Alarm stalker 600 wiring diagram. Experience in owning alarms Stalker (Stalker). Availability of digital LAN bus

First of all, I would like to draw attention to the system of interactive signal exchange between the key fob and the main unit, which is unique for car alarms (according to the manufacturer), which is called " Dialog code". As conceived by the engineers, the dialogue code is built in such a way that it completely eliminates the interception, substitution or distortion of messages on the radio, which makes it impossible to use code grabbers (devices for intelligent hacking / bypassing car security systems), and indeed, at the time of writing, the alarm It has been on sale for several years, but information about the existence of a code grabber for it on the Internet could not be found. Second distinctive feature of this security system, I would call operation at a frequency of 433 MHz, which provides an incredible range of the key fob (1200 m in key fob mode, and 3000 m in reverse mode), as well as colossal resistance to interference, or rather, it is not the frequency itself that gives resistance to interference, but rather a small number of other devices operating at this frequency. With the main pluses finished, let's move on to the functionality.

Remote/remote engine start

For those who are not in the know, I will say that remote engine start is a function that allows you to remotely (from the key fob) start the car engine. The function is extremely useful both for the CIS and for hot countries or countries with a predominant cold weather. In winter, you can warm up the engine and interior, and cool the seats in summer, remembering to leave the air conditioner on beforehand. In Stalker 600LAN3, the possibility of remote start is implemented perfectly, the key fob signals successful / failed to start. It is possible to set up a 15 and 20 minute warm-up, as well as auto-start by timer or minimum temperature which is especially convenient for cars with diesel engines in the cold season. I want to note that in order to implement this function, you will need to separately purchase an MS-A4 or MS-A5 autorun unit, as well as a standard immobilizer bypass module, if your car is equipped with this same immobilizer from the factory. It is easy to find out whether your car is equipped with a built-in transponder, you should wrap the ignition key handle with metal foil, and then try to start the car, if the attempt fails, then there is still a chip in the key, and bypassing the module will have to be purchased. Separately, I want to note that remote start Stalker will be able to work with both manual box gears as well as automatic.

Motion start sensor

In this Stalker alarm model, the manufacturer added a seemingly insignificant, but very convenient function - locking the doors at the start of movement, which was impossible in previous models due to the lack of a movement start sensor in the main unit of the security system. Previously, you could program the car alarm to lock the doors either by a timer or by closing all the doors, which was fraught with an unpleasant situation when the key was in the ignition, the key fob, the doors were locked, and you were outside the car.

Transponder/immobilizer tag

Stalker 600LAN3 is equipped with a system that prevents car theft by throwing the driver out of the passenger compartment. Thanks to the radio tag, the car will stop itself after a programmed time if it does not find this very tag in the car interior. Naturally, all this will work correctly if you carry the tag with you separately from the ignition key and key fobs. I would like to note that the data exchange between the tag and the main unit is not interactive, that is, potentially subject to intellectual hacking. Label polling can be programmed for the following events:

start of movement
with a delay after the start of movement
by closing the last door

It is also possible to completely disable the polling of the tag, if given function you don't need.

Voice interface

As in the previous model, the 600LAN3 has a voice interface that notifies the driver of alarms, the time of the last engine warm-up, and also facilitates system programming. The voice interface will also notify you if a new key fob is added to the system, which will protect you from “bad” service stations. The alarm will speak to you in Russian.

LAN bus

The LAN bus is difficult to attribute to functions, rather to features, but I can’t stop at it. Thanks to the LAN bus, the Stalker 600LAN3 has become ideal solution for the author's installation of alarms. A bus is essentially a wire that carries a digital signal, and you can daisy-chain to this wire optional equipment. The fact that the bus signal is transmitted digitally, and not analog, excludes the possibility of simple connection / replacement of other devices by intruders. Also, according to Magic Systems, this signal is encrypted and encryption is based on the signaling PIN code.

Programming button (Valet)

I think it is difficult to surprise with a programming button, since even the cheapest Chinese security systems are equipped with it. In Stalker, this button differs only in the presence of two positions, which in some cases makes entering commands / pin codes more convenient. By the way, since we are talking about the button, I want to separately note that if you forgot / lost / broke the key fob or tag, you can still turn off the security by entering a personal PIN code, which can be life-saving on long trips.

