the method is that you can quickly clad the walls, give the hall a decorative and holiday look. Then for a short time change the style and theme, decorate the room for the next celebration. The decoration does not need to be glued, it is enough to temporarily hang a soft drape material.

The advantage of drapery is the ability to quickly change the design, wash the fabric, use any finishing option in turn, inexpensively creating a stylish and elegant look. This option did not suit Kirill and me, since we are doing overhaul residential buildings and apartments.

Pasting with stripes according to the type of wallpaper

Instead of paper wallpaper, strips of fabric are glued to the wall. The texture is selected dense. The technology is partially different from the method of gluing with a roll finishing material. We had to stick fabric with a luxurious pattern in the living room with our own hands.

Before finishing, it is recommended to check a piece of fabric for shrinkage. I prefer to soak all the fabric that is taken for finishing. Industrial dust and oil from the equipment are washed from it. At the same time I dissolve salt in water, fix the paint, make brighter colors fabric base, I make the material non-combustible. The texture of the fabric is thickened. Now it fits better on the wall and attracts less dust. I had a large work table on which the fabric was smoothed before cutting. The stripes are narrow, so they were glued as ordinary wallpaper.

Cut into pieces with an allowance along the length. We checked the pattern match.
Glue was smeared on the wall, and starting from above, the panel was fixed.

The top edge can be fastened with carnations, then trimmed using lace or fringe.

Seamless pasting and the complexity of its implementation

The height of the children's wall made it possible to glue the fabric across. We did seamless coating walls.

We prepared the fabric, soaked it with salt and smoothed it well, rolled it up face inward.
Starting from the corner, the surface of the wall was smeared with casein glue, paying special attention to the perimeter.

Fixed the left end. Kirill unfolded the cloth and straightened it, I ironed it with a hot iron, melting and fixing the glue.
A hole was cut in place of the switch, and when they reached the opening, they cut the fabric in fact.

It’s hard for me alone to fit the walls and smooth them out. We dealt with my nephew quickly. But I already have experience, and several times finished the walls with fabric in this way.

Covering on and under the rail

The bedroom was next in line. We used the seamless method, fixing the viscose fabric wallpaper for the walls under the plank. The width of the cloth made it possible to cover the entire wall. I prepared the fabric and, with the help of my nephew, wound it into a roll. Then we acted according to the instructions.

The procedure can be seen in the video.

Secured the upper left corner of the fabric with a nail.
With the help of Cyril, he pulled the cloth at the top along the intended horizontal line and secured the right corner. The wall is long, so for convenience, I hammered a carnation in the center, so that it sags less. I usually don't do this on short spans.
The two of us were cramped, but comfortable. I tucked the fabric under the bar, Cyril twisted the screws. I made potam in advance, at a distance of 15 cm. We moved out of habit from left to right.
Finished at the top, moved down. They pulled and fixed the corners, then screwed the bar.
The corners were made simultaneously with the adjacent wall, securing 2 panels with one bar. It is not necessary to glue the textile material, just stretch it evenly.

To close the rail, you can stick a fabric border, put moldings on glue or decorate with braid, lace, paint. The idea of finishing can be any. The main thing is to do it carefully and in accordance with the style of the interior. In place of the socket and switch, I cut the fabric, made a hole with an allowance of 2 cm per side and fixed it around the perimeter with the same rail as the entire panel. The office needs silence for work, so the fabric was attached to a rail, laid thin layer foam rubber.

They marked out the level and plumb and attached the rack frame.
Then they began to cut and glue foam rubber on the wall.
They began to fit from above, by analogy with fastening under the rail.

You can pre-glue the frame from the rails to the size and sheathe them with a cloth. The insulating substrate is inserted into the frame. Sheathing is done imperceptibly with carnations with reverse side. Ready-made sections are mounted on the walls with glue. It remains to mask the joints of the frames.

Advice! The method of frame covering is convenient if it is necessary to frequently replace the lining with another one. Or update in places where the surface is quickly wiped and smeared, for example, in hallways and corridors.

