How to glue vinyl wallpaper: features and recommendations. How to glue vinyl wallpaper (48 photos): gluing paper-based canvases and heavy coatings

Vinyl is far from the latest innovations, therefore, there are a lot of tips and recommendations on the question: how to glue vinyl wallpapers and also what kind of glue to use. At the beginning of their existence, they were called "washable wallpapers" because the vinyl base is durable and resistant to water. Vinyl wallpaper has a number of advantages over paper wallpaper, for example, later you can safely repaint them.

How to glue vinyl wallpaper? Vinyl wallpapers are completely different from wallpapers that have a paper backing. There are many nuances in their sticking, they should be taken into account. Since vinyl wallpaper has two layers ( upper layer made of polyvinyl chloride, and the bottom layer of interlining or paper), they are glued to a special glue, it is designed for heavy wallpaper. By the way, these wallpapers are good because they let air through well, and from many different structures, you can choose the one that is perfect for your room.

Required Tools

So, how to glue vinyl wallpaper and where to start? Prepare everything in advance necessary tools, it will greatly speed up the pace of your work.

You will need:

  • roller, in order to roll their seams;
  • special brush for priming and applying glue;
  • brush for small areas on the wallpaper;
  • spatula for smoothing wallpaper;
  • sponge (soft) or cotton cloth to remove excess glue;
  • scissors;
  • roulette;
  • a small spatula can be very useful, it will be convenient for it to press the wallpaper in the corners, as well as straighten it in narrow uncomfortable places;
  • stationery knife;
  • ruler;
  • level and paper tape.

Back to index

Preparing the base for gluing vinyl wallpaper

First of all, you need to carefully prepare the walls: get rid of the old coating, whether it be plaster, paint or wallpaper; clear the base greasy spots if there are cracks, they need to be puttied (the putty should dry well before you move on to the next step); walls must be even and strong. You can check the strength of the walls as follows: cut off a small piece of adhesive tape, stick it on the wall, if after you pull it sharply, paint or other wall covering remains on the wrong side, then the base requires careful preparation before starting work.

Next up is the primer. To do this, spread cold water(following the instructions) dry glue, which is designed for vinyl wallpaper, then apply to the walls. Wait until the soil is completely dry, it will take about 3-4 hours. Then treat the walls with a fungicidal composition that will prevent the appearance of mold under the canvases. Waiting for the composition to dry, prepare a thread with a weight tied to it, use it to draw a vertical line along the wall.

So it will be convenient for you to navigate when you glue the first wallpaper sheet. Before you start gluing the canvas, turn off the electricity in order to remove all sockets and switches from the walls.

What else should you know?

  1. What glue to use.
  2. How to glue.

It is important to note that when sticking vinyl wallpaper, it is imperative to close all windows, fans and air conditioners should not be turned on (there should be no drafts in the room).

To make it easier for you to get rid of old wallpaper, you need to wet the walls with water. Then, after waiting a little, with a spatula, you can easily clean the surface.

Back to index

How to glue vinyl wallpaper?

First, prepare the vinyl wallpaper for gluing. Cut them in strips along the height of the wall, leave allowances of about 10 cm on the strips. If there is a pattern on the panel you have chosen, you need to select the segments so that the pattern matches. Place the fabric in a pile pattern side down.

Back to index

Instructions for preparing glue

The glue is kneaded in a cup of suitable size with the proportion of water you need. Pour the glue slowly while stirring to avoid the formation of lumps. Then the glue should be infused for 5-10 minutes, after repeated mixing, you can start gluing.
What glue to glue vinyl wallpaper? What kind of glue to glue the wallpaper of your choice, the store consultant can advise.

A selection of glue is an important detail, since the texture of this material can be of several types. And the result of your work depends on the answer to the question of what glue to glue vinyl sheets with. The edges will have to be given special attention, there should not be a single unsmeared area. Therefore, smear them with a brush, and for the rest of the area you can use a roller. Glue is applied to desired area on the wall, in some cases on wallpaper (carefully read the instructions on the package with wallpaper). Apply glue evenly thin layer, then fold the wallpaper so that their bases match. Leave them in this position for 5 minutes.
Press the fabrics with a roller or brush (the bristles of which should be short), iron all seams properly.