Disadvantages Stalker 600LAN3

This time it was not without a fly in the ointment, and most of this spoon became a key ring. The quality of the plastic used in the key fob is extremely low, as is the build quality. Having placed the remote control on the asphalt, you will most likely have to assemble it in parts, although the Chinese alarm panels are made much better. And all this despite the fact that for the replacement of this very key fobs, official dealer will charge you $100. A special Leather Case which will cost you around $7. The cover is made of black leather and fits quite well.

That's probably all that I wanted to invest in a review of this format. I would like to believe that the article helped you, and most importantly, now you can more objectively evaluate an expensive security system Stalker 600LAN3.

How to properly cut a boneless herring

E-cigarettes hurt or not?

Meals in fasting, what dishes can you eat

How and what to choose a bath: acrylic or cast iron

How to choose a kitchen mixer

Stalker-600LIGHT is a light version of Stalker-600NB, a recognized leader among bilateral car alarms in car theft protection. Stalker-600LIGHT is designed for the mass consumer, but at the same time retains the best features of the top version, such as:

Narrow-band radio path NB (Narrow Band), which has no analogues in the Russian and world markets in terms of noise immunity and range of reception and transmission in real urban conditions;
Dialogue code in the radio channel and digital LAN immobilizers, providing absolute protection against any means of electronic hacking;
Digital LAN architecture - a unique development of Magic Systems, which allows without special efforts increase capacity and service capabilities anti-theft complex;
A beautiful and stylish keychain pager with a large display, intuitive menu, channel control, event log, vibration mode and backlight.

All this allows you to create on the basis of the alarm Stalker-600LIGHT security complex with the widest range service functions, most effectively resisting theft.

Specifications STALKER-600LIGHT

Control radio frequency: 433.92 MHz ±0.2%
Control code type: dialogue code D²
The range of the key fob when giving control commands: up to 1200 m
Key fob range when receiving status signals: up to 3000 m
The supply voltage of the main unit is constant: 9 ... 15 V
Power supply voltage of the main unit for one hour: no more than 18 V
Current consumption of the main unit in ARMED mode: no more than 30 mA
Autonomous power supply voltage: 9 V (element 6LR61 ALKALINE)
Key fob supply voltage: 12 V (element A23/A27)
System current consumption two-way communication: no more than 12 mA
Key fob-pager supply voltage with LCD display: 1.5V (AAA element)
Temperature range of main unit and transceiver: -40...+85 °C
Temperature range of key fob and key fob-pager with LCD display: -5...+40 °C
Temperature range of anti-burglary card: +1...+40 °C
Frequency of radio channel monitoring: 80-90 s
Audio signal output: 1.5A or less (positive potential)
Engine lock output: 5A or less (continuous)
Number additional channels: 6
Load current of outputs of additional channels: no more than 0.15 A
Protected areas: contacts (hood/trunk, doors), cable (accessories), built-in shock sensor, outer zone of microwave sensor, central lock input, ignition lock input
Shock sensor sensitivity setting manual
Shock sensor sensitivity setting automatic: by impact force
Operational change of sensitivity level in ARMED mode manual: by command from the key fob
Prompt change of sensitivity level in ARMED mode is automatic: by number of alarms
Operational change of the sensitivity level in the intelligent protection mode: by signals from the MKV sensor
Self-monitoring when arming: shutdown faulty zone, owner alert
Signal duration in ALARM mode: no more than 25-30 s.

Equipment STALKER-600LIGHT

Main unit: 1 piece
Keychain: 1 piece
Key fob pager with LCD display: 1 pc.
Wire harness kit: 1 set
Limit switch: 2 pcs.
Code switch: 1 pc.
Transceiver unit: 1 pc.
Instruction manual: 2 pcs.
Packing box: 1 piece

Connected devices to STALKER-600LIGHT

RL100 new - network immobilizer
RL300 new - network immobilizer
MS-RIL - network immobilizer
MS-PGSM LIGHT - GSM auto pager
MS-PGSM4 - GSM autopager
MS-A4 new - remote and auto start engine
MS-M2 - power window control module.