Insulation with foam

A beautiful finish is obtained by creating a relief surface. The underlayment is installed on the frame. Attach to her thick layer foam rubber. Everything is covered with fabric. The fabric is cut out with an allowance of 10 - 15 cm. It is fixed with a stapler with back side. Then, on a convex surface, along the markings, a fabric with foam rubber breaks through to the base, resulting in a recess. Fragmented decoration perfectly decorates the walls at the head of the bed, zones soft corners in the living room.

Wall decoration with fabric – great way original design any residential area. You can cover the walls in the living room with an elegant fabric or a strict one in the office. Well, about decorating the walls of the bedroom with fabrics in pastel colors and there is no need to say - delicate material will decorate this room in the best possible way. To glue the fabric on the walls, you need to properly prepare the surfaces and read the step-by-step instructions.

If we talk about the design of the walls, it is worth noting that the fabric has some clear advantages over wallpaper or painting. Firstly, for such a finish, the walls do not require much preparation; secondly, if you are tired of your decorative decoration, then you can easily change it; and third, there's the added benefit of being able to reuse the removed fabric for other projects around the house if you decide to redo it.

In this article you will receive detailed information about drapery of walls with fabric with your own hands, you can see photos and videos.

Why cover the walls with fabric instead of wallpaper

There are at least five reasons why to cover walls with fabric:

Fabric is the perfect way to disguise not perfect walls; with its help, you can hide the fact that the walls have not been painted, sanded or puttied for years.
Cloth-covered walls will absorb sounds better than painted ones, especially if the surface is first laid with a layer of special padding.
Fabric on the wall instead of wallpaper (or paint) is also worth sticking because it is a portable investment. If you decide to move, you can take it with you.
Putting a special lining layer under the fabric, you can end up with the look of an upholstered, puffy wall.
Since you can unfold the fabric and view it over a large area, often by placing the fabric against the wall you can visually get a pretty good idea of how the fabric will look.

See how beautiful the fabric-covered walls are in these photos:

The choice of decorative fabric for wall decoration

To make it easier to work, opt for a lightweight fabric with a solid weave. Look for such a fabric, the pattern on which goes, as they say, “in structure”. However, if you like decorative fabric for walls slightly sloped, then when pasting, choose a design that does not require following the structure.

Before starting work, smooth out all wrinkles and folds on the fabric. When the entire room is already covered in fabric, you will almost certainly find yourself unable to match the pattern on last seam. Therefore, plan the beginning and end of work in such a way that this last butt joint falls on the most inconspicuous place. In particular, a door located near the corner of the room would be a good choice, because in this case only small plot right above the door.

Another option for wall drapery fabric- "bury" the mismatched seam in the corner, where it will be hidden by the furniture.

If you stretch or glue the fabric with beautiful pattern at certain intervals, then small bumps and surface irregularities will not be visible. For textured surfaces the best choice there will be a small decorative pattern of the fabric.

These photos show best fabrics for wall decoration:

Materials and fabric calculation for pasting walls

To decorate the walls with your own hands you will need:

Textile
Adhesive: Choose from either powdered cellulose or wheat paste or pre-mixed vinyl paste. Read the manufacturer's instructions and instructions, and look for an adhesive with an anti-mold component suitable for gluing fabrics.
liquid starch
Pieces of cloth or cellophane to protect the floor
Plumb or level
Paper clips (buttons) and hammer
Hard tape measure or meter
Wallpaper cutting knife
Paint or glue brushes or sponge
Wallpaper smoothing brush
Several clothespin rings from cornices

Before upholstering with fabric, you need to measure the width of the wall. Do not make adjustments for window and door openings. To determine how many panels you need, divide the total width by the available fabric width.

To determine the length of each panel when calculating the fabric, measure the height of the wall. Add 7.5-15 cm allowance.

To determine the total footage - multiply the number of panels by the length of each panel. Then divide that number by 100 cm to convert centimeters to meters.

