Car alarm antenna unit scher khan logicar a. We determine the quality and capabilities of Sherkhan car alarms. Designations of buttons and symbols on the keychain

Car "signaling" Sherkhan Logicar 1 is the flagship product of the manufacturer, which has extensive functionality, including the option feedback with vehicle. Also, thanks to the unique signal encoding, security system has a high resistance to burglary.

[ Hide ]

Specifications

Car alarm Sherkhan Logicar 1 has the ability to auto start engine both instantly, by command from the communicator, and delayed, by timer. The notification of the car owner about the state of the vehicle and the occurrence of alarm situations is carried out by means of a remote control. For this, vibration or sound signals are used.

The parameters that this system has:

• protection of impulse signals from interception is carried out by means of a special author's encoding Magic Code PRO 2;
• in alert mode, the range of the key fob will be up to 1.5 km, and when sending commands, the range of the device will decrease to 500 meters;
• ability to activate and deactivate guard mode without using a communicator, using a special password;
• using a code for staged disarming;
• the presence of three types alarms- sound, optical (using optics), as well as the transmission of impulses over a radio channel;
• data is sent at an operating frequency of 433 MHz;
• safety elements, resistor devices, transistors, and diodes are used to protect power lines;
• the microprocessor module is powered from the on-board network at 9-18 volts;
• the value of current consumption by the alarm in armed mode will be from 20 to 35 mA;
• performance of all functions by the system is possible at air temperatures from -40 to +85 degrees;
• AAA batteries are used to power the main remote control, CR2016 batteries are used for the additional one;
• battery life in the main communicator is about 4 months, in the additional - up to three years.

Equipment

System delivery set Scher Khan includes the following elements:

1. Service user manual for system maintenance and configuration. The documentation allows you to properly install, connect and program the anti-theft system.
2. Wiring diagrams for car alarms.
3. The main microprocessor device.
4. Communicator with liquid crystal display. Designed for adjustment technical parameters and alarm functionality. The presence of the screen allows two-way communication with complex.
5. Spare pager, no display. Its main feature and difference from the main key fob is the absence of feedback and an alert system.
6. Alarm installation kit, which includes power cables and pads.
7. Shock and sensitivity sensor. Designed to determine any shocks and other impacts on the car body. In accordance with the signals sent from the sensor, the information is fed to the main communicator and the control unit. If the impact is severe, the protection function is activated.
8. Jack service key used to activate emergency mode alarms. Equipped with a cable with a plug for connection.
9. Transceiver module with connected block.
10. Relay for blocking the power unit.
11. Limit switch for mounting on the hood.
12. Siren with block for connection.
13. Sticker for fixing the antenna module on the glass.

For full protection before installing the Sherkhan Logicar 1 alarm system, you must additionally purchase Limit switches for doors and trunk.

Channel "Arnage" spoke in detail about the configuration anti-theft complex Logicar 1.

Main functions

Options available this model alarms:

• the ability to synchronize the readings of communicators linked to the microprocessor module;
• option to control a second vehicle if it has a similar model anti-theft system;
• key fob screen backlight;
• alarm option;
• time display in online mode;
• blocking buttons on the key fob;
• option to protect the car with the engine running;
• switching on the security mode without sound and alarm signals;
• the presence of five configurable channels for controlling additional electrical equipment;
• the ability to program the type of relay blocking the power unit;
• option to select the number of door lock control signals and their duration;
• closing and opening doors when the ignition system is activated and turned off;
• the ability to monitor the intensity of the motor in accordance with the signals of the tachometer;
• option to automatically activate the protection mode;
• the "Panic" function, which allows you to turn on the operation of alarms and lighting devices on command from the remote control.

Functions regarding automatic engine start:

• the possibility of using this option on cars with manual or automatic transmission;
• setting up a remote start of the internal combustion engine (internal combustion engine) on vehicles equipped with a Start / Stop button to start the engine;
• the ability to use the function in cars equipped with diesel or gasoline power units;
• engine start time setting option.

Advantages and disadvantages

The advantages that this Sherkhan model has:

1. Extensive functionality. The alarm is equipped with many options that not only protect the car, but also simplify its use: synchronization of communicators, silent security mode, delayed engine start.
2. High reliability. In fact, it is almost impossible to hack Sherkhan Logicar 1 signaling by intercepting the code due to the author's signal encoding system.
3. Affordable price. The cost of the alarm ranges from 3800 to 5000 rubles, depending on the region of sale.
4. Decent build quality. All elements and devices that are included in the system kit are supplied in a protective rugged case.
5. No false positives. At correct setting sensitivity of the shock sensor, the consumer will not encounter the activation of the alarm mode for no reason.

Disadvantages that the alarm may have:

1. Incorrect operation of the system, "glitches" are possible. Consumers usually encounter such a problem as a result of installation errors. In particular, we are talking about incorrect wiring.
2. In accordance with the reviews, another drawback is the low efficiency of the alarm when negative temperatures. In frost, the system may execute commands with a delay, sometimes Logicar 1 does not respond to signals from the key fob.

