Unusual DIY photo frame decor ideas. Do-it-yourself photo frames from cardboard, paper, improvised materials on the wall with your own hands What can be done from a photo frame

Probably each of us has photos that we want to keep forever. It is for such photos that you can make a beautiful photo frame with your own hands.

You can decorate your home with a handmade frame or just give it to loved ones.

How to make a photo frame out of cardboard

1. Cut out a rectangle of any size from cardboard.

2. In the middle of the cut out rectangle, cut out another rectangle. Its size should be slightly smaller size Photo.

3. Decorate the frame however you like.

You can use stickers and/or draw something.

You can also draw animals on colored paper, for example, then cut them out and glue them to the frame.

4. Prepare another sheet of paper and cut a rectangle out of it. Its size should be equal to the frame size.

5. Glue this rectangle to the back of the frame, leaving one side untaped so you can insert your photo through it.

6. It remains only to insert a photo!

DIY photo frames. Frame from the pages of a magazine.

This frame not only looks original, but you also don't have to pay a penny for it, since its main element is the pages of a magazine, and any that you can only find at home.

You will need:

Cardboard

Old (unnecessary) magazines

Thread for sewing

PVA glue

Scissors

Utility knife (or scalpel)

Ruler

Pencil

1. Prepare a sheet of thick paper or cardboard about 20x25cm in size. Measure 5cm from the edges of the sheet and draw a 10x15cm "window" in the middle.

2. Cut out the "window" with a utility knife.

3. Start rolling the magazine pages as tightly as you can. To fix them and prevent unwinding, use glue.

4. Prepare your colored sewing thread and start winding it around the twisted magazine pages. Continue until you have many of these blanks.

5. When the blanks are made, start bending them at an angle of 90 degrees in the right places and attach them to the cardboard frame with glue.

6. Prepare a small piece of cardboard for the legs. Also cut out two cardboard strips and glue them to the back of the frame so that you can insert a photo between them.

How to make a beautiful frame. Frame as a gift.

You will need:

Simple inexpensive wooden frame

piece of cloth

PVA glue

Ruler

Glue brush

Scissors

1. Prepare a piece of fabric on which to lay the frame. Cut as much fabric as you need to cover the edge of the frame on the front and back.

2. Now you need to cut out the excess fabric from the middle of the sheet.

3. Lay your frame on a rectangular pattern and cut out squares from the corners, this way you will provide yourself with neat corners.

4. Gently, using PVA glue, stick the fabric on the 4 sides of the frame, but just be careful not to wrinkle it. This must be done on both sides of the frame - front and back.

5. Now make diagonals at the corners of the frame. To do this, cut each corner inside your photo frame. Next, you need to fold the fabric and glue it to the inside.

* There is an option to paste over the back side of the frame with a cloth.

When the frame is dry, you can decorate it with ribbon.

How beautiful to make a frame on a spring theme

This frame is made in the spring theme. She looks gentle and romantic.

You will need:

simple frame

Artificial flowers

Glue gun (can be replaced with PVA glue).

1. Divide the flowers into inflorescences.

* If you wish, you can make flowers with your own hands. To learn how, check out one of our tutorials:

2. AT this example small petals are used, which were cut out of colored paper. These petals need to be glued to the frame with glue gun or PVA glue.

* To make it more convenient, try to start gluing the petals from the corner of the frame. Next, gradually fill the frame with petals.

* It is worth noting that the petals need to be glued tightly to each other, so your flower bouquet on the frame will seem more magnificent.

3. Use braid, lace or beautiful paper to wrap around the edge of the frame.

How to make photo frames. Painting from photographs.

If you have a lot of favorite photos, but you just don't want to buy a separate photo frame for each, then you will like this project.

Just one big photo a frame that will fit several photos at once (the size of the frame depends on the number and size of photos)

You will need:

Large picture frame (wooden or plastic; choose your size)

* In this example, the frame size is 40x50cm.

Small nails (can be replaced with pushpins)

* You can choose a set of multi-colored push pins.

A hammer

Jute (or any rope to which you will attach photos)

Measuring tape

Clothespins

* You can look for sets of small multi-colored decorative clothespins, or use regular ones, as in this master class.

1. In this example, space was measured for 5 rows of small photos, similar to those taken with Instagram. You measure the distance you need between the photos, both vertically and horizontally.

2. After that you have measured everything, nail the carnations in the right places of the frame on the right and left (or insert push pins) and pull the rope.

3. Gather your favorite photos and attach them to the string with clothespins.

The photo frame is ready!

DIY frames. Flower photo frame.

You are free to choose the color and shape of the flowers, just use your imagination.

You will need:

simple photo frame

acrylic paint

tassel

Dense material (fabric) from which you will cut flowers

Multi-colored buttons, thread, needle

Scissors

Pen

Super glue

1. Prepare the frame and paint it with two layers acrylic paint. Choose the color yourself.

2. With a pen or pencil, draw the shapes of the flowers on a dense fabric and cut them out. You can decorate them with colored thread and sew a button on top.