Preparing walls for decorating with fabric

While fabric is a great way to cover less-than-perfect walls, there are still a few issues that shouldn't be ignored. You must fix all leaks, mold, and other plumbing or moisture problems on walls, air conditioners, or around windows. If such defects are not eliminated, the fabric will only emphasize them. Moreover, if the problems persist, they can damage the tissue itself.

Before you hang the fabric on the walls, do all the necessary painting work on the moldings, trim and windows before you start hanging the fabric. If you want, the moldings can be removed, painted and put back in place after the fabric has been placed on the walls. Remove switches, covers, old equipment for window curtains etc.

If you have chosen a light fabric, and the dark surface of the wall is visible through it, then the most easy way is to whitewash the walls.

Pasting, which does not require stitching, is one of the fastest methods of covering walls with fabric. The fabric is glued directly to the surface. Therefore, in order to achieve best result it is necessary that the walls are even, light in color and without cracks. Even on a lightly textured surface coated in this way, every bump will be visible.

Wash the walls. If they are stained, then wash them with a weak solution. detergent; if they are wallpapered, then vacuum thoroughly. If the walls are dark (and your fabric is transparent), then they need to be painted with white paint.

If you are covering new drywall walls, prime them. Otherwise, if you ever in the future begin to remove the fabric, then paper cover also come off the wall. The primer of the walls will also contribute to a good setting of the adhesive. This is especially important on new walls, as without primer protection, the adhesive will soak into the wall and ruin the work as a result.

Remove all switches and covers. Draw a vertical line on each wall to be covered following the instructions.

Check the color of the glue. Sometimes it is dark and can damage the color of the fabric. Always do a patch test to see if the adhesive works with your chosen fabric. Let the fabric dry and then carefully inspect it for any signs of color deterioration. If the fabric you choose has a repeating pattern, then you may need an extra amount for each panel, depending on how this repeating motif relates to the height of the wall.

See the photo on how to prepare the walls for drapery with fabric:

Do-it-yourself wall decoration: how to glue fabric correctly (with photo and video)

Do-it-yourself fitting and joining of fabric panels during drapery is done right on the wall. The technique is simple: slightly overlap the pattern; then, working on both fabric panels, cut off the overlap. Make sure the room is well lit, especially if you work at night, otherwise air bubbles will mysteriously appear on your walls during the day.

To properly stick the fabric on the wall, follow the step-by-step instructions below.

Step 1: Gluing the first panel

Cut the first panel equal to the height of the wall plus 10-15 cm. Using a brush or sponge, evenly spread the adhesive paste on the wall, covering the top third of the wall. Spread the adhesive over a slightly larger area than the width of the fabric. Align the pattern (not necessarily from the edge) with the vertical line and leave a margin of 5-7.5 cm at the top. If you are covering more than one wall, then place the first panel so that the left side wraps around the corner by 2.5-5 cm.
Using a smoothing brush, rectangle, or rag, smooth the fabric onto the wall. Start smoothing from the vertical line and work your way up. If the fabric is very heavy, use a few sharp studs or tacks to temporarily attach it along the top edge.
Gently lift and move the rest of the fabric away from the wall. Apply glue to the middle third of the wall. It's best to have someone hold the fabric while you glue the wall. If there is no one to help, then secure the fabric with a curtain pin or artist's paper clip and hook it to a nail driven into the top edge of the wall.
Smooth out the fabric over the area you glued, working from a vertical line down from the previously glued area.
Repeat the procedure (apply glue and smooth the fabric) on the bottom third of the wall.
Use the sharp blade of a craft knife to cut off the excess fabric along the top and bottom edges. If the fabric does not cut well, then wait until the glue dries. Since knife blades dull quickly, you will need to constantly change them.