How to install an alarm?

Alarm installation can be done in a garage. You must first prepare a set of tools for installation, as well as disconnect the battery.

To install an anti-theft system, you need to have:

• multimeter for measuring voltage and determining breaks (short circuits) in electrical circuits;
• Screwdriver Set;
• socket wrench set;
• soldering iron;
• wire stripping tool;
• mounting blades for interior disassembly;
• black electrical tape;
• foam rubber;
• double sided tape;
• plastic clamps for wiring.

Wiring diagram

To connect the security complex, the following wiring diagram is used:

General Map for connecting signaling elements (fragment 1) General map for connecting signaling elements (fragment 2) General map for connecting signaling elements (fragment 3) General map for connecting signaling elements (fragment 4)

Step-by-step instruction

The installation procedure is as follows:

1. The microprocessor module is installed in a hidden way in the car. It can be placed behind the instrument cluster, glove box or under the dash. It is desirable that in order to gain access to the device, you have to disassemble the trim in the cabin, this will prevent the car from being stolen quickly. To fix it, double-sided tape or plastic ties are used.
2. The transceiver module is mounted in the upper corner of the windshield or rear window. It is important that the distance from the antenna to metal objects was at least 5 cm, this will avoid interference. Before installation, the glass surface must be cleaned. If the installation is carried out in winter, then its temperature can be at least 10 degrees Celsius. The laying of the wire from the antenna to the microprocessor module is carried out under decorative cladding cabin, during installation it is necessary to ensure that the cable is not pinched.
3. The LED indicator is mounted in the corner of the front glass. First, its surface must be cleaned and degreased. You can embed a diode indicator into the dashboard, then first you need to make a hole in it for installing a light bulb.
4. The siren is located under the hood of the car, in the most protected from external influence from under the bottom of the car. Do not install the siren near heating units and moving parts. The horn of the device is recommended to be placed down to prevent the formation of moisture inside.
5. The hood limit switch is mounted on metal surface which is closest to the body. There must be no accumulation of moisture at the installation site. When the hood is closed, the sensor is protected by a rubber seal.
6. The shock sensor is fixed in the car using two bolts. During installation, it must be taken into account that the user must have access to the controller in order to change the sensitivity parameter. The sensor is equipped with two regulators. The first determines the sensitivity of the warning zone, and the second determines the alarm zone. For fixing, it is better to choose the central part of the body so that the device determines physical influences from all sides of the body.
7. If additional controllers are used, their installation is carried out taking into account the manufacturer's recommendations. For example, an engine temperature sensor must be installed in the cooling system line.
8. After installing all the elements, they are connected to the control unit. The wires are laid under the decorative lining of the car interior.

User manual

Before using the key fob, a working power source must be installed in the device. The battery is inserted into a special compartment hidden under the back cover of the communicator. Polarity must be taken into account when installing.

Designations of buttons and symbols on the key fob

All indicator designations and button numbers on the transmitter:

Indicator	Description
	Indicator of operation of the transmitter of the key fob-communicator and the presence of communication from the key fob to the processor unit.
	Feedback signal presence indicator.
	Battery discharge indicator of the keyfob-communicator and Battery Save Mode.
	Indicator of time, battery voltage of the key fob-communicator and additional textual information.
	Valet mode indicator.
	Guard mode status indicator. Locking and unlocking indicator in Valet mode.
	Siren off indicator.
	Shock sensor off indicator.
	Vibration call indicator.
	Power indicator automatic control central ignition switch.
	Alarm indicator.
	The indicator of inclusion of automatic start of the engine on the timer.
	Indicator remote start additional channels.
	Turbo indicator.
	Passive arming indicator.
	The indicator of transition to a mode of work with the second car.
	Open door indicator.
	Hood open indicator.
	Trunk open indicator.
	An indicator of an alarm caused by a shock sensor.
	Indicator of the completed start reservation and alarm caused by the ignition being turned on.
	Engine running indicator.
	Light signaling indicator.

Designation of button numbers on the key fob

Pager Programming

Without programming the communicator, setting up the alarm functions of Sherkhan Logicar 1 will be impossible.

To bind a new remote, do the following:

1. The car alarm security mode is disabled. The ignition in the car must be turned off.
2. The button on the LED housing is pressed, it must be clamped for two seconds. The car's headlights should then flash.
3. Within the next five seconds, the button is pressed again. If a password has been set to control the alarm, then the headlights of the car should blink twice. If there is a PIN code, the blinking will be single.
4. If a password is used, it is entered. If you don't have a PIN, you don't need to do anything.
5. After five seconds, the LED will turn on continuously. This indicates that the car alarm has entered the communicator binding menu. No more than three remote controls can be registered in the memory of the Sherkhan Logicar 1 microprocessor signaling module.
6. During the next 5 seconds, the first keyfob button is pressed. To program other devices, follow the same steps.

How to program autorun?

To set up automatic engine start, use the programming tables given in the manual.