Alarm Stalker 600 has received recognition among compatriots, since regardless of design features auto, will provide effective protection from theft. According to the developers themselves, the system can be installed on any make and model of the machine.

[ Hide ]

Description

Car alarms Stalker 600 Light, Light3, Lan3 and other versions are produced in St. Petersburg, are engaged in production Magic brand systems. The manufacturer has introduced an interactive code into the operation of the security complex, the presence of which helps prevent electronic hacking. The code is transmitted between the alarm pager and processor devices that are mounted in the car. In accordance with the application guide, it is supplied as a changing code value. There is no data transfer algorithm, which will not allow criminals to identify it and hack the complex.

Equipment

Set new alarm Stalker Lan for auto:

Processor block. This device is equipped with several additional devices. The block recognizes the label, its right job allows you to register new remotes, autostart the engine by temperature, etc.
Basic pager equipped with a screen. This device allows you to configure the security complex. Used for control.
A spare pager without a display. However, it has all the options, like the main key fob.
A special device for playing voice commands. This device can be called calling card manufacturer, since the system itself is quite convenient and practical. Through the use of voice commands, the car owner can find out about the condition of the car and what is happening to it. If the driver forgets to lock door locks, trunk, the engine warm-up time will increase, security zones will work, then the system will warn the car owner about this. You can set the system so that messages are played back by a male or female voice.
Switch. Its presence allows you to turn off the security complex if you cannot use the pager. For example, when the device is lost or the power supply is discharged in it.
The package also includes two special anti-robbery cards. In fact, only one of them can be used, the second is used as a spare. This element functions on the principle of an indicator. It must be in the owner's pocket. When the driver for some reason moves away from the running engine of the car, the power unit is blocked. For example, this might happen if robbery by car.

Full set Stalker 600

Characteristics and features

Technical properties of "signaling":

the frequency at which data is transmitted between the elements is 433.9 MHz, while the deviation should not exceed 2%;
the value of the voltage from which the security complex is powered is from 10 to 15 volts; installation of the system on heavy trucks with a 24-volt on-board network is not allowed;
the temperature range of the processor module is from -45 to +80 degrees;
temperature range for the operation of anti-robbery tags - from 0 to +40 degrees;
when the protection mode is activated, the amount of current consumed will be around 30 mA;
the range of the signal in the receive mode will be up to 2500 meters, this maximum rate, which can be achieved in conditions of good visibility and no interference;
when operating in the pulse mode, the range of the security complex will be no more than 1300 meters;
due to the presence of two-way communication, it is possible to program the start of the power unit, the type of transmission that the car is equipped with does not play a role.

Features that distinguish the Stalker 600 alarm from other security systems:

The presence of a LAN bus. Its use provides not only facilitated installation of the "signaling", but also makes it a full-fledged anti-theft complex. Thanks to the LAN bus, system control is distributed among several blocking devices. When one of the devices becomes inoperable, other modules replace it. main feature tires is a narrow range of operation and effective interference resistance. Even if criminals have information regarding the range of the bus, they will not be able to intercept the signal as a result of a regularly changing code. If necessary, the consumer can additionally connect auxiliary accessories to the bus, which will increase the resistance to burglary.
The next feature is that all relays of the system operate almost silently. When hacking, criminals often search for signaling elements by sound. In the case of the Stalker 600, this is not possible.
An important feature is the use of a three-axis motion controller. The sensor is triggered when the vehicle is tilted, lifted or shifted. That is, the device captures any changes that occur in the position of the machine. The use of this sensor will be useful in case of evacuation of the protected object. The car owner will be able to find out about this in a timely manner.
The design of the alarm control pager includes metal components. This allows you to ensure the durability and stability of the device to external influences.
"Signalka" protects almost all areas in the car, including the luggage compartment, hood and sunroof.

In addition to the Stalker 600 alarm, you can connect a GSM beacon. When the car is stolen, this device will tell the car owner the coordinates of the car. Beacons can operate offline for a long time.