These photos show the stages of decorating the walls with a do-it-yourself fabric:

Step 2: Stickering subsequent panels

Cut the fabric for next panel. Plan 2.5-5 cm per side margin for overlap and pattern alignment. Apply glue to the top third of the wall, including the bottom overlap (right margin) on the first panel. Smooth the fabric in place, making sure the pattern matches exactly under the overlay. Repeat the gluing and smoothing procedure on the rest of the panel.
Hold the straight edge firmly in the middle between the top and bottom overlap. Use a craft knife to cut through both layers of fabric (cut from top to bottom).
Remove the strips of fabric where the top overlap was. Then carefully separate the fabric from the wall and remove the overlap from below. Glue the second panel back in place and smooth it again. If necessary, use a brush to add a little more glue to the wall along the seam.
Cut off the top and bottom edges as shown in Step 1, step 6.
Repeat the procedure for gluing, smoothing and cutting with the rest of the panels.
Check pasted walls for air bubbles: Poke a needle through such areas or make a small cut there and smooth the fabric on the wall again. If there are many small air bubbles under the fabric, finish one wall, then smear with a thin layer of liquid starch. This kind of sanding will help you remove bubbles and act as a protective layer against dirt.

Advice. If the edges of the fabric move away from the wall, carefully tear the fabric away from the wall, smear the wall with glue and, after gluing the fabric again, smooth it on the wall. You can also apply a thin layer of glue to this area. When the fabric softens again, the adhesive will soak through it into the wall. Smooth this area with a rag or brush.

Advice. If the fabric is very heavy, clothespins or staples may not be able to hold it. In this case, it is better to take large safety pins.

Step-by-step wall decoration with fabric is shown in this video:

Pasting walls with fabric requires preliminary preparation of the surface of the walls. They must be carefully cleaned, puttied, primed. The surface must be absolutely even, smooth and dry. You should also prepare the fabric. To do this, you need to cut off a small piece of fabric, measure its size, then wet it and dry it. After complete drying given piece tissue should be measured again. If the fabric has noticeably shrunk, the entire canvas that will be attached to the wall must first be wetted, dried and ironed. If the fabric did not shrink, or the shrinkage was insignificant, then decoration is not necessary: due to a slight shrinkage, the fabric will stretch better on the wall surface.

Before pasting the walls with a cloth, cut the cloth, as well as the wallpaper, into strips with a length equal to the height of the wall, make a few centimeters of stock. After that, for each wall you need to sew a separate canvas. To do this, strips of fabric are sewn in width into one canvas, equal to the width of the wall (plus twenty centimeters of stock). It is desirable to iron the resulting canvases and roll them into rolls along the height of the walls.

As a rule, gluing the fabric on the wall starts from the corner. To do this, a fabric is applied to the surface of the wall, then a roll of fabric is taken, applied to the wall and, smoothing it well, carefully glue a strip of fabric along the entire height of the wall. So that when smoothing the fabric does not move out, its edges are temporarily fixed with a wooden lath, slightly driving nails into the wall at a short distance (10-20 cm) from each other. Thus, the canvas is consistently glued over the entire area of \u200b\u200bthe wall. Wooden slats are removed only after the glue is completely dry.

More the easy way wall decoration with fabric is upholstery or close-fitting. This method is attractive in that before covering the walls with fabric, the surface of the walls does not have to be leveled. The web of fabric is attached to wooden slats with nails. Wooden slats are fixed to the ceiling and floor, while, if possible, they are embedded in plaster so that the slats protrude several millimeters above the level of the plaster.

Strips of fabric, as in pasting, are sewn into one canvas, equal in area to the wall. The finished canvas, stretching well, is nailed to the fixed wooden slats with nails, the distance between which should not be more than 10 centimeters. The bottom of the fabric is attached with a plinth, and the top is fixed ceiling strip. Covering the walls with fabric can be done in another way. In this case, the web of fabric is stretched over wooden frame, the area of which is similar to the area of \u200b\u200bthe wall. The frame is attached to the wall, fixing it with nails to wooden slats pre-stuffed around the perimeter of the walls.