1. In accordance with the table, it is necessary to transfer function 2-13 to the third position. This will allow the motorist to change the assignment of programmable channels to control the starter device and the ignition system.
2. Using the communicator, it is necessary to set the time period from the moment the starter is turned on to the time the power unit starts. In accordance with the tabular data, the maximum is set close value for function 2-20. If tuning is carried out on a vehicle with a diesel engine, then the time period for option 2-21 is indicated. If the vehicle has a Start/Stop button, the values ​​of function 2-25 are adjusted. On machines with a turbocharged engine, change option 2-24.
3. Then you need to adjust the parameters that provide smooth operation functions. This refers to the warm-up time of the power unit, as well as the operation of the headlights in automatic start mode. Additionally, you need to set the number of cycles to start the motor in remote mode, it is recommended to select no more than four. If the engine will start on a timer, you must select a time interval.
4. After the time is set, you need to “click” on button 4 ten times.
5. At the end of setting all values ​​and functions, you must simultaneously press the second and fourth keys of the key fob. The timer option will be enabled. To disable the automatic start function, follow the same steps.

Programming table

Menu of programmable functions [buttons (II+IV)]:

Anton Kovalev spoke about the operation of the autorun option on the example of the Logicar 2 model, in the case of the Logicar 1 alarm, the implementation principle will be similar.

Operating modes

The Logicar 1 system can operate in different modes:

1. The first button of the keyfob is used to activate the guard, and the second key is used to turn it off. After turning off protection mode, all door locks open, the starter mechanism and the power unit are unlocked. If the alarm sounds six times with a siren when the guard is deactivated, this indicates that the alarm was working. In the case of five signals, the system turned on as a result of receiving an impulse from the sensitivity sensor.
2. Activation of the search for a vehicle in the parking lot is performed by the first button. When setting up the option, car protection must be turned off. The machine's lighting devices will blink five times, and the communicator will play a melodious signal.
3. To open the luggage compartment, the third key fob button is pressed for 2 seconds. When the security is on, the mode will be turned off automatically, but the locks on the doors will not open. If necessary, the consumer can set this option to unlock the door locks.
4. To check the status car alarm the fourth key is used, it is pressed briefly. After the “click”, the display of the communicator should display data on the operation of the anti-theft system.
5. The "Panic" mode is activated by pressing and holding the 1st keyfob button for two seconds. To disable the option, you must "click" on the first or second key.
6. Activation and deactivation of alarms on command is performed by pressing buttons 1 and 2 on the key fob.
7. Switching on and off the Valet service mode is performed by simultaneously “clicking” on the keys 1 and 3. This function is used if the car is left for repair at the service station.
8. To enable and disable the sensitivity controller remotely, press buttons 1 and 4 simultaneously.
9. Activation and deactivation of the key lock mode on the key fob is performed by briefly pressing the third and fourth keys. When the function is enabled, the communicator will emit a short pulse, and its display will show the inscription “Hold”.
10. Switching on the security mode with the engine running is done by pressing the first button on the remote control. The ignition must be on, and all doors, as well as the hood and luggage compartment, must be locked. The door locks will be locked, the alarm will activate the security mode. If the protection is disabled or the siren sounds, the anti-theft system will automatically stop the engine and block its operation.

Setting the "Pit-stop" mode, in which you can turn on the guard with the engine running, when there is no key in the ignition, is performed as follows:

1. When the power unit is running, the transmission selector is set to the neutral speed position. In case of automatic boxes The gear lever must be set to Park.
2. The hand brake lever is raised.
3. The second key of the communicator is pressed for two seconds. The transmitter will emit a melodious signal, the vehicle lights should blink once. The ignition support option will be activated, and the headlights of the car will blink at a frequency of 1 time in five seconds.
4. Then the key in the lock scrolls to the off position to turn off the ignition. The power unit will continue to function for a certain time, pre-configured by the consumer.

A detailed description of the Sherkhan Logicar 1 keyfob options is presented by the Buyer's Notes channel.

Possible malfunctions

Problems specific to this car alarm model:

1. The key fob does not perform its functions, does not send commands. The cause of the problem may be the discharge of batteries, a mechanical failure of the device, or a software malfunction. If the power supply fails, the battery must be replaced. If the problem is the negative impact of moisture on the device, but the key fob must be disassembled and dried so that no traces of water remain on its board. If the remote control is damaged, its internal components are changed by soldering.
2. The wires connected to the alarm are damaged. With prolonged use of the security complex, wear of the conductors is possible, in particular, if they were laid next to moving elements and assemblies. To find a damaged cable, you must use a multimeter. After replacing the wires, it is recommended to wrap them with electrical tape to ensure they additional protection from wear.
3. One of the elements of the security complex failed. We are talking about the transceiver module, sensitivity controller, microprocessor unit. A detailed check of each device will be required, first of all, it is necessary to verify the integrity of the contacts through which they are connected. If the control unit has failed as a result of exposure to moisture, then its housing must be disassembled and dried by disconnecting its parts. Malfunctions of a software nature of the microprocessor can be solved by flashing, which is best left to specialists.
4. Appeared false positives, the alarm is activated for no reason. Such a problem is usually associated with an incorrect setting of the sensitivity of the shock controller. To eliminate the malfunction, this operating parameter must be reduced by using the sensor adjustment. It is not recommended to set the sensitivity value to the minimum.