Back to index

How to glue heavy vinyl wallpaper

So, you have already decided which glue to glue, then you are interested in the question: how to glue vinyl wallpaper correctly. To glue this type of canvas you need at least two people. You need to start from the corner of the wall opposite the window and most correctly from the ceiling, it is convenient to do this from a stepladder, at this time you need to hold the bottom edge. The edge of the wallpaper should coincide with the line you previously drew. Gently press the panel against the wall and brush out (from top to bottom) all air bubbles. Glue must not come into contact with outside wallpaper, if you can’t avoid it, gently wipe the protruding glue with a cotton cloth. Do not stretch the width of the vinyl wallpaper during installation, otherwise it may shrink, resulting in empty spaces.

How to trim the edges? Excess material is cut along the ruler with a knife (the knife must be sharp). In the skirting area, leave the bottom edge with a margin of 5 mm. It must be inserted between the wall and the baseboard, but for a more accurate result, remove the baseboard before starting work.

Vinyl wallpaper is a very common material for decorative finishes walls. But before describing the technology of their gluing, it is necessary to consider the varieties of this finishing material.

There are two main categories:

Paper based vinyl wallpaper has two sides. One side is paper, it is to her that the material is glued to the surface of the wall. The second side is polyvinyl chloride, it serves as a decorative finish for the room.

Non-woven vinyl wallpapers have non-woven backing instead of the paper side. The other side, as in the first case, is made of polyvinyl chloride.

What premises are intended for

Vinyl wallpapers are very resistant to moisture, in addition, they can be washed. One wet cleaning, and there will be no dirt.

Vinyl wallpaper is suitable for rooms where there is a high probability of occurrence high humidity. They can be applied in in public places where there is a risk of contamination.

There are several types of materials:

  • without embossing;
  • with hot stamping.

Hot embossed wallpaper

Embossed wallpapers, in turn, are divided into several types:

  • chemical embossing (inhibition);
  • compact vinyl;
  • silkscreen;
  • heavy vinyl.

Heavy vinyl is perfect solution for rooms where uneven walls. Such wallpapers perfectly hide all the defects and emphasize the dignity of the room.

Heavy vinyl is suitable for hallways and commercial spaces because these are the areas where wall defects are most likely to show up. Compact vinyl is also great for such needs. Many varieties of compact vinyl have a texture natural materials and hide defects.

In addition to the fact that with the use of such wallpapers the walls will acquire an aesthetic appearance, they will also have a unique finish.

Silkscreen is better for rooms. It is smooth, aesthetic and light. Before pasting, you just need to remember that it is better to process the walls for such wallpapers properly. If irregularities remain on the surface, then silk-screen printing will not hide them, but only emphasize them.

Inhibited wallpapers are perfect for both corridors and commercial premises. They can be glued in the apartment, but in order to keep the surface of the walls of the rooms clean, a simple silk-screen printing is enough. Distinctive feature wallpaper with chemical embossing is resistance to moisture and various radiations.

Wallpaper without embossing

Vinyl wallpaper without embossing has a uniform structure. Their top layer consists of polyvinyl chloride without a pattern. These materials have their own merit. Firstly, they perfectly hide even quite serious surface defects. Secondly, such a coating looks very intriguing and even gives a certain charm. In addition, such materials perfectly cope with aggressive influences. They can be washed and wiped with a damp cloth. They are not afraid of moisture at all, although you should not experiment with their wear resistance.

Wallpaper without embossing can look strict, so with their help you can create the appropriate atmosphere in office space. Today, however, many offices have switched to more technological Decoration Materials. However, plain vinyl allows you to create a solid environment.

Stages of work


Adhesive selection

Before repair, you need to choose glue. The master can purchase either a composition of a universal type, or a special glue for paper or non-woven varieties of wallpaper. Other compounds will not work, because vinyl materials have their own specifics.

It is better to purchase high-quality glue and not be afraid for the consequences. It is better to buy compositions in trusted stores to avoid fakes.