Wall decoration with fabric can look so chic that it becomes difficult to understand why our compatriots have not yet made this solution the most common among all others. You can even make such repairs with your own hands, and most importantly, the design will be completely atypical! In a way, the finished result will be something like a wallpaper, but it is, figuratively speaking, like a 3D movie with glasses compared to the usual 2D.

Wall decor with fabric for many is a real novelty, so you should carefully consider whether it is worth taking on such a design. Like any other design decision, it has both positive and negative sides.

Advantages

Decorating walls with fabric is:

Unique chic, underlined by soft features - no other material will give anything even similar.
The special comfort of the room, in which all the bumps and sharp corners are smoothed out.
Lack of preliminary preparation of walls that do not need to be specially leveled, unless it is a question of gluing fabric instead of wallpaper.
Protection from most mechanical damage - the material simply stretches under load, without forming breaks or cracks.
Increased, in comparison with paper wallpaper, sound insulation.
Material with textured surface can replace decorative plaster without losing the rest of its positive qualities.
Wall fabrics are available in a wide variety, which allows you not only to choose from a variety of finishes, but also to combine the color and texture of the walls with curtains or linens.

Textile wall decoration is elegant and cozy, however, when deciding on such a finish, you should know all the pitfalls

Difficulties

There is nothing absolutely perfect in the world yet, so wall decoration with fabric also has a couple of dubious points that claim to be shortcomings:

The fabric on the walls is able to collect on itself great amount dust, which is especially important in big cities and close to trails. Developers have already created materials that repel dirt, but the price of them remains quite high.
Textiles are not among the most durable materials. More precisely, it can be preserved for a long time, but it appearance quickly loses its original freshness. No matter how hard the manufacturers try, the material is still quite easy to stain or wipe to such an extent that it becomes noticeable. As a way out, it is not recommended to attach the fabric to the walls in narrow passages, and ideally, it is generally better to fix it in such a way that it is possible to remove and wash it.

Material selection

If, despite all the difficulties, a decision was made in favor of textile design, it remains only to decide on a specific type of material. Theoretically, there are no restrictions on the choice at all, and the owner of the premises is free to choose what he likes. If we focus on practicality and durability, then the fabric used for wall decoration should be strong and elastic so that there is no constant need to replace damaged material. If you buy fabric for furniture upholstery, you will definitely not be mistaken, because according to performance it is approximately the same. If the material was originally intended for finishing, then surely the manufacturer has already properly processed it, and it will be more convenient to work with it.

It should be noted that when focusing on do-it-yourself repairs, special attention should be paid to the choice of material, because the method of fastening depends on it, and they differ in complexity.

Methods for attaching fabric to walls

Each type of textile has its own characteristics, which makes the craftsmen fasten the fabric in different ways. Deviations from the norm are possible, but most often it is better to stick suede, velvet and velor, drapery of walls with fabric suggests thinness and lightness of the material, and so on.

pasting

In this variant, the result obtained, perhaps, will most closely resemble expensive wallpapers. Pasting walls with fabric is relevant literally everywhere, even aprons for kitchens are made using this technique, just the material on top is either varnished or covered with glass. Any towels, tablecloths, curtains and other items sewn from the same textile allow you to create a harmony in the design of the room.

The process of gluing walls with fabric is somewhat similar to gluing ordinary wallpaper, but it is more complicated and requires more accuracy.

Sticking the fabric directly to the walls is perhaps the most difficult of all the other options. Since we are talking about an analogy with ordinary wallpaper, then the wall, firstly, must be properly prepared - cleaned, puttied, primed. The gluing procedure itself also requires great care - in general, it will be better to trust the professionals.

If, nevertheless, it is decided to carry out repairs with your own hands, then first you need to check the degree of shrinkage of the material. To do this, a small piece is cut off, soaked in water, then dried. The dimensions of the piece are measured before and after the procedure, and if there is not much difference, then you can start gluing. If shrinkage is obvious to the naked eye, then you will have to wet and dry the entire roll. Material preparation also includes pre-ironing.