Kinds

Signaling models that can be found on sale:

Stalker 600 Lora. This is one of the latest developments of the company. Modern technology signal transmission allows you to warn the car owner about dangers even when the jammers that are physically located near the car are turned on. To configure the functions of the security complex, you can use your smartphone by connecting to the system via a wireless bluetooth channel. There is an immobilizer function that allows you to block the engine in case of an attempted theft. The built-in autostart function will provide a remote start of the car engine by temperature or by time. The range of the “signaling” outside the city can be up to 14 kilometers. This system will cost the consumer about 18 thousand rubles.
Stalker 600 Super. In addition to the traditional capabilities of the security complex, the system searches for a car using the signals of GLONASS and GPS satellites. AT GSM module two SIM cards can be installed, and a special application on a smartphone is used to monitor the status. In addition to anti-robbery tags, this model of the complex is equipped with a built-in battery and allows you to connect to processing unit up to eight cameras. For prevention, link monitoring is used. For this complex, the consumer will have to pay about twenty thousand rubles.
Stalker 600 Start. This model equipped with a built-in CAN interface, which allows its installation on any modern machines. The car owner has the ability to control the coordinates of the protected object due to the presence of a GSM module, with the help of this device it is possible to control the alarm. The system implements two-level authorization, that is, first, the “signaling” is turned off by the pager, and then it identifies the car owner by the label. There is an option of built-in autostart, which will allow remote start of the motor on command or in accordance with various conditions configured in advance by the car owner. It is allowed to connect Webasto heating devices via a digital bus. Especially for owners of Hyundai and KIA cars, the kit includes keyless crawler motor blocker. The cost of a car alarm is about 12,500 rubles.
Stalker 600 NBV. The system was developed on the basis of the Agent MS module from Stalker, the main feature is the presence of the CAN interface. The package includes a GSM unit and anti-robbery tags, monitoring of the machine can be done through the official website or application for a mobile device. In order to prevent the interception of signals, regular blocking of radio channels is used. The flexibility of settings will allow even inexperienced car owners to program the main options on their own. The cost of the complex is about 15,500 rubles.
Model 600 Lan3. The two-way communication alarm is characterized by extensive functionality. According to the manufacturer, this model is the best in terms of range in a metropolis. In the city, the range of the communication channel will be up to three kilometers, and in open areas this figure will increase to 4.5 km. The dialog code effectively protects the communication channel from interception. The package includes a whole network digital devices blocking the engine. The model is out of production, so we can not specify its value.
3. According to the developer, the presence of a dialogue code allows you to 100% protect the car alarm from signal interception by all code grabbers that exist today. In open areas, the range of the remote control will be up to 4.5 km, and in urban conditions - no more than three kilometers. Thanks to the presence of a special MEMS sensor device, the accuracy of the functioning of the motion and sensitivity controllers is increased. Since the processor module operates silently, it can be hidden from criminals anywhere in the cabin. The model is no longer supplied to the domestic market, so we cannot name its official cost. But you can still find these alarms on sale.

The Anti-Theft channel spoke about the installation of the Stalker complex on a Volkswagen and the basic functions of a car alarm.

User manual

Below are photos of programming tables, which are used to configure the system functions.

Table 1 Table 2 Table 3 Table 4 Table 5 Table 6

Activating and deactivating alarm modes

The nuances of using the keychain:

Inclusion guard mode is done by pressing the pager button in the form of a locked padlock. If it sounds sound signal, the command is accepted by the complex. There will be a closure door locks, the car alarm will start diagnosing the status protection zones. The turning lights of the car will blink once. For 15 seconds, the lighting in the cabin will be activated, and then the "signal" will perform an indication by means of a diode bulb.
If you need to activate protective mode with the microwave controller disabled and shock controller sensitivity reduced, the operation will be different. First, the car owner enters the menu, and then clicks once on the button in the form of an arrow up and presses the key in the form of a locked padlock. The display will show an indicator in the form of a hammer next to the car.
The activation of the intelligent protection mode is carried out in almost the same way, only to select a function in the menu, you must double-click on the button with the up arrow symbol. After selecting the function, the key with the closed lock is clicked.
If you need to turn off both controllers (microwave and impact), then after going to the menu, click on the button with the up arrow three times. The command is sent by pressing a key in the form of a locked padlock. This feature will be useful if the car is parked in a turbulent place where there is a lot of traffic nearby. In particular, we are talking about trams and trucks.
To enable the option to search for a car in the parking lot, you need to go to the settings menu by pressing the button in the form of an open lock. The up arrow key is double-clicked to select a function, and then the locked button is pressed to send a command. The pager should display Find. Turning lights of the machine after activating this option will blink periodically. The siren will emit periodic beeps.
To unlock the tailgate lock, enter the setup menu (button with open lock) and press the up arrow key three times. By pressing the button in the form of a locked padlock, a command is sent. One beep will sound to confirm.
If the car is equipped with glass closers, then you can set the partial or complete closing of the windows. Enter the setup menu by pressing the button with the open lock, and then four times click the up arrow key. Select a command and activate it by pressing the button with the indicator in the form of a locked padlock.
If necessary, the car owner will be able to view all the events recorded by the security complex in his absence. The pager's memory can store information about 35 events that occurred when the security mode was activated. Enter the setup menu by pressing the padlock key, press the down arrow key once and press the padlock key again. List will appear on the pager's display, and data on all events will also be displayed. Scrolling is done by pressing the up and down arrow buttons.

The Theft Channel No showed in practice what the range of the Stalker security systems is on the example of the 600 Lora model.

Autorun feature

To enable the remote engine start option, the car must be prepared in advance:

Especially for the implementation of this function, the Stalker security complex is equipped with a toggle switch, it must be switched to the on position. The switch lever is exposed upwards.
If the car is equipped with a manual transmission, then the gearbox lever is set to the neutral gear position. It is also necessary to take measures so that the car with the engine running does not accidentally roll. To do this, you need to turn on the parking brake lever, and if it does not hold well and the car rolls anyway, stops are placed under the wheels. In cars with automatic transmission gears, the transmission selector is set to the park position.
Then, with the engine running, the key in the lock is transferred to the off position. The key is then removed from the lock. If the vehicle is equipped mechanical box gears, the power unit will continue to work, automatic - the engine will stop. By sending a voice command, the security system will inform the driver about the readiness for remote start.
Within one minute, you must have time to leave the car, close all doors and the hood, and activate the security mode. On machines with manual transmission, after these steps, the engine should stop.

Detailed analysis of characteristics car alarm Stalker-600 version Light3. Here you can find information about each individual component of the device.

Key characteristics of the Stalker-600 alarm

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

The presence of a dialogue code can provide a 100% level of protection for the Stalker device against any possible ways electronic "hack" of the car's security systems. The use of a narrow-band noise-resistant radio clock (NarrowBand) is an unambiguous guarantee that the signal will be provided with maximum noise immunity in urban areas. In this case, Stalker Light3 has the same extended range as the Stalker LAN3 version: in urban areas, this distance has a maximum range of up to three thousand meters, and in a direct viewing environment, this distance increases to four thousand five hundred meters.

Automatic channel control forces the key fob to constantly communicate with the main unit of the security device. Thus, when trying to deliberately jam the radio communication, the owner will be sent a message about the theft taking place on the mobile phone in real time.

The correct and perfectly accurate functioning of the system slope sensors, inclination and displacement sensors is due to the work of the upgraded MEMS sensor. The presence of solid-state relays with silent switching during the working period allows you to hide the main car alarm unit from criminals in the most reliable way.

Availability of digital LAN bus

It is possible to use the LAN architecture to create a powerful anti-theft complex with huge amount auxiliary security and warning modules. LAN works on the basis of conversation type car alarm. You can connect an auxiliary anti-theft device immobilizer to realize anti-theft function, you can also connect a GSM satellite type car pager to realize a monitoring system, as well as an alarm alert on a smartphone. Thus, your car will gain exclusively reliable protection in the form of a powerful anti-theft complex of the first class.

Monitoring Internet service CarOnline

There is also an excellent opportunity to monitor the movement of the car in real time and control all blockages from your own smartphone. When you connect a GSM satellite car pager called MagicSystems, the dialogue-type car alarm system Stalker 600 activates the ability to monitor the routes of your car.