Sticking to the ceiling

When choosing wallpaper, you need to take into account their properties. It is important to remember that wallpaper for the ceiling must have a slippery surface for a good joint between the seams and actually stick to the ceiling. For these purposes, vinyl wallpaper is best suited.

Secondly, you need to prepare workplace. Safe movement under the ceiling itself should be ensured. To do this, racks are assembled at the same level with each other so that there are no obstacles, and the risk of injury during work is minimized.

In order for the wallpaper to adhere well to the ceiling, and the seams are firmly connected to each other, the glue must be in consistency like thick sour cream. For these purposes, Quelyd glue (Kelid) is best suited.

You will need the following tools:

  • construction knife;
  • metal tape measure or centimeter;
  • container for diluting glue;
  • roller;
  • the ruler is larger than the width of the wallpaper to cut a smooth edge;
  • metal spatula;
  • brush for applying glue;
  • plastic spatula;
  • a plastic small roller for pressing down at the junction of the wallpaper.

When all the right materials and tools at hand, you can start gluing.

First, glue is applied to the ceiling using a roller. Then, unwinding the roll, apply its edge to the ceiling smeared with glue, with one hand continue to unwind the roll further. At the same time, with the other hand, smooth the canvas with a spatula. At the end, the sheet can be cut off, leaving a small margin, and finally leveled with a ruler or a metal spatula.

The first strip of wallpaper is pasted without much difficulty, since it does not fit with anything. If the wallpaper needs to be driven under a baguette, then a slight overlap is made, and when the canvas is well fixed on the ceiling, it is carefully cut to fit the ruler. You need to try to ensure that the first strip of wallpaper is glued evenly.

Subsequent canvases should be glued in the same way, only with the difference that the joints must be carefully connected to each other, and also pressed down well with a plastic roller so that over time the wallpaper does not peel off and the seam between the canvases is not noticeable.

Meter wallpaper has the following advantages:

  • Firstly, money is saved, since the cost of one roll of wallpaper with a width of 1 m is lower than the cost of two rolls of a regular width of 53 cm.
  • Secondly, you can significantly save time and effort when gluing canvases, since fewer canvases are required for pasting walls.
  • And, finally, thirdly, the number of joints between wallpaper sheets is reduced, and thus there are practically no seams, which in general decorates the interior.

It should be remembered about the shortcomings when using meter wallpaper.

  • It is required to prepare surfaces with high quality so that uneven walls do not affect what the joint between the canvases will be, even if the work is carried out with wallpaper of a single color that does not require the selection of a pattern.
  • Also when working with meter wallpaper need helper while wallpaper standard width 53 cm can be glued by yourself.
  • If the room is non-standard, it may be difficult to fit the canvases due to the lack of wallpaper length.

The following tools are required:

  • glue;
  • primer;
  • construction knife;
  • scissors;
  • long ruler (meter);
  • rubber roller;
  • plastic roller for joints;
  • wide brush;
  • plumb;
  • pencil;
  • clean rag.

Before starting work, you need to prepare the surface of the walls. First, a primer or more liquid wallpaper paste is applied to the walls (you can use the cheapest one). It is necessary to treat the walls with a primer in order to improve the properties of the adhesive and ensure a snug fit of the canvas to the wall.

Styrofoam cornices must be fixed before the pasting process begins.

First you need to measure a distance of 1 m long, and then draw a vertical line in this place using a plumb line, a long ruler and a pencil.

Then the height of the wall is measured from the curb or ceiling to the floor, it is advisable to add 5-10 cm as a margin. To find out the number of sheets, the length of the roll (indicated on the package) is divided by the measurement obtained. If the wallpaper contains an image, then when cutting the canvases, you must remember that you will have to combine the pattern.

The technology of pasting walls with meter wallpaper

  • Pre-prepared glue is applied to the surface of the walls.
  • The first sheet of wallpaper is adjusted to the marked line and the height of the ceiling, without protruding beyond the line. Only then can the canvas be glued to the wall.
  • Then it is necessary to squeeze out air from under the wallpaper with smoothing movements using a rubber roller.
  • Next, using a construction knife or a metal spatula, cut off excess wallpaper. Wet wallpaper must be allowed to dry and only then trimmed, otherwise they may tear.