Unlike wallpaper, the fabric is not glued in strips, but immediately on the entire wall - for this, the strips pre-cut with a margin are sewn together. To keep the seams as small as possible, it is better to take a wide cut. Before the final gluing, the seams are once again carefully ironed. Although such a sheet is usually attached only at the edges, at least two people will be required for this procedure. It is desirable to start from the side, continue from above. If the material is heavy, on top of it, already glued, small slats are carefully stuffed, which are not removed until the glue dries. The surface of the wall in the process is carefully smoothed out with a roller. At the end of the work, the excess fabric at the edges is carefully cut off.

Upholstery

Only at first glance, upholstery with fabric seems to be a simple task, which anyone who has ever held a hammer can do with their own hands. The problem is that for the perfect evenness of the resulting woven surface, the upholstery of the walls with fabric is carried out not on the walls themselves, but on top special frame, by analogy with stretch ceilings or drywall. To cope with such a task on your own is quite difficult, but possible.

Wall upholstery with fabric construction companies, who, however, are also ready to help those customers who want to try to do the work with their own hands. You can buy fastener parts and a seamless fabric that does not need stitching from them. This method of fastening is good because there is no need for preliminary preparation walls, and the void can be filled with sound or heat insulation, and electrical wiring can also be hidden there. A ready-made mounting system, purchased from a specialized store, makes it relatively easy to remove installed textiles for replacement or washing.

Wall upholstery with fabric using removable wall structures allows you to remove soft panels for cleaning procedures

upholstery

Draping the walls with fabric is the easiest way for those who want to get off with a minimum of effort. Such a finish usually does not imply a full-fledged fastening of the fabric to the walls over the entire surface; it falls freely, in folds. Wall drapery, which is always performed with folds, involves only fixing textiles on a horizontal bar hidden under the ceiling.

The cut with which it is planned to drape the wall must be much wider than it, otherwise the folds will not work.

Fabric in the form of an original exception can be attached immediately on four sides of the cut. Frames made of wood, plastic or metal can act as a basis. In this case, the folds must be thought out in advance, it is better to immediately highlight them with small seams, otherwise it is not possible to predict exactly how the roll will develop after the walls are draped.

Wall drapery with fabric is used to create either an oriental or European aristocratic style. This design is appropriate in living rooms or living rooms, as well as in public institutions.

The fabric on the walls instead of wallpaper will give them a special gloss and solidity. paper wallpaper today is a relic of the past.

You can choose any type of fabric: linen, velvet, textiles, silk. Before you make a choice in favor of fabric wallpaper, consider all their advantages and disadvantages.

Like any wallpaper, fabric has its pros and cons:

The fabric resists mechanical damage well, it just stretches without leaving dents and scratches on the wall.
Such wallpapers give the room comfort, smooth out all the notches and sharp corners.

The same fabric can be used for walls, when decorating window curtains, pillows, tablecloths and then the room will turn out in a single unique style.
Before upholstery of a room with a fabric, it is unnecessary special training walls, the fabric will hide all the bumps.

Note. Fabric instead of wallpaper increases the sound insulation of the room, and also helps to retain heat. A room with fabric wallpaper will always be warm and quiet.

Negative sides of fabric instead of wallpaper

Everyone has it finishing material has its positive, but also negative sides.

Fabric wallpaper does not differ from other raw materials:

The appearance of the fabric on the walls quickly fades and loses its appearance, so you will have to change the fabric upholstery on the walls often, or they can be removed and washed.
Gathered on fabric a large number of dust which is difficult and almost impossible to eliminate. Fabric wallpapers have already been developed that repel dust, but their price is very high and many cannot afford them. Taking care of such a room will be much more difficult and you need to be prepared for this.