If something happens to your vehicle, your mobile phone will immediately receive calls and text messages. Be sure to use full version website Car-Online by going to your Personal Area. The application on the smartphone will throw out data about the current location of the object, as well as the status of the security system of the vehicle. The user will also be able to find out information for all the days when the system worked.

Modern keychain design

The car alarm keychain has become more modernized: it has a softtouch coating.
The alarm keychain will be a great addition to the owner's car. Also, the key fob has a built-in "smart menu". You can switch on various security modes, monitor the level of communication, and also activate the start of the engine system remotely. The operation of the key fob is carried out thanks to a small AAA battery, which can work flawlessly for 6 months. The distance at which the car alarm can work is four and a half kilometers, when located on an open area.

List of key features

The key fob has a liquid-crystal display type, made of plastic with a wear-resistant structure, also has a special coating called SoftTouch.
A code for carrying out authorization of a dialog type, which provides reliable protection against opening the device with a code grabber.
The relay, designed to control the light signaling, is provided with a silent operation mode.
The distance that the alert travels is four and a half kilometers if you are in open type terrain.
The notification range of the owner in urban areas is quite high.
An uninterrupted communication channel management system that operates on an ongoing basis.
The presence of a shock sensor with an adapted sensitivity of MEMS sensors.
Availability of tilt sensor and displacement sensor.

Car alarm Stalker-600 from MagicSystems is one of the digital products not so common on the domestic market. anti-theft systems. It is designed to work with digital blocking relays. Unlike the standard relay, the digital one is assigned a unique code. The switch is triggered after the encoded signal arrives. The number of installed relays is not limited. In addition, the stalker 600 alarm system has in its assortment a digital bus designed to connect 10 peripheral devices.

Alarm Stalker

Radio channel analysis

The developer provided a control key fob for signaling. This is not a simple device, which today is equipped with most security automotive systems. It uses a special mode of determining the owner, namely the dialog. The bottom line is this. AT standard system central block control performs the assigned tasks, having received a signal sent from the key fob, with its own distinctive cipher. In interactive mode, the situation is slightly different. The main unit, having received its signal from the key fob, double-checks whether this is really the case and sends an additional question. After receiving the correct answer, it executes the command.

As for the radio signal stream, it should be noted that a special coding system is used here. To speed up the signal, special transceivers are used, which reduce the signal transmission time.

In addition, a special signal transmission system is used, which protects it from interference and increases the range of the operating range. These benefits will primarily be appreciated by residents of large cities. If the car is parked in a large parking lot, for example, near a hypermarket, then in order for the car to respond to the signal, it is often necessary to come close. This is due to the fact that many owners can simultaneously send signals to their cars. Thus, the air is clogged, the signals overlap each other, and the receiver does not receive them.

Some car alarm developers simply increase the power level of the transmitted signal, which actually only complicates the overall situation. However, MS saw a way out of this situation in a different direction. They created unique receivers and transmitters that operate on a special frequency, slightly removed from the central, busiest one. Thus, broadcasting is carried out within the permitted limits, and the range of the signal sent is significantly increased.

There is one more additional function in this alarm. If the owner has lost the key fob or for some reason it has become faulty, then it is necessary to open the car with a key, resort to using the Valet button and, possibly, live in this mode for a few more days until he acquires a new key fob. As for the Stalker system, you will not find the Valet button here. Instead, a two-button dialer is provided. It allows you not only to turn off the system, but also to use all its functions to the full, despite the fact that the pin code consists of three values.

With regard to the power sources of the system, the developers also tried. The alarm has an autonomous source, which allows the owner to send a signal to the pager when the main one is turned off, thereby increasing the level of car safety.

Installation in a car

The unit is designed with all necessary ports and connectors in mind. There is no point in looking at everything. Among other things, it is possible to manipulate auxiliary devices, for which 5 channels are provided that can be programmed to suit your needs.

The system of remote and automatic start is also provided in this model. It is implemented in two ways. The first of these is through the use of personal control channels. This option consumes 3 out of 5 free channels. Thus, only two channels remain for implementing the connection of service functions. You can try to connect the blocks through a digital bus, which is quite realistic. But if necessary more free channels, it is possible to mount the MS-A2 start module, the type of which is analog, which allows you to occupy one free channel.