3. Now it remains to glue all your blanks to the frame using superglue.

4. Add a photo!

DIY photo frames. Thread wrapped frame.

Another beautiful and inexpensive photo framework.

You will need:

Simple photo frame with smooth sides

PVA glue

Several threads of different yarn colors

Scissors

1. Prepare the frame and put some glue on it. You need to do this in parts, i.e. a little glue should be applied to a small part of the frame and then wrapped around this part with a thread.

2. Start winding the frame gradually with multi-colored threads.

3. Add a photo!

Children's photo frame. Carousel.

You will need:

5 disc cases

10 photos of sizes approximately 12x17cm

10 unnecessary disks

PVA glue

Ruler

Pencil

Scissors

Scotch tape (duct tape is better)

Disc stand

Decoration tools (stickers, colored paper, sequins, etc.)

1. Take the disc out of the case.

2. Insert 2 photos on the left and right into the case. If necessary, crop the photos so that they fit well and look good in the disc case.

3. Using electrical tape or tape, connect several cases as shown in the picture.

4. cook unnecessary disks and put them on the stand (more precisely, on its stem), shiny side up, to create a slippery surface for photo cases.

5. It remains only to put a "flower" from the cases with photos on the rod of the disc stand.

DIY photo frame. Ideas.

How to make a photo frame with your own hands (video)

How to make a frame with your own hands

How to make a paper frame

DIY paper frame

DIY children's photo frame

Despite the fact that progress does not stand still and digital cameras have long replaced film cameras, we continue to arrange and hang frames throughout the apartment, which to this day are the best design for photo. Big and small, simple and bizarre shapes - all of them are designed not only to be combined with the interior, but also to reflect our mood.

That is why we propose not to depend on the whims of designers, but to rely on your own taste and try to arrange a photo in accordance with it.

1. Keep old credit cards? And you are doing it right! They will still come in handy for decorating your favorite photo! True, for this credit card will have to be cut into small pieces. But these are already details ... (ideafrom here )

3. Thrifty needlewomen will love the simple design of the frame from what is at hand. It can be buttons, old jewelry, coins... or spools of thread! Such practical free frames not only look great as a photo frame, but also fit perfectly into any interior. (original idea )

4. Artfully arranged coffee beans around the frame different varieties- beautiful design, which has another unique property - a delicate aroma. ( )

5. Don't rush to burn or throw away old "women's magazines". Thanks to the bright pages, they can become great decor for photo frame. (idea fromsite )

6. Surprisingly delicate vintage photo frame is obtained from a piece of old wire. (original article )

7. Sweet tooth will be delighted if you receive a beautiful and quite edible photo frame for the holiday. (originalidea )

8. Ice cream lovers will now eat it with double pleasure, because from sticks painted in different colors, it turns out a bright summer photo frame. (MK )

9. Few can resist the temptation and not collect shells or pebbles on the sea coast. But what to do with them then? Put in jars and carefully store as a memory? It is better to decorate a photo frame with stones and shells! (idea )

10. A glamorous frame is obtained if you decorate it with ... ordinary buttons. This option does not look primitive, especially considering that the proposed photo frame design does not require special investments, and those who have a supply of buttons will get it for free. ( )

11. Don't scold your kids for breaking pencils too often! Better use their addiction and decorate the frame with “stubs”. Looks very unusual and colorful! (details )

12. Cute and very tiny photo frames are made from bottle caps. ( )

13. Old CDs - great material for decor. Its strength and lightness will be appreciated by many needlewomen. (MK )

14. For young ladies who love everything cozy and homely, voluminous textile frames will be just a godsend. (original MK )

15. This unusual frame can accommodate photos of all family members, because it has as many as 12 cells. Guessed? It's made from an egg container! ( )

16. The most precious thing in our life is children. And their photos also deserve decent design. (idea

design solution, stylish element decor, a great gift for loved ones and an exciting activity for parents and their children - creating photo frames with your own hands from improvised materials. Most important events and pleasant memories captured in the pictures will serve as an excellent decor for your home. How to make a photo frame beautiful and creative, we will tell in this article.

Stylish interior

The most common way to make a photo frame is out of cardboard. This goodness is in bulk in almost every house, we cut it out the right dimensions. You won’t have to think long about how to decorate such a photo frame, pieces of fabric, scrapbooking paper, buttons, quilling paper, brooches, figurines, emoticons, ribbons and beads, tubes from bright magazine pages will be used.

If you have the opportunity, use glass as well so that the photo frame has a quality look.

Making a photo frame can start with buying a ready-made regular frame, just add it with individual elements that you like best. Photo frames made of shells and sea stones, twine, anchor figurines are suitable for decorating photos from summer sea holidays. Such parts are easy to seat on hot glue from a gun.

Decor with beads and ribbons for lovers of bright and shiny jewelry:

Cardboard and colored paper

Consider one of the master classes on how to design a desktop photo frame made of cardboard and paper on a stand.