How to dock

  • If the wall surfaces are even, then joining the next canvas is not difficult.
  • When gluing the second canvas, it is necessary to join it with the previous one along the entire length, leveling the wallpaper and pushing out the remaining glue.
  • To make the joint even, you can not pull the wallpaper with a roller. The joint will disperse immediately after the canvases dry.

Work in hard-to-reach places

  • When pasting the corner, an overlap of 2–3 cm is made on the wall to be pasted. extra wallpaper cut to the desired size with a construction knife.
  • When pasting the wall under the batteries or above the door, you need to measure required distance and cut the desired length of the strip, without disturbing the construction of the pattern when joining.

Vinyl wallpaper in the interior

Vinyl wallpaper will help create a unique style in the room. With their help, you can decorate any interior. This is possible due to the fact that there are a great many types and colors of these wallpapers.

For example, in order to give the atmosphere an exclusivity and individuality, you can use strict plain vinyl, which immediately captivates with its mystery. In the rooms, wallpaper with floral embossing is used to add luxury to the decor. Vinyl materials can be used even in the nursery. The range allows you to choose materials for any premises. In this case, such wallpaper can always be cleaned. Therefore, they will serve for a long time, if only they are glued with high quality.

A photo

Video: instructions for sticking vinyl wallpaper

When it comes to decorating walls in rooms where there is a high risk of contamination, then you can’t imagine anything better than vinyl wallpaper. It is this material that allows you to make wallpaper with a dense washable decorative coating, which proved to be at its best in areas such as hallways, and even bathrooms. In this master class from the site site, we will study the question of how to properly glue vinyl wallpaper, and also draw your attention to all the intricacies of this wall cladding technology.

How to glue vinyl wallpaper with your own hands

How to glue vinyl wallpaper: choose glue

The main property of vinyl wallpaper, which has a direct impact on the technology of their gluing, is a relatively large weight. Vinyl wallpapers belong to the class of heavy wallpapers, and for sticking them you will need a one with a high setting ability. In principle, this is not a problem, and practically does not affect the process itself. You can buy this glue anywhere. hardware store- it is called "Vinyl" or "Glue for vinyl wallpaper."

So, with the question of how to glue vinyl wallpaper, we figured out, it remains only to solve the question of how to properly prepare it. It's not difficult - we take a clean bucket and fill it up to half warm water. We arm ourselves with a small stick and, intensively stirring the liquid, pour the contents of the package with glue into it. You need to pour it quickly and evenly - so that you have time to stir it.

After the last granules of glue are in the water, set the bucket aside for five minutes to completely swell the glue. After this time, we perform repeated stirring and see what we got - if the glue resembles thick jelly in its consistency, this is normal. If it turns out jelly, then add water and mix well. That's all! The glue is ready to go.

How to prepare glue for vinyl wallpaper photo

Vinyl wallpaper on non-woven fabric: do-it-yourself gluing technology

I want to make a point right now. There are several types of vinyl wallpaper - depending on the base, they can be made both on non-woven and paper-based. From this, the technology of their gluing changes a little - vinyl wallpaper for walls on a non-woven base does not need to be smeared with glue. But sticking paper-based wallpaper without this step is impossible. But let's get back to business and thoroughly study the question of how to glue vinyl wallpaper?

If we are talking about paper-based vinyl wallpaper or non-woven wallpaper with a selection of a pattern, then they need to be cut into the necessary stripes. Everything is simple here - we measure the height of the walls, roll out the wallpaper on the floor and cut off the strip of the required length with a sharp construction knife. All subsequent strips are cut relative to the first one in compliance with the drawing step.

The next step is to smear the wallpaper with glue and fold each strip separately so that the glue does not smear front side. This is necessary so that the base of the wallpaper is thoroughly saturated with glue. You can spread many strips at once - then you will not have to be distracted by this work. If we are talking about non-woven vinyl wallpaper, then this step is not needed - you don’t need to smear them with glue at all.