Download free installation and operating instructions for the Sherkhan Logicar 1 alarm in PDF format

You can download service manuals for installing and configuring the security complex using the links:

How much does the Sherkhan Logicar 1 alarm cost and its installation?

The cost of the anti-theft system and its installation:

Video

The Scherkhanalarm channel spoke in detail about the security options of the Logicar 1 anti-theft system.

Car alarm Sherkhan Logicar 1 is considered one of the most reliable products from the manufacturer. With the help of two-way communication, the user will be alerted to any problems related to the car. Of the minuses of the complex, consumers highlight the complexity of installing the system.

[ Hide ]

Equipment

First, let's take a look at the components that are included in the car alarm kit:

1. User's book for installation. The documentation describes in detail how to install and connect the elements of the complex to the vehicle's on-board network.
2. Instructions for use. Allows you to configure and correctly program the main Scher options Khan Logicar.
3. Map of installation and connection.
4. main control module.
5. Pager. Used to control and adjust basic parameters and functions. With the help of the key fob, not only the alarms are turned on and off, but the complex is also configured.
6. Spare communicator. The device does not have a screen, but it also allows you to perform basic functions.
7. Mounting kit. Includes power wires with connectors.
8. Impact controller. It is used to register any physical impact on the car body and send information about it to a pager.
9. , designed to switch the system to the service mode. Equipped with a wire with a connector for connection.
10. Transceiver with connected plug.
11. Motor blocking relay.
12. One limit switch. Can be used for installation on the hood or tailgate.
13. Siren.
14. Sticker for mounting the transceiver on glass.

Technical properties

Properties car alarm Logicar 1:

• the “signaling” uses Magic Code PRO 2 technology, which allows to provide protection against interception of signals;
• the range of the remote control with the control device is up to 1500 meters in alert mode and up to 500 meters when sending commands;
• if the communicator is lost, the disarming procedure can be carried out using a special password;
• another code can be used to phase out the protection mode;
• the turbocharged mode can be configured so that during its operation the cooling time of the motor turbine changes.

The Auto Project video shows how you can hack the Sherkhan anti-theft complex.

Functionality Logicar 1

The main function of the alarm is to ensure the safety of the machine.

The system is equipped with the ability to start the car engine at a distance, the features of which are as follows:

• the use of this option is allowed on cars with manual transmission and automatic transmission, as well as on cars equipped with ignition with a Start / Stop key;
• this option can be used on machines with engines powered by diesel fuel or gasoline;
• you can set the start time of the internal combustion engine;
• it is possible to implement the option in the time interval every two, four or eight hours;
• you can start the internal combustion engine remotely by sending a command from the communicator.

Separately, we should talk about the functions of the pager with the screen:

• a message from the central module is sent to the pager in confirmation of the completed or failed options;
• if you have a second car, then the pager can be tied to its alarm, of course, when Sherkhan Logicar 1 is used on it;
• the pager screen displays the operating time of the internal combustion engine when the Turbo mode is activated, the Pit Stop function or remote start;
• communicator displays talkback signal indication;
• the temperature level in the car interior is displayed on the screen;
• the communicator can inform the car owner about changes in the car's power supply voltage, the diagnostic command is sent from the pager;
• the key fob allows you to determine the level of charge in the power source of the gadget;
• vibration alert option;
• The power saving mode will prevent the rapid discharge of the power source in the key fob.

Anton Kovalev showed how the Logicar model works on Renault Duster.

Advantages and disadvantages

Advantages of Sherkhan Logicar 1:

1. Wide functionality. The model has the necessary options to protect the car.
2. Reliability. As a result of installation, the consumer may not worry about the safety of the vehicle.
3. Low price. The cost of an anti-theft agent is from 3800 to 5000 rubles on average.
4. High build quality. All components of Sherkhan Logicar 1 are made in a durable case, which makes it possible to exclude their breakage as a result of falls or other physical impacts.

The disadvantages include the fact that, judging by the feedback from consumers, malfunctions may occur in the operation of the Sherkhan Logicar 1 alarm. Usually this drawback is due to the fact that during installation the requirements that the car must meet were not met.

How to install an alarm?