Step 1. Material preparation. Cardboard, decor paper, beads, ribbons, glue, stationery knife. Cut out the desired size from cardboard. Back, stand and front.

Step 2. Decorate the main parts. We glue the decorative paper cardboard, which is the back, as shown in the photo.

Step 3. Fold from scrapbooking paper different sizes ladder, making a visual frame. We sew on a typewriter with a zigzag. Of course, you can not do this, but use, for example, a special decorative tape or just stick it on top.

Step 4. We collect the stand and bend the end. We make holes in the fold with an awl. In the future, brads, small carnations are inserted there.

Step 5. Install the stand. We take cardboard and thicken the place where the stand on the brads will be attached, we simply glue pieces of cardboard. We connect the stand and glue the cardboard to the back.

Step 6. The most important thing is to select the decorations and glue them to the frame. These can be flowers, stickers, ribbons and beads.

Decoupage options

Making photo frames will be an interesting educational activity for children with parents. Learning quilling, decoupage, pasting and painting will captivate with an amusing idea to create own craft for the decor of the children's room.

Old puzzles will certainly lose their details, which cannot upset, paint them or leave the details with the sky, water and grass, glue them randomly to the frame or just leave a smooth outline around the perimeter, if the drawing itself allows it, it will be even more beautiful.

Photo frames with the help of paper modules contribute to the development of fine motor skills of the hands, and spare parts for quilling will create a voluminous carpet of flowers and animal figures. It is easiest to glue on paper with ordinary PVA glue, which is safe and not difficult for children.

Decoupage from small parts involves the application of thick glue. Choose safe, odorless adhesives. Buttons or Lego pieces will create a bright frame, if you don’t have bright buttons, but have old ones, you can cover them with paint or varnish.

decoration eggshell, cereals, seeds, vermicelli, coffee also have a place to be in creativity, especially since such decoration materials can be painted with paints and combined with other decor elements, creating unusual patterns. Photos in the design of food can be placed on the walls of the kitchen or dining room.

Do not forget that frames are often molded from plaster or dough. The dough recipe is very simple, the same as for regular modeling. You can add food coloring to it or color it after it dries. Flour, salt and water are taken in parts 3:3:2. Make a solid frame and wait for it to dry, or if you have modeling skills, create various figures of your child's favorite cartoon characters or just animals.

Video on the topic of the article

Evgeny Kudryavtsev, an architect and father of a two-year-old daughter, invents toys and useful things made of cardboard for her. This master class is about how the problem of placing children's drawings was solved. And the child is happy, and the walls are intact!

Irishka loves to draw and, like any artist, wants her works to hang in the most prominent places. And in our small panel apartments where are these places? Correctly! Either walls or furniture. You can, of course, hang them on scotch tape to furniture. However, it does not last long, paper and furniture deteriorate from adhesive tape, and masterpieces painted with paints also strive to curl up into a tube all the time.

The walls are even worse - they are concrete! In our P-44 series, the only walls where a frame can be attached by driving a regular nail are the bathroom and bathroom partitions. In the remaining walls, you need to drill holes, hammer in the dowel and screw in the screw. And given the number of masterpieces, the speed of their appearance and the desire of the creator to see his paintings on these walls ... In general, you won’t get enough of victorious drills!

Therefore, we will make a frame out of cardboard. What's the thrill here? And the fact that it can be hung on any wall, as we will use it as load-bearing elements wallpaper and a needle. The frame is light, and you do not need to remove it to replace the picture, which means there is less risk of tearing the wallpaper with a needle. Moreover, in one frame you can hang several pictures at once, one on top of the other.

We will need the following materials and tools:

1. a sheet of cardboard, 260 × 350 mm in size;
2. a sheet of A4 paper;
3. ruler;
4. stationery knife;
5. flat screwdriver;
6. pencil;
7. single hole punch;
8. round shape template.

As the main material we take microcorrugated cardboard with a thickness of 1.5 mm. In my case, it is white on one side, and it is on this side that you need to make markings. The front side will be the reverse side of the cardboard color - because on our white wallpaper it looks more advantageous. The original size (260 × 350 mm) is due to the fact that on each side there are 25 mm left on the mat. The beginning of the markup is simple - exactly in half, horizontally and vertically.

We apply in the middle, by eye, a sheet of A4 paper and make serifs 70-80 mm long at the intersections with the marking lines. The entire sheet does not need to be circled.

Now about the round template. It's 60mm in diameter, and it's a lid for a soft-boiled egg cup, simply because it fits the diameter. In general, when you need to make something round, you need to think about the compass last, because in the house where the child lives, there are always caps for paints, children's dishes, plates, etc., which can and should be used instead. Take a look around! Surely somewhere nearby there is something with a diameter of 60 mm! We put the template in the middle of the edge of the sheet and the pencil line and circle it.

It turns out something like this!

Now we take a flat screwdriver and, stepping back a couple of millimeters from the pencil border of a sheet of paper, we push through.

And cut like this!

Flipping the cardboard front side up and extrude the cut segments.