While the wallpaper is saturated with glue, we smear the wall - here such an approach as with wallpaper is not suitable. Do not smear the entire wall with glue at once, as it tends to dry out. Therefore, we smear the wall with only one canvas.

How to glue vinyl wallpaper with your own hands photo

Let's start gluing the first strip. In order for it to lie flat, you can pre-draw a vertical line on the wall using a level, relative to which to stick the first strip.

Vinyl wallpapering: leveling for the first wallpaper strip

We start gluing from above. We adjust the top of the canvas under the baguettes and thoroughly smooth the wallpaper canvas and at the same time align it with respect to the drawn strip.

How to glue vinyl wallpaper photo

You need to level it from the middle to the edges - for this purpose, either a plastic spatula or a dense roller is used.

How to smooth wallpaper on the wall photo

Difficulties with gluing the first strip, as a rule, do not arise. At the end of the process, the excess wallpaper, both at the bottom and at the top, is cut off. sharp knife.

How to trim the top of vinyl wallpaper photo

Gluing the second and all subsequent strips looks more complicated - here you will have to clearly fit the canvases to each other so that there is no gap between them. In this respect, gluing vinyl is much easier - they slide well on a surface smeared with glue. You just have to move them or move them away from the neighboring lane. The seam needs to be given special attention - it must not only be carefully adjusted, but also properly glued. In principle, nothing supernatural needs to be done if the canvases are pasted evenly without folds.

How to glue the joints of vinyl wallpaper photo

The main problem that arises when pasting walls with vinyl wallpaper is the corners. The overlap of the canvas cannot be joined here, since the glue practically does not stick to the vinyl. The question of how to glue the corners with vinyl wallpaper is solved in only one way - by turning the canvas. You can, of course, try to make a joint in the corner of the room, but such numbers work only in the case of ideal. This is how the question of how to properly glue vinyl wallpaper is solved. Difficulties can arise only in the process of fitting butt-to-butt canvases. In all other respects they are in no way different from all others. We can even say that this is not the worst option in the work - it is much more difficult to stick or with silk-screen printing. Author of the article Alexander Kulikov

Currently, almost all wallpapers are made from vinyl. This synthetic material has proven itself: it is durable, resistant to damage, non-hygroscopic, easy to clean. Vinyl coverings can be used for more than ten years without losing excellent appearance and aesthetics.

Types of wallpaper with vinyl coating

To properly paste the wallpaper, you need to know everything about them. Vinyl flooring can be of two types:

  • on a paper backing;
  • based on non-woven fabric.

The first option is more affordable, the paper base has no other advantages. The non-woven substrate has several characteristics:

  • transparency;
  • elasticity;
  • tensile strength;
  • good adhesion to many wall materials.

Vinyl wallpaper on a non-woven basis consists of three layers: vinyl, opaque dense synthetic material, interlining. This makes them thick and dense, the structure allows you to mask small cracks and uneven walls. The coating on non-woven backing will not tear so quickly in the corners due to cracks, because the fabric is elastic and can stretch.

Given the characteristics of the material, it is necessary to decide how to glue non-woven vinyl wallpaper. This can be done in several ways.

Standard pasting method

To glue non-woven wallpaper, you need minimum set tools:

  • glue;
  • container for mixing glue;
  • wide brush or pile roller;
  • rubber spatula;
  • long metal ruler;
  • sharp knife and scissors.

Preparatory work

An important factor during installation is the right adhesive. The composition is chosen in accordance with the type of wallpaper. Non-woven fabrics are heavy, so the glue for them should be thicker. The dry mixture is poured into a container with water, stirring constantly. After five minutes, the composition is ready for use.

Equally important is the condition of the surface of the walls and ceiling. At the preparation stage, it is necessary to remove the old coating, it is moistened with water or a weak adhesive solution. Swollen wallpaper is removed with a metal spatula.

The walls and ceiling are inspected for cracks, irregularities. All defects are repaired with starting putty. After drying, it is polished sandpaper. It is better to process all the walls with a thin layer finishing putty- The smoother the surface to be glued, the neater the new coating will look.