Installation is done like this:

1. The battery turns off. This is required to deactivate the voltage in the on-board network. Otherwise, during installation, you can accidentally close the contacts on one of the devices to ground, which will lead to a breakdown. To disconnect voltage from the battery, disconnect the cables with terminals.
2. Install the processor module in the passenger compartment. Choose a place for installation so that the device is inaccessible to a criminal when a car is broken into. It is best to install the device behind the control panel, this place is the most difficult to access, and besides, you will have to disassemble the center console. Remove the trim of the steering wheel and dashboard, disconnect the plugs with wires from the device. Determine free place behind the tidy and install the block in it. To eliminate the negative impact of vibrations on the device while driving, the module can be wrapped with foam rubber.
3. At the next stage, a siren is installed, it must be placed under the hood. Choose a location that will be least exposed to moisture and high temperatures. It is not allowed to mount the device near the cylinder block, subsequently the siren will melt and will not be able to perform its functions.
4. The shock sensor is mounted in the cabin. It cannot be placed under the bottom, the controller will quickly fail as a result of exposure to dirt and moisture. Install the sensor in the center of the body, this will allow it to effectively determine the impact on the car from all sides. You can place the device on the partition that separates the engine compartment and the passenger compartment.
5. Install the antenna on the inside windshield. It is possible to mount the transceiver under the glass on the dashboard, but it is desirable that this element be located as high as possible in the cabin. This will ensure efficient reception and transmission of signals. Please note that the quality of the pulses is affected by the presence of metal objects near the antenna. It is desirable that they are located no closer than 4 cm from the device.
6. Install the limit switch on the hood. After installation, bring the connection cable to the switch into the car interior.
7. Perform the service key setting. The Valet button must be masked, since it can be used to turn off Sherkhan Logicar 1. You can hide the key in a harness with standard wiring.

User manual

Below we will analyze the main nuances from the technical manual for using and configuring Sherkhan Logicar 1.

Designations of buttons and symbols on the keychain

The designation of the buttons and indicators of the Sherkhan Logicar 1 key fob is presented below.

Purpose of indicators on the communicator Purpose of the buttons on the communicator

Communicator Binding

Pager programming:

1. Turn off protective mode Sherkhan Logicar 1. With the ignition off, press the key located on the body of the diode element, the button is held for two seconds. Light fixtures machines should blink once.
2. Then, within five seconds, you need to click on the button again. The lights will blink twice if no password is used. If there is a code, then the lighting devices will blink once.
3. If you are using a password, then you must enter its value. The lights in the car will flash twice.
4. After five seconds, the diode bulb will burn without interruption. This suggests that the consumer can prescribe a new remote control. In total, Sherkhan Logicar 1 allows you to bind no more than three communicators.
5. Within five seconds, click on the first key of the communicator. The procedure for binding other remotes is repeated similarly.

Autostart Programming

How to enable autoplay:

1. According to the settings table, move option 2-13 to position 3. Thanks to this, you can change the assignment of channels for controlling the starter mechanism and ignition.
2. Using the remote control, set the time interval from the moment the starter is activated until the moment the internal combustion engine starts. It is recommended to set the nearest parameter from the table for option 2-20. If you are setting up the function for a car with a diesel engine, you must specify the time interval for 2-21. When setting the parameter on machines equipped with a start/stop ignition system, it is necessary to adjust option 2-25. If the vehicle is equipped with a turbocharged unit, then function 2-24 should be adjusted.
3. The next step is to configure several parameters that will provide correct work functions. We are talking about the warm-up time of the engine and the operation of the light devices of the machine during automatic start. You also need to set the activation interval for the timer option and make adjustments to the number of cycles engine start. If the engine is not running, then it makes no sense to discharge the battery by endless attempts to start it. Typically, experts set up four start cycles.
4. After setting the parameters, click on the buttons 2 and 4 of the communicator at the same time. This will activate the timer.
5. After setting the time, press the fourth key ten times in a row. This will allow you to adjust the settings. When the settings are defined, you need to click on the keys 2 and 4. This will activate the option.

Repeat the setup steps in Sherkhan Logicar 1 to disable the autorun option.

Modes

Description of the modes in which Sherkhan Logicar 1 can operate:

1. The protection is activated by pressing the first key; to deactivate, use the button 2 of the communicator. When disconnected, the locks on the doors will open, the starter mechanism and motor will be unlocked. If the siren gave six signals during the shutdown, this indicates that an alarm was triggered. Its operation is due to the activation of the limit switches on the doors or the hood. When the siren emitted five beeps when turned off, the system was triggered by the command of the shock controller. If the siren gave four signals, this indicates that the warning zone of the sensitivity controller has been triggered.
2. To activate the search for a car in the parking lot, you must click on the communicator button 1 when the protection function is enabled. The car's lights will flash five times and the pager will beep once.
3. To open the tailgate, hold down the key 3 of the communicator for two seconds. If the armed mode is activated, it will automatically turn off, but the door locks will not be unlocked. You can configure the opening of the trunk with unlocking the locks on the doors.
4. The status check mode of Sherkhan Logicar 1 is launched by a short click on the button 4. Information about the status of the complex will be displayed on the pager screen.
5. Activation of the Panic mode is carried out by holding the first key of the communicator for two seconds. To disable the function, the first or second button is pressed.
6. To enable or disable siren alarms, you can hold down the first and second buttons of the communicator.