The point is small - to make holes for the needle! They need to be made with a single hole punch, one each on the long and short sides. If there is no single, then you can take a regular hole punch.

Everything is ready! We make all the following frames according to this template. Just put on top, circle, extrude and cut out.

Now we hang a frame with masterpieces on a regular sewing needle horizontally...

Or vertical! We hang works on any wall. We do not damage wallpaper and furniture. Without a twinge of conscience and without removing the frame, we hang the masterpieces of future Picassos with future Renoirs and Shishkins.

Comment on the article "Do-it-yourself frame for children's drawings. The walls and furniture are intact!"

Section: -- gatherings (frames for drawings in Auchan). 2Alt and those who draw. I don’t know exactly what happened to Auchan in our northern Mega, but today they sell everything for ...

Graphic drawing on the wall. Help. About his own, about a girl's. Graphic drawing on the wall. But if I have some kind of graphics, drawing, but rather complex, i.e. stencil...

I take the finished frame and paint it myself: gouache is generously smeared on a dry frame after 1 minute. it is well wiped with a rag - it turns out a frame of a light shade or just paint over well on it ...

Frame for children's drawings with their own hands. Walls and furniture intact! If there is no single, then you can take a regular hole punch. Everything is ready! You can start working with children using the passe-partout technique from an early age. I wanted to take care of them and go and buy a lot of frames at once...

Frame for children's drawings with their own hands. Walls and furniture intact! Moreover, in one frame you can hang several pictures at once, one on top of the other. In general, when you need to make something round, then you need to think about the compass last, because in the house ...

Draws on wallpaper. parent experience. Child from 3 to 7. Education, nutrition, daily routine, visiting kindergarten and relationships with caregivers, illnesses and physical development of a child from 3 to 7 years old. Frame for children's drawings with their own hands. Walls and furniture intact!

Frame for children's drawings with their own hands. I decided to design for once the work Frame for children's drawings from cardboard with their own hands - a master class on making a passe-partout.

Frame for children's drawings with their own hands. We have accumulated so many photos and works of children, which are very cool, but because of the lack of frames, they are in folders and albums.

Section: Need advice (wooden frame painted with balon). How to paint the frame? Well, on the wooden frame, I had the first layer of a primer so that the wood would not shine through.

Round frame. Need advice. Mary the artisan: embroidery and needlework. Section: Need advice (First time I make out in round frame). Round frame.

Frame for children's drawings with their own hands. Walls and furniture intact! The walls are even worse - they are concrete! In our P-44 series, the only walls where you can attach a frame by hammering in the usual 2 years ago, they cost 25 rubles, and the cheapest frame in ...

Do you consider frame size when choosing a canvas? For example, if you sew at 14, and the picture just doesn’t fit into a standard photo frame, then: take 16 or smaller canvas ...

Frame for children's drawings with their own hands. Walls and furniture intact! Walls and furniture intact! Each picture - a passe-partout made of cardboard in 5 minutes. Master Class. Paint them in a contrasting color and make them like a frame (like wooden slats with ...

Frame for children's drawings with their own hands. Walls and furniture intact! Walls and furniture intact! Each picture - a passe-partout made of cardboard in 5 minutes. Master Class. About 2 years ago they cost 25 rubles, and the cheapest frame in the photo salon was 60.

how to paint a frame? Need advice. Mary the artisan: embroidery and needlework. how to paint the frame Task. need a pale green shabby frame.

Frame for children's drawings with their own hands. Walls and furniture intact! Walls and furniture intact! Each picture - a passe-partout made of cardboard in 5 minutes. Stock canvas around the edges. Vova, do you happen to know where on the net you can find how to make picture frames?

Walls and furniture intact! Can you find a smaller frame? so that it was right next to the embroidered one. and if the frame is moved in the center of the picture along the edges, what are the holes? Frames for children's drawings. About 2 years ago they cost 25 rubles, and the cheapest frame in the photo salon was 60.

Frame for children's drawings with their own hands. Walls and furniture intact! You can, of course, hang them on scotch tape to furniture. However, it does not last long, paper and furniture deteriorate from adhesive tape DIY crafts for the holiday of March 8: pictures of flowers. Creativity lessons with children.

Photographs are a repository of all sorts of moments. They keep life itself. That is why always, even in the era of digital technology, people put on the table, place on the walls photos associated with this or that event or person. Spectacular and unusual photo frames are not cheap, and everyone wants to decorate their home with a noticeable decorative element. Therefore, the decor of photo frames has always been, is and will be in demand. Decorating frames with your own hands is feasible for almost everyone, it is exciting, makes you feel like a real creator.

Paper photo frames

How much can you make out of paper? Countless products, interior items, crafts and much, much more. The Internet is teeming with ideas, one better than the other.

Origami photo frame

Necessary materials:
- colored one-sided paper;
- scissors;
- a simple pencil;
- PVA glue;
-ruler.

Base - 4 squares 15x15 cm.

Fold the square diagonally with the colored side inward.