Any moisture-absorbing wall material (concrete, plaster, drywall) must be coated with a primer.

Advice! As a primer, you can use the same glue that will stick the wallpaper.

It is dissolved in accordance with the instructions and applied to the walls with a fur roller. The surface must dry well before subsequent gluing.

If wallpaper is selected for decoration light shades, it is better to paint the primer with a color scheme of the corresponding color. Non-woven vinyl coatings are transparent. Unlike paper, stains can appear on them.

The prepared room is left until the soil is completely dry.

Installation of non-woven wallpaper

The standard procedure for pasting surfaces with vinyl wallpaper involves the arrangement of strips without overlap - it is correct to glue such canvases end-to-end. They do it because thick material, overlaps will be too noticeable. Thanks to this feature, you can start work from anywhere in the room.

This will avoid possible irregularities and joints of the canvas in a conspicuous place.

At the zero point, it is necessary to draw a vertical line along which the first strip will be aligned. This can be done with a plumb line or building level. The width of the outlined strip should be 1.5-2 cm less than the width of the roll. This edge must be brought to a corner.

The wall is carefully coated with glue. Another feature of the non-woven substrate is that it does not need to be treated with glue - just apply it to the wall. It is important to avoid gaps; in the corners and under the ceiling, the glue is applied in a thick layer with a small brush.

Important! When the repair time fell on the summer heat, it is better to glue not only the wall, but also the wallpaper with glue.

While the strip is measured and cut, the wall may dry out due to the high temperature.

A piece of the desired length is cut from the roll (2-5 cm are added to the height of the walls). The upper edge of the canvas is aligned with the line under the ceiling and leveled relative to the vertical line. rubber spatula or wallpaper roller press the strip in the center, moving from top to bottom.

Now you need to expel excess glue and air. To do this, make movements with a spatula from the center to the edges. Excess glue is removed with a clean cloth.

Advice! If the edges do not fit snugly against the wall, you can stick under the seam thin paper or special paper tape for wallpaper. So the canvas will stick more reliably, the seams will be less noticeable.

At the ceiling, the wallpaper is cut with a sharp knife. First, they are pressed against the corner with a metal spatula, without removing it, a straight line is drawn with a knife. If a plinth is installed below, the lower edges can be cut with scissors. All the same, the plinth will close the cut line.

The wallpaper is pressed into the vertical corner with a plastic spatula, preventing the accumulation of glue and air bubbles there.

Cut off the next strip from the roll. If the wallpaper is with a pattern, it is more convenient to work with several rolls at once - this will reduce material consumption. The second strip must be glued, focusing on the edge of the previous one. The seam should be invisible, so the canvases are placed as close to each other as possible, but avoiding overlap. Non-woven wallpaper is very elastic, it will not be difficult to pull them up a couple of millimeters.

If the strip lay crooked, it can be torn off the wall and pasted again. However, do not abuse this, with each separation the glue will shift, forming clots.

Corner wrapping

Correctly sticking wallpaper in the corners is quite difficult - it will take skill:


Alternative method

Not certain way how to install wallpaper correctly. For the above option, you need horizontal surface for cutting fabrics. Given the height of the ceilings, you need long table or a specially constructed platform.

Home repair is a troublesome business, especially when it comes to interior decoration that sets the tone for the entire interior. The presence of errors can spoil the entire design of the room. We will help you avoid them by analyzing in detail how to glue vinyl wallpaper on the ceiling and walls.

General provisions

First, let's pay a little attention to the chosen material. Why exactly vinyl wallpaper, what is special about them? Everything will become quite clear after reviewing their qualitative characteristics.

Advantages

The products in question are a non-woven or paper base coated with a layer of vinyl.

This structure provides them with many advantages:

  • moisture resistance. Excellent quality, which is unusual for most other types of wallpaper. But vinyl not only resists moisture quite reliably, but is also able to withstand wet cleaning using household chemicals and even painting.