Photo gallery "Tuning tables"

Main malfunctions

Errors and problems that the user may encounter:

1. Communicator failure. The failure of the pager may be due to the discharge of power sources, so when the first problems appear in the transmission of commands, check the battery. If she sat down, she needs to be changed. Open the back cover and replace the power supply, observing the polarity. If the problem is mechanical damage to the communicator or exposure to moisture, you need to disassemble the case and assess the condition of the board. Damaged components such as capacitors and contacts must be replaced and resoldered, and contact elements must be cleaned in case of oxidation.
2. Wire damage. During prolonged use, electrical circuits can be damaged, especially if they were laid in the area of ​​\u200b\u200bmoving parts of the body. Diagnosis will require the help of an electrician. If you have experience and skills, you can use a tester to find damaged wires. Electrical circuits must be replaced regardless of the nature of the damage.
3. Failure of one of the components. It can be a shock sensor, a processor module, an antenna adapter. It is necessary to diagnose the contacts on these devices, the oxidized connectors are cleaned. For more serious problems, detailed diagnostics of the devices will be required. Malfunctions of the control unit can be eliminated independently if they are related to the hardware. When water gets on the device, it must be disassembled and dried. But in the case of software failures, it is recommended to entrust troubleshooting to experts, since it may be necessary to flash the unit.
4. False positives. This problem is due to errors made when adjusting the impact controller. In accordance with the instructions and the installation diagram, it is necessary to adjust the sensor. It is required to reduce the sensitivity so that the controller does not work from passing cars. But the sensitivity threshold cannot be set to a minimum, since this will lead to the fact that Sherkhan Logicar 1 will not record the impact on the car body at all.

The Scher Khan Logicar A security system is designed to ensure the safety of the vehicle. It supports two-way data transmission through strong cryptographic encryption, and provides the ability to control the car at a distance of up to 1.5 km.

A clear picture on the screen and a convenient menu contribute to comfortable driving by the car owner. The key fob displays all the necessary indicators, including the battery level of the device and car battery, engine temperature.

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

Autostart of the vehicle engine has many useful settings that will greatly facilitate the use.

Technical specifications

• MAGIC CODE PRO 2 ensures the safety of code packages from possible theft.
• If the key fob is lost, it will be possible to disable the protection of the anti-theft system using a personal PIN code.
• The locks on the doors are locked and opened when the ignition is turned on and off.
• The activation and deactivation of the security mode is carried out by different keys.
• High range of receiving a signal from the block.
• The trunk lock can be opened without disarming the car.

Keychain functionality

• The device has many different functions, has 4 control buttons and a high-contrast LCD display.
• Remote start of the engine when the corresponding command is activated.
• It is made from quality materials which withstand scratches and falls from low heights.
• The Battery Save Mode feature helps economical use charge.
• The presence of an alarm clock that activates the autostart of the motor at a specified time.
• Indication of time, temperature in the cabin, car battery.
• The screen has an automatic backlight.
• Button lock function.

autorun

• The function is suitable for vehicles with automatic and mechanical box gears, as well as those with Start and Stop buttons.
• Autostart is performed at a pre-programmed time.
• The inclusion of the motor is monitored using the signals of the generator and the tachometer.
• The system fully functions with engines that run on gasoline and diesel fuel.

The Sherkhan Logicar A anti-theft system has all the necessary protective functions that will be able to fully protect the vehicle from possible theft using intelligent hacking, and sound alerts will warn the owner about an attempt to open door locks. An additional level of security is a 2-digit code that is entered using a key fob, and which only the owner of the car knows.

Because of a large assortment anti-theft systems in the modern car market, many consumers are faced with the problem of choice. And it doesn’t matter what price segment the alarm belongs to - both cheap and more expensive models equipped with many useful features but how to do right choice? In this article, we will tell you what features the Sherkhan alarm system has, what models can be found on sale and how to use the system correctly.

[ Hide ]

Peculiarities

To begin with, let's consider the functional features of anti-theft systems using the example of Magikar 5, 6 and 7 models:

• the possibility of auto-starting the internal combustion engine - we are talking about cars with both “automatic” and mechanical transmissions;
• the possibility of installation both on cars with gasoline units and diesel ones, including cars equipped with turbocharged internal combustion engines;
• the function of starting the power unit on command from the remote control;
• autostart of the power unit every two hours, or at the set time every 24 hours;
• if necessary, you can track the start of the power unit by signals from the generator unit or by noise occurring in the vehicle's electrical network;
• personal access code to the salon in case of loss of the key;
• the signaling can be connected to the central lock of the car, as well as the tailgate lock;
• option for programming the type of blocking relay that blocks the operation of the power unit in the event of a car break-in;
• the function of arming the vehicle in automatic mode - for its implementation, the control unit must be programmed;
• if you set up the automatic arming function of the car, the signaling system will warn about this in advance by means of sound signal;
• the option of automatically arming the car in the event that the car doors were not opened, the signaling system will also warn the driver about this with a sound signal;
• the ability to protect the vehicle without activating the siren signals;
• the presence in the anti-theft system of two programmable channels for controlling additional devices;
• also, a motorist can connect both negative and positive door sensors;
• the control unit has a special input for the negative tailgate controller;
• the ability to configure the automatic function of opening and closing door locks in case of starting or turning off the motor;
• the car owner can configure the system in such a way that it activates the protection of the car both with and without the accompanying sound signal;
• if the car owner puts the car on protection, while one of the car doors is open, the signaling will warn him about this, but this function should be programmed in advance;
• a highly sensitive shock controller is connected to the control unit, and the car owner can independently adjust the sensitivity;
• If necessary, it will be possible to configure the option " Free hands”, which will automatically activate or deactivate the security in case of approaching or moving away from the car;
• if the driver forgets to turn off and arm the car, the anti-theft system will warn him about this (the author of the video is the scherkhanalarm channel).