Expand. Lay the square right side up and fold the bottom side of the square to the fold line as shown in the photo.

Turn the workpiece over and bend the bottom corner.

Turn the workpiece over to the front side and bend along the fold line.

Flip. And bend the bottom part along the fold line.

Put the side in the pocket. The module is ready.

Back side of the module.

To assemble a photo frame, we need 4 modules.

We apply glue on a sharp corner and insert it into the corner of the 2nd module, as shown in the photo.

Then the 3rd and 4th module.

The photo frame is ready.

The reverse side of the photo frame.

Insert any photo or funny picture.

Volumetric photo frame

The idea of ​​this frame is good because all you need to create it is a sheet of paper and scissors. It is also wonderful that the frame is voluminous.

The size of the frame depends on the size of the paper. And this means that you can make a frame of any format. And use it to place a photo or a collage, as well as to decorate hand-made crafts.

Print out the frame template

If you do not have the opportunity to make a printout, then make a template for a homemade paper frame with your own hands. To do this, you need to place a photo in the center of the sheet and circle its outline (or simply draw a rectangle of the appropriate size in the center of the paper). Then lay aside strips of different sizes (alternating a strip 1.5 cm wide and 1 cm wide). Make indentations at the top and bottom as shown on the template.

Next, we bend the drawn strips along the ruler. We begin to wrap the sides of the future paper frame for the photo. We do this carefully so as not to wrinkle the craft.

First, the short sides are folded, and after them the long ones. We need to insert corners long sides paper frame into the corners of its short sides to tightly fix the structure.

If the paper is very thick and glossy, it makes sense to first insert a photo, and only then fold the sides. So she "sits" tighter. If you are worried about the design, you can drop a little glue or use double-sided tape.

Quilling paper frame

Option 1:

For work, you need to prepare tools and materials:

• light wood photo frame.
• white acrylic paint
• sponge or sponge for applying paint
• quilling paper white and blue - strips 3 mm wide
• quilling tweezers
• awl for quilling
• scissors
• PVA glue
• glue Moment
• acrylic contours - pearl imitation - white and blue

Let's start by preparing the frame. It is better to take a frame made of light wood. Then you do not need to prime the frame first, and the white paint will ideally fall on the tree. If the frame is dark wood, then you will need to pre-apply primer to mask dark color tree.
Take the glass out of the frame. Sponge blotting movements apply paint to the frame, from all sides. It is better to apply 2-3 layers. And leave the frame to dry completely (after 1.5 hours the frame will dry completely).






While the frame is drying, let's prepare decorative elements, with which the frame will subsequently be decorated. I note right away that when creating such elements, there are no unified schemes or rules. All this is only a flight of fancy and the skill of working with paper.
We take 8 strips white color and glue them together with a ladder, that is, each strip is glued to the previous tip, while the tip of the strip is located slightly lower.



Using an awl, we twist the glued strips, while wrapping the strip so that the gluing points are inside.

We dissolve the twisted roll. Here is such a beautiful curl turned out.


Now we glue all the strip together in one place, just below the curl.


When the junction is dry, we give the strips a wave shape, and glue the strips again.


We cut off the remaining free ends so that each strip is longer than the other.


And twist each end.


Pay attention to the fact that it turned out big complex element. Now we glue this element to the already dried frame. The element can be bent according to the shape of the frame.






In the decor of this frame, I wanted to beat 2 colors - white and blue, as well as a smooth transition from one color to another, so let's start creating central element, but already blue color.
We glue 6 strips of paper with a ladder and twist them into a roll.

We glue the strips together in one place. Trim the ends in the same way as white element: Each stripe is longer than the previous one.


And we wind each strip on an awl for quilling.


Now we spin the previously twisted rolls. This is easy to do by running an awl over them.


Now glue this element to the frame. It is better to use glue for this moment. At the same time, we glue this element in the upper left corner, as in the photo.

We straighten the curls so that they lie in the same plane, glue them.

In order to make a smooth transition from one color to another, we glue strips of white and blue, 4 of each color. And twist into a curl.



Glue on the left side of the frame.


To fill the voids, we make and glue curls onto the frame. Left is white, right is blue.




Add another blue curl, but larger.


Now back to the bottom of the frame. For decor, we twist a lot of small curls. To do this, cut the strip into pieces of arbitrary size and twist the ends.


Glue the elements so as to fill the entire space.




I always urge not to be afraid to combine various techniques, and in this case I used acrylic outlines for painting. Contour with imitation pearls natural color set a series of points. The size of the dots goes on increasing, from smaller to larger.


In the upper part of the frame, where the curls are blue, draw dots with a contour of a suitable shade.


I drew wavy lines so that one color of the dots smoothly transitions into another.



And here is the result.


Paste favorite photo in a frame, and let it please the eye for many years.