  • Wide range of possible models . In addition to a stunning selection of diverse ornaments and colors, there are also textured and silkscreen designs.

  • High resistance to mechanical damage, ultraviolet radiation and even temperature extremes. That is, if you are opposite the south window, get a cat and begin to arrange long-term ventilation in winter, they will still retain their original appearance.
  • Long service life , which reaches ten years.
  • Simple sticking instructions, which we will analyze further in all the subtleties.
  • Acceptable price. The whole set of strength characteristics is quite affordable for the budget of the average man in the street.

Flaw

The only thing that can happen unpleasant after applying the wallpaper in question is the presence bad smell the first two months. But this is subject to the purchase of cheap samples from an unknown manufacturer. Qualitative models do not have this effect.

Tip: if you still managed to stick foul-smelling canvases, and even airing does not help, then it is recommended to paint them with acrylic paint.
The polymer layer will block the contact of vinyl and air, eliminating the spread of odor.

Application technology

First of all, you should prepare everything necessary for the implementation of finishing work.

Tools and materials

For work you will need:

  • Velor roller. Simplifies the processing of canvases and walls.

  • Brush. Allows you to qualitatively cover hard-to-reach places with glue.

  • A clean bucket for diluting the adhesive mixture.

  • Special bath with ribbed surface.

  • Stepladder - so that you can get to the top of the wall and ceiling.

Tip: choose a ladder that has a shelf on top.
Then you will have where to put the container with glue.

  • Metal or plastic. It makes cutting fabric much easier.

  • Roulette for all necessary measurements.

  • Stationery knife for cutting wallpaper.

  • Brush for smoothing products on the wall.

Tip: before gluing heavy vinyl wallpaper, be sure to make sure that the prepared brush is sufficiently stiff.
Because soft bristles will simply crumple on dense canvases and will not cope with their task.

  • A clean rag to remove spilled drops of glue on the front side of the finish.

In addition to tools, you need to take care directly of the materials themselves:

  1. Wallpaper choose in accordance with the rest of the interior of the room and its functionality. products designed for painting are better suited, and for the living room, for example, silk-screen samples. The color scheme is also very important and can have a significant impact on the feel of the occupants, visually expand and narrow the room.

  1. How to determine when buying which adhesive is best for vinyl wallpaper? There are no secrets in this and you should not invent something new. Just read the attached instructions for the glue, and check with the seller for details.

  1. Putty. It will be needed if in the wall after removal old finish large cracks and significant damage will be found.

Preparatory work

Before sticking vinyl wallpaper, you must carefully prepare the surface of the wall.

And although such large-scale work with perfect alignment, as in the case of using paint, are not required, something still needs to be done:

  1. Removing the old lining:
    • We wash off the paint with a special chemical composition.
    • We knock down the tile with a perforator.
    • We remove the wallpaper with a sharp metal spatula, after wetting it with water.

  1. We putty possible cracks and noticeable irregularities.

  1. We prime the wall. Do not refuse this step, even if it seems overhead and superfluous to you. Primer creates polymer layer, which increases adhesion, protects the surface from physical influences and reduces its porosity.

Sticking

Now let's figure out how to stick vinyl wallpaper:

  1. We dilute the adhesive mixture with water according to the instructions indicated on the package.

  1. We measure the wall, add a few centimeters and mark the resulting length on the unrolled roll.
  2. cut off right size according to the labels.

  1. Apply glue to back side canvases. It is noteworthy that if products with a non-woven base are used, then this step is not needed.

  1. Next, apply the adhesive to the wall.

  1. We apply the canvas to the surface and smooth it with a brush, removing all the air from under it.

  1. In the process, you will definitely come across the following question: how to glue vinyl wallpaper in the corners? The fact is that the corners in the room are almost never quite even, because of which you will not be able to make even joints there. Therefore, the canvas should be applied so that it covers the problem area and goes to the adjacent wall by at least 10 cm.

Conclusion

We have examined how vinyl wallpaper is glued. The process is not complicated at all, but requires accuracy and attention. Stick to all the above recommendations, and you will succeed.

The video in this article will provide Additional information. Good luck wallpapering!