All additional options configured in accordance with the installation and configuration instructions. The technical manual for the car alarm clearly indicates all the steps that must be performed to configure a particular option, please note that the steps may differ depending on the model.

Briefly about the functional features of the signaling control key fob (using the Magikar 5 model as an example):

• multifunctional four-button remote control equipped with an LCD screen;
• the Magic Code system is implemented, which allows to protect the key fob from signal interception;
• the display of the device shows confirmation of the functions and commands performed, and all commands are accompanied by sound confirmation;
• the possibility of a vibration call if necessary;
• the signals reproduced by the key fob are loud enough, which allows the car owner to always be aware of the security situation;
• the range of the remote control is about 1.5 kilometers, of course, we are talking about an open area without interference and buildings;
• option automatic backlight screen;
• the display shows the main data on the operation of the anti-theft system, in particular, the indication of the battery discharge in the remote control, the battery voltage of the car, the temperature in the car, the time, as well as the operation of the engine after autostart;
• using the control panel, as mentioned above, you can start the motor, given function is programmable;
• if necessary, the car owner can also program the time to the nearest minute at which the power unit will need to be started;
• in the event that the signaling siren works, the key fob will make a sound, and a characteristic message will appear on the display;
• possibility quick setup and programming options directly from the remote control (the author of the video is how the non-original Sherkhan works after a year of operation - Artur Sitdikov).

Types and models

In the automotive market, you can find many different models signaling Sherkhan, consider the most common of them:

1. The Magicar line is considered one of the most popular. Such models are equipped with an automatic start option, and data transfer is carried out over a channel protected from interception. The average range is about 2 thousand meters. The encryption algorithm changes with each subsequent signal, as a result of which the probability of hacking is minimized. AT total there are about 14 models in this line, and all of them are characterized by low price and functionality.
2. Mobicar line. The models belonging to this line have all the technologies that allow you to reliably protect the car. Such signaling devices are equipped with control units that are compact in size, and the system can work with any digital bus, and it will be possible to manage it even with the help of a mobile phone.
3. Universe line. Such signals are telematic devices that allow you to accurately determine the coordinates of the vehicle. According to the manufacturer, the range of notification and control in this case is not limited, although in fact this is hard to believe. It is also possible to use data from remote diagnostics and study the history of trips by car. The main feature of the models of this series is the provision to consumers free services in online and offline modes, and the car owner will be able to monitor the movement of the car using a smartphone or PC.
4. Logicar. This series includes 6 models anti-theft installations, one of the most popular is Logicar 1. In general, such systems are quite similar to the Magicar described above, however, in this case, the signal reception range is 1500 m, as a result of which their cost is more affordable. The signaling of this series implements the AES-128 encryption system, which allows you to protect the car from hacking or reduce this probability to a minimum. The system allows you to monitor the degree, temperature of the motor, and also find out how long the engine has been running after automatic start.
5. canyon. Such a system is characterized small size control unit, the range of the key fob in this case is 1.5 km. If necessary, the car owner will be able to configure the central lock in such a way as to install an immo crawler.
6. Taiga. The products in this range are originally intended for mounting on trucks, special equipment, as well as other types of transport. The main condition is the presence of 23 volts of voltage in the on-board network. The Sherkhan Taiga alarm will protect not only the car from burglary and theft, but also the cargo that is transported in it. Thanks to the remote control with a liquid crystal display, the car owner will be able to monitor the condition of the car. The range of the signal in this case is 2 thousand meters.
7. Media One. It is characterized by the presence of two-way communication, as well as the autorun option. The car owner can control the vehicle using commands given from the remote control, which, in turn, is equipped with an OLED display. It should also be noted that the system is equipped with two charging devices, which, if necessary, can be connected to the battery or the mains.

Instructions for use

Every car enthusiast who has installed and connected an anti-theft system at least once in his life knows that this is quite difficult task which not everyone can handle. If you make mistakes during installation, you may encounter further inoperability of the signaling, so if you decide to do it yourself, you should be careful (the author of the video is the AVTOservis Nikitin channel).

How to install?