Option 2:

To make a quilling photo frame, you will need the following ingredients:

Thick background paper (minimum 300g/m2)
- less thick paper for flowers (from 120 to 160 grams / m2 - denser is not desirable, because strips of this size will not twist so obediently and smoothly) of two colors. In my case, it's white that will stand out, and a more subtle shade of the background color, which will allow our flowers to blend better with the main color and help bring out the details.
- a paper knife and a steel ruler for cutting strips. Cutting with scissors is a tedious task
- PVA glue
- a toothpick or other device for twisting rolls

We cut strips 30 cm long and 5 mm wide, we estimate the number based on the intended plot. There are many clever ways to cut quickly, such as cutting several layers of paper at once, but with this density (120 to 160) it is quite difficult. Therefore, in order not to be wiser for a long time, I fastened paper for flowers with a notebook sheet in a cage and, whack-whack-whack, moving the ruler through the cells, but first we’ll make a frame, and the most pleasant - for later.

We mark our densest leaf. I recommend that you first draw up a detailed diagram on paper, so as not to cut off the excess, take into account all sizes. I counted on a photo of 13x18, based on these dimensions, we select the width of the frame, mine is slightly wider on the left and bottom. Having finished marking, we cut out a window for the photo, which should be slightly smaller than the photo itself.

Now let's deal with the "pocket" in which the photo will be inserted. The photo paper is very thick and thick, so that the frame does not deform when a photo is inserted into it, we will give the pocket a little width. Stick with reverse side a narrow strip of thick paper, and now you can glue the “pocket” itself, which will prevent our picture from falling out of the frame.

The base is ready

Let's move on to flowers. So, to make a petal, we need a paper strip, which, using a split toothpick (or a more noble tool), is twisted into a tight roll. The roll, in turn, unwinds to a certain diameter, then the end of the strip is fixed with PVA glue and the roll is given the desired shape with the help of fingers. I wash my hands so that there are no offensive ones later dark spots at work. The sections of the strips get dirty especially easily, for white paper this is just a disaster, it is easy to give it a very poor look.

To make the same petals, it is convenient to use a template to unwind the rolls to the same diameter.

I also really like flowers of this shape.

And leaves, of course.

In general, we twist as much as we like, do not forget to create flora of various sizes.
When the main elements are ready, we place them on the frame and glue them. This is not the final version, but the meaning, I think, is clear.

Now we add details until the composition seems complete enough.

The last step remains - we attach a stand on the back for stability.

The frame is ready!

Photo frame made of paper tubes

Option 1:

We will need:

• old newspapers or magazines;
• base frame;
• glue;
• wooden skewer;
• scissors.

Before you make a frame from a newspaper, you need to prepare several dozen tubes. To do this, divide the printed edition into separate sheets, and then wind each sheet, starting from the corner, onto a wooden skewer.

To fix the tube, grease the corner of the sheet with a small amount of glue. Wait until it dries and carefully remove the skewer. Similarly, make a few dozen more paper tubes. In our example, these tubes will need about 55 pieces.

Check if the tubes are long enough to cover the frame. If they are shorter than required, glue the two tubes by inserting one into the other. Now you can start creating a frame from newspaper tubes. Apply to the base frame thin layer glue. You can use a primer if the color of the base does not suit you.

Glue a rectangular frame out of four tubes, the size of which corresponds to the photograph or picture that you plan to place. Carefully remove the ends of the tubes protruding beyond the edges of the frame, and the craft is ready!

Option 2:

We cut the strips for the entire length of the sheet i.e. 30 cm. Band width 5 cm.

Glue is better to use this, not liquid. And you need a wooden stick. We put the stick so that the ends of the strips remain empty, I have 5 cm each. Twisting the tube in this way is not as easy as it seemed to me at first, and I came up with my own method, which I share with you.

First step. We first make a side in the shape of a stick. So it's easier to stick it on. If you do not have such sticks on hand, you can replace them with paper straws. Which are twisted for weaving. For us, the main goal is a frame made of straight tubes (no wraps).

Step 2. Rub the stick on all sides with pencil glue and glue the side to it. We leave it to lie down (the stick and paper should stick together), at this time we glue the next one. And so we made the blanks, proceed to the next step.

Step 3. We make the first turn of the stick by firmly pressing and adjusting the ends of the tube. Then do not try to twist it tightly, you will only wrinkle the paper. You just need to give the shape of a tube. Then, on the floor on the rug, start rolling the sausage (as with dough) at first slightly, then you will feel that it is curling up. Then press firmly and roll until you feel the stick. Try to make the ends in which there are no sticks the same thickness as the center. And yet, if you roll the tube, but it does not twist, then the stick has come unstuck.

Step 4 We fix the tube with clothespins. The clothespins have two sizes of recess, we fix it in the second - smaller. Maybe three clothespins.

Step 5. Glue first between the clothespins, then remove them and finish gluing where the clothespins were. Glued with PVA glue neatly with a needle. The tube is ready.

So I glued the two tubes together. Tubes, if glued in this way, will not lead. They will be even. The glue was applied with a toothpick between the tubes directly from the top. And yet, do not forget to lay all the tubes with a seam at the top - this will be the wrong side.