System differences

There are several types of the Stalker system. According to the developers, the Light version is a lightweight version of the Stalker-600NB model, which occupies a leading position in the car alarm industry with two-way broadcasting. The light version was developed as a budget option, but kept the best sides original version.

As for the relief itself, the first thing to pay attention to is the price. The difference with the original is about 3000 rubles. In both systems, identical functions can be observed.

The light version is equipped with an immobilizer. It simply does not exist, but if you need it, you can always purchase it separately.

Each version needs an individual selection necessary components. A serious approach to this issue will ensure high level anti-theft protection and acceptable comfort for the owners of this system. What is worth choosing?

Anti-theft security

The MS-RL version of the engine blocking system with a digital relay, which is located under the hood, is suitable here. The relay is controlled by a digital signal. It has its own unique code, and the transmission channel is protected by a special encryption system. The number of possible installed relays is limited only by the desire and capabilities of the owner. Here it would be wise not to save money and install another relay in a place different from the first one. So, for example, it would be possible to interrupt the operation of the fuel supply pump. It is possible to control this part of the circuit by means of a GSM/GPS pager implemented in the MS-PGSM2.

To ensure that the locks are difficult to access for unauthorized persons, it is necessary to install an auxiliary lock for the hood. It would be nice to use Defen Time in such a situation.

Usually, this lock is controlled through a separate dedicated channel. However, you can save on the channel. For such purposes, it is better to use the MS-RL2 control module, which is a digital relay with additional features. When the car is disarmed, the module unlocks the hood. And it blocks when the transport is armed again. In emergency situations, the lock is blocked.

Notification system

In order to notify the owner of the events occurring with his car, a key fob pager was included in the alarm kit. It has a fairly high performance in the field of quality and range of work. But if you want to increase them, then you can use the MS-PGSM2 pager. This allows you to receive signals not only on the key fob, but also on your mobile phone. In addition, this module carries out activation in Car-Online.

auxiliary options

Worth noting as additional features an option to open the trunk, which is carried out from a key fob pager, as well as a window glass closer.

Kit set

MAGIC SYSTEMS Stalker-600 Light - two-way broadcasting alarm with remote control through the keychain.

MS-RL - blocking relay

DefenTime - hood lock

MS-RL2 - hood lock manipulation system

MS-M2 - power window manipulation system

MS-PGSM2 - GSM/GPS alert pager

MS-NC485TCM - photo recorders (one pair)

volume sensor

Advantages and disadvantages

Of the positive points, the following can be noted:

Stable operation of the system, without failures.
Convenience when using a key fob. A fairly simple and convenient menu: there is a backlight, necessary functions are found quite quickly, the menu is circular. At the top of the list are the most frequently used ones (opening the trunk, turning on the engine).
The display shows information well both in daylight and at night.
Beeper signals do not cut the ear. The choice of functions is confirmed by vibration, which is also good.
Small power consumption by the key fob.
Excellent radio work. The signal is stable, and the radius of reception and transmission is large enough.

Among the shortcomings, the following stands out:

Absence of blocker of buttons on the pager. As a result, accidental presses in the pocket occur, which lead to the activation of the panic mode. In general, the use of a cover helps to avoid this. However, although the cover itself is transparent, dirt and dust accumulate under it over time. As a result, after a short period of time appearance the key fob is getting awful.
As a result of operation, it was noticed that the warning system does not work quite properly. In particular, it fails when the trunk is open, when the car is put into armed mode. In this case, the hood is also not locked.
Malfunction in the operation of the shock sensor: after notification of a triggered warning zone, the sensor does not respond with a subsequent strong impact.

Outcome

Stalker-600 Light is one of the best options signaling with two-way broadcasting in the vast domestic market. The price makes it affordable. The complete set is very pleasing, since it allows creating an elite-level security system based on the built-in functions of the supplied modules. At the same time, the detected shortcomings are not so significant as to reduce the overall assessment of the system. Big number unique technologies allows this complex to be a competitive product in the automotive protection systems market.

Not really

Categories

Popular