The alarm setup looks like this:

1. First of all, the control unit is installed, it should be placed in the passenger compartment, behind the center console, so that access to the device is difficult. Especially for an attacker. The unit must not be exposed to moisture.
2. The siren is installed in the engine compartment, it should be placed with the mouthpiece down. Keep the siren away from the motor as high temperatures subsequently put it out of action.
3. Next, the shock sensor is installed, it is desirable to put it so that it can respond to impacts on the car body from all sides.
4. The immobilizer crawler should be connected to the immo unit.
5. On the windshield put antenna module, as well as an LED that will report on the operation of the signaling. If the system includes additional elements, they must be installed in accordance with the instructions in the instruction manual.
6. It is also necessary to install the Valet service button, its installation is carried out in any place inaccessible to an attacker. The button can be placed dashboard, under the steering wheel, in or behind the glove compartment, under the pedal, under the seat, etc.

How to connect?

When all elements of the anti-theft system are installed, they will need to be connected to each other. We will not talk about the connection in detail, since this procedure is individual for each alarm model. We only note that the system should come with a connection diagram, which you will be guided by.

How to setup?

The signalization is also configured in accordance with the service book. Consider the tuning features using the Magikar 10 model as an example. The tuning process begins with programming the CAN module, this is the main stage, in this case, you must first determine the firmware number, it is indicated on the control module.

Not less than important point when setting is programming functions. To set the settings for the closers used to close the windows when arming the car, reprogram options 2-4 to position 2.

As for the other equally important features:

1. To activate slave mode, you must set option 2-14 to position 2.
2. To deactivate the option to return to armed mode, set options 1-8 to mark 3.
3. If you want to open the tailgate using the remote control, on command, while the car is armed, the alarm will work. To avoid this, it will be necessary to move function 1-1 to position 3.
4. To activate the start function of the power unit on idling, you need to hold down the Valet button for a few seconds. When it is pressed, the indicator should light up and go out. alarm. When this happens, the Valet button should be released, then wait about five more seconds and hold it down again for 4 seconds. As a result, a siren signal should sound, this will indicate a successful system setup.

How to disable?

How if the anti-theft system does not respond to key fob commands? To do this, you can use the Valet button, the shutdown procedure is also individual for all models, we will consider several options. However, if you entrusted the installation of the signaling to specialists, it is not a fact that you will be able to find this button. Then you can try to turn off the siren by manipulating the ignition.

Let's start with the Magikar 2 model:

1. First you need to open the car with the key.
2. Next, you will need to turn the key in the lock four times from the ACC position to the ON position, this must be done in three seconds.
3. Then the ignition is switched off.
4. Now the siren should turn off, while the dimensions will blink once, and then twice more after six seconds.
5. The alarm is disabled, now you can try to start.

For the Magikar 4 model, the instruction is similar, the difference lies only in the position of the key - if in the previous case it was transferred from the ACC position to ON, now it should be transferred from Lock to ON. All other steps are repeated.

For Sherkhan Magikar 6 models, the instruction is different, in this case you need to know the system code in advance, initially it is 1111:

1. So, first the car is opened with a key.
2. Then you need to move the key in the lock from the Lock position to the On position three times, you should have time to do this in four seconds.
3. Then the ignition is turned off.
4. Next, you need to repeat the second paragraph, but now be careful. The number of key positions in the lock must correspond to the first digit of the code, that is, if it is 1, then the key is turned once, if 4, then, respectively, four times.
5. Then the ignition is turned off again.
6. After completing these steps, after four seconds, the signal should flash once, so it will warn the driver that he must enter the next digit of the code.
7. Points 2 and 3 must be repeated, the procedure is carried out until all the characters of the code have been entered. Please note - in the intervals between the points, the signaling must give "permission" to enter the following numbers.
8. When you enter the last digit, the system should blink twice.
9. In the event that you have performed all the steps correctly, the siren should turn off and you should be able to start the engine (the author of the video is the Nicholas291979 channel).

Pros and cons of the anti-theft system

Briefly about the advantages and disadvantages of the Sherkhan anti-theft system, first the pros:

1. Decent build quality of all elements, thereby increasing the reliability of the system as a whole.
2. Easy to install, pretty simple circuit connections. Thanks to this, almost every motorist will be able to install and connect the system.
3. Protection of communication channels from interceptions, which is due to the implementation of a reliable pulse encryption system.
4. The convenience of use. If you do not bring down the settings, then the operation of the system will not cause you any questions.
5. High service life. The manufacturer guarantees uninterrupted operation of the system for five years of operation, but in fact its service life can be much longer.
6. Possibility of uninterrupted functioning practically in any climatic conditions.
7. The system control panel is characterized by technological energy saving system, thanks to which the remote control lasts quite a long time.

As for the shortcomings, as such, there are none. In practice, all the disadvantages are associated either with incorrect installation or with factory defects; for some consumers, it is difficult to program the automatic start function. The disadvantages include the fact that the radius of action declared by the manufacturer does not always correspond to reality. 3. Scher-Khan Media One is one of the most expensive options(price - about 16 thousand rubles)