Interiors with different types fabrics in the photo:

How to choose the right fabric

If you have weighed the pros and cons and still decided to use fabric instead of wallpaper, then you need to decide on a specific material:

You can choose any fabric that you like, but you still need to pay attention to its practicality and wear resistance.
For example, if you take a fabric that is used to upholster furniture, then it will be practical and durable.
Choose fabrics that are sold in specialized stores for decoration, they were originally processed and impregnated with special substances.

When choosing a fabric, please note that the fabric of the wallpaper is attached to the wall in different ways, it all depends on what type of fabric you have chosen!

Choose a fabric holder that allows you to easily remove the material for cleaning or replacement!

So:

Such models will always look beautiful, and not stretched on the wall.

In the kitchen, it is better not to use fabric trim, as it tends to absorb odors.

If you want to improve the sound insulation of the room due to the fabric, then pick up heavy jacquard materials or wallpaper under denim. You also need to leave airspace between the wall and the raw material.

For pasting walls in too wet room, you should pay attention to synthetic fabrics that are pre-treated with a moisture-repellent composition.

Note. The fabric can decorate not the whole room, but only some part of the wall. So the room will not be oversaturated and, in turn, this will give it comfort.

Mounting methods

Let's look at ways to attach fabric to walls instead of wallpaper, as well as instructions for each method:

Methods	Carrying out work	Adviсe
	This option is similar to pasting walls with ordinary wallpaper, only as a result we get the look of expensive walls. Fabric wallpaper pasted over even work surface() in the kitchen, only then it will be necessary to additionally open it with varnish or close it with a protective glass. Fabric-like wallpaper is glued in the same way as ordinary wallpaper, but it will take more time and accuracy. To paste over a wall with a cloth, you first need to prepare the wall, namely putty and primer. Pasting the walls with such a fabric is difficult and laborious process Therefore, it is better to turn to specialists in this field. But if you want to do everything with your own hands, then first take a small, measured piece of fabric that you will peck at the wall and glue to the wall, after the fabric dries, measure with a ruler. Thus, you will know the degree of shrinkage of the fabric. If there is no difference before and after the procedure, then you can immediately start sizing. If the fabric has shrunk significantly, then you need to dampen the entire fabric in the roll and let it dry.	The fabric under the wallpaper is glued immediately to the entire perimeter of the wall, and not like ordinary wallpaper in stripes. Therefore, the fabric will need to be carefully sewn and the seams ironed well. Fabric wallpapers are glued only in cuts, but you cannot do without an assistant. It is best to start the cage from the side, and then the top. If you took a heavy fabric, then first glue it, and then stuff the slats upstairs, and remove them after the fabric has completely dried. This is necessary in order for the fabric to hold well. During pasting, the fabric on the wall must be leveled with a roller. At the end, the excess fabric on the sides must be carefully trimmed. Depending on the fabric, we select the glue for pasting, since different glue is needed for each type of fabric.
	At first glance, upholstery with fabric seems like an easy and simple task, but it is far from being the case. The fabric is nailed directly to the wall, but to a special frame, which is nailed in advance along the perimeter of the wall. This procedure is similar to screwing drywall (see) or stretch ceilings. With a strong desire, you can cope with such a difficult task and do everything yourself.	This method is good because it does not need pretreatment and wall preparation. If desired, the void between the fabric and the wall can be filled with terma or sound insulation. The fabric from the special frame will be easy to remove to clean.
	It is extremely rare to drape walls with fabric, but they resort to it to decorate a banquet hall. The fabric on the walls instead of wallpaper in this case is not attached around the entire perimeter of the wall, but simply involuntarily falls in folds from top to bottom, something like curtains only for walls. The fabric is attached taking into account the numerous folds under the ceiling on a special bar.	The piece of fabric should be much wider than the wall itself to create folds. Keep this in mind when buying fabric for drapery! Walls decorated with drapery give the room a special coziness and create a romantic atmosphere. The fabric is easy to remove and wash or clean and replace.

In the photo you can see how the walls are draped with fabric:

Before you decide to “dress” your walls in fabric, we recommend that you watch the video in this article and get to know the information in more detail.

Categories

Popular