Only two tubes enter my clothespin, in a large recess.

These are the stripes turned out for the frame. One photo is missing, how I glued 4 tubes. It’s already simple here, cut a strip no wider than 4 tubes and stick it on it.

I needed a frame for this painting. I laid it out as I saw fit, measured the internal size.

I made a mark along the ruler from corner to corner and cut it with a very sharp knife.

I cut out a corner and glued it on.

The frame was constantly measured so that it did not turn out to be a curve.

And here is the corner. Got it!

Bamboo paper photo frame

For a bamboo frame, you need thin, dense tubes of foil or food film. The tubes may differ slightly in diameter - this is bamboo, but in nature it is different.

I cut the tubes, but it seems to me that whole ones are also possible, for example, I saved money, because I had few tubes and I like it better when the frame has a flat side.

First sample. The stretcher was glued together from 2 corrugated cardboard sheets, the front side was covered with a velvet adhesive film, the back with wallpaper. On the top bar you can see that the sizes of the tubes are different.

I glued each prepared “stick” with pieces of some kind of wrapping paper (I found it in the bins) I glued a jute rope under the paper in several places (future bamboo jumpers) the smaller one.

We cover the tubes that have dried from the glue with brown putty (I smeared everything well with my finger, paying attention to the jumpers).

When the tubes dried out, I carefully processed them with fine sandpaper. In places of jumpers I walked with a brush with brown paint and, without waiting for it to dry, she sort of stretched the paint away from the jumpers, thereby making the color transition smooth and natural.

Cardboard photo frames

Option 1:

Create beautiful frames without the appropriate inventory is problematic. So collect minimum set tools. It should include:

• large scissors;
• stationery knife;
• PVA glue;
• simple pencil;
• scotch;
• small scissors;
• fine-grained sandpaper;
• ruler.

Note: it is advisable to get a cutting mat, it is much easier to mark the details of the future frame with it.

If the color of the cardboard for the frame does not suit you, purchase a can of spray paint. To decorate photo frames, use shells, pebbles, glass, rhinestones, beads, etc.

In addition to the basic tools, the following will come in handy: a paint brush with soft bristles, a spray bottle, water and tongs. They will be required to prepare the material for use.

Material preparation

The best material for making DIY photo frames is cardboard. Why? It is cheap and malleable in processing. Every home has at least one cardboard box and glue with scissors.

In its raw form, cardboard is of little use for making a frame for a photograph. His preparation boils down to the following - separate upper layer so that the corrugated part appears.

Sometimes this is not easy to achieve because different types cardboard is made with different amounts of glue and they have different thicknesses.

How to quickly peel off the top layer of cardboard:

Moisten the part of the paper to be removed. Spread the moisture evenly over the surface with a brush. Wait 2-3 minutes for it to soak in. Use your fingers or a knife to pry off the edge of the layer and try to remove as much of the piece as possible. Cut off the rest. Remove dried glue with sandpaper.

The above method applies to big chunks cardboard, for small ones it is sometimes enough to rub the top layer.

Note: spray water more carefully. If you overdo it, the cardboard will get wet. AT best case you have to wait until it dries. At worst, start over.

Instruction

First you need to decide for which photo the frame is created. What matters is not the content, but the size and orientation of the card (vertical or horizontal). Based on this, proceed:

Step #1. Cut out the base.

From big piece cardboard, cut out the base of the frame. Its dimensions should exceed the size of the photo at least twice. Further you will understand why. Using a ruler and a pencil, mark the contours of the future part. Then cut it out with scissors.

Step #2. We make a compartment for photography.

In the middle of the base, draw a rectangle slightly smaller than the photo for which the frame is made. Gently trace along the contour with a clerical knife and cut out the window.

Cut out a rectangle that will cover the photo hole on the back of the frame. Tape the door on one side.

Step #3. We complete the preparation.

Make several cardboard strips of different lengths. Glue four of them around the photo compartment. Use the rest to create the structure of the front. For clarity, look at the figure below.

To make the frame fit snugly against the wall, glue triangles at the corners of the back. They compensate for the thickness of the door and allow the photo frame to hang more evenly.

Making triangles is easy. Cut out one, outlining the outlines with a pencil, and then use it as a stencil.

Step number 4. Decor.

Everything we did before had little to do with creativity. It's time to turn on the fantasy to its fullest. Here is one of the frame design options, but this is just an example, you can come up with your own version.

So, to decorate the photo frame, we use the same cardboard. Take the prepared material with bare corrugation and cut into ribbons. Divide several of them into elements as shown in the figure below.

Next, glue the decorative pieces onto the front of the frame. As a result, we get an asymmetric relief pattern. Such a photo frame is unique and, with the proper approach to manufacturing, will give odds to design counterparts.

Additional photo frame options are as follows:

Traditional photographs have an energy that digital images lack. Enclose them in frames made with your own hands. This will make the captured moments of life brighter, and the design of the room unique.

Option 2:

You will need: corrugated cardboard, self-adhesive paper, scissors, ruler, pencil, colored paper napkins or corrugated paper, stationery stapler, thermo gun, photography.

From cardboard we cut out 2 rectangles 16x20, one 5x15. On one of the rectangles in the center, draw another rectangle, retreating from the edge of 3 cm, the inner rectangle is 10X14.

On self-adhesive paper, lay our rectangle, circle it with a pencil and add 2-3 cm each, as shown in the figure, cut out and carefully glue two large rectangles.

We cut a small rectangle (hereinafter referred to as the holder) from one edge diagonally as in the figure and also glue it over.

To make flowers from napkins, we need 9 napkins, from which we will get 18 flowers.
We cut the napkin into two parts exactly in the middle.

Cut out a circle with a diameter of 5 cm from cardboard. Fold the cut napkin in half and fasten it with a stapler. Let's circle our circle.

Next, cut out and shape the flowers.

We glue the holder with a thermo gun onto a whole rectangle from the glued side.

On the other hand, glue the photo.

We assemble the frame by gluing both parts and flowers.

Wooden photo frames

As you know, wood is an ecological, expensive and refined material.

The tree in any interior emphasizes the aristocracy. By placing wooden product in our house we get a little closer to nature.

Step 1: Materials

You will need a couple of pallet boards for this project, although any other wood will work. In my case, the slightly shabby look of the pallet wood pairs perfectly with the same worn sign, so I used it. If you want to achieve a more polished appearance, then pallets can also be used, just the boards will need to be thoroughly sanded and, for example, varnished or painted.

For rear wall the frame will need something flat, such as MDF, or fiberboard. thin plywood or thick cardboard will also work. The only requirement for the back wall is the dimensions. Dimensions should be slightly more sizes the visible area of ​​the frame, and less than its edges. In other words, it can be about the size of a frame, but a couple of centimeters smaller on each edge.

Step 2: Fix the object of adoration

The frame we have is not quite ordinary, it will not be possible to insert glass into it, for which the photo is placed. Since there is no glass, so that the photo does not fall out, it will have to be glued. I used a car sign instead of a photo, and glued it to the mdf (back wall) with hot glue.

Glue can be anything, but with hot it goes faster.

Step 3: Cut Out the Frame

Now we need a ruler, and basic hacksaw skills (which all men have by default from birth). All you need is to measure the length of the inner edge of the frame on the board, and draw 45-degree corners, and then cut the board along them.

Step 4: Putting All the Pieces Together

I just glued each side of the frame to the back panel with hot glue and that was it. As you can see, there are small gaps between the boards, and I like this look even more.

Step 5: Glue some more

Along the edges of the back wall, I applied another thin layer of glue for extra grip.

Step 6: Frame Mount Hole

The hole for fasteners is made from the back side, and the main thing here is not to make it through.

Step 7: Finishing touches

Tree branches frame

We will need:

• thin branches;
• cardboard;
• glue gun or superglue;
• moss (real or decorative);
• decorative flowers;
• acrylic paints;
• ornamental varnish (optional).

To make such a frame, you need to responsibly approach the choice of material. Try to choose branches of one or two sizes (thicker and thinner). It is better not to take rods with slippery bark, as over time they will begin to dry out, which will make them not too beautiful. Yes, and working with slippery bark is more difficult. Dry branches collected from the ground are best, not plucked from trees.

The blank for the photo frame must be cut out of thick cardboard (and glue several layers together) or plywood. Next, paint the future frame in brown or any other color. The main thing - do not leave it white, as it will not look too beautiful.

Release the branches from excess bark and align. Cut to size frame. Put four thicker branches in the first layer, glue them.

Next lay out another layer of branches. Increase their mass on the photo frame gradually, gluing each one separately. If you are using superglue, which you are not too sure about, fasten the branches with wire together. It is advisable to choose a wire of an inconspicuous color or cover the finished photo frame with spray paint completely so that the fasteners are not conspicuous.

Glue moss around the edges of the frame. If you don't have anything similar, add leaves or buds that can be pre-colored.

Add decorative flowers or beads by painting them with acrylics to make them look like berries. At the end, the craft can be covered with non-toxic varnish for wood processing.

Photo frame of chopsticks for sushi

Option 1:

Making a layout

Arrange the sticks in the form of a lattice. To do this, we put two sticks parallel to each other at a distance of about 20 cm, then we put 5 sticks perpendicularly on them at a distance of 2.5-3 cm.

Preparing the components

We fasten all parts of the layout with threads. Then we repeat the same thing again. We should get 2 lattices, the same as in the picture.

We connect the components

We put the lattices together, and we connect them together.

The photo frame is ready!

We make a loop so that our frame can hang. Then glue the photo with double sided tape. That's all, the product can be placed on the wall!

Option 2:

Frame made of wood chips

Chips can be purchased at construction stores and convenience stores.

This frame will great gift. And you can use it not only for the mirror.

Such a design of the frame would be appropriate for a photo and for a watch, and it is possible to place some kind of beautiful composition from flowers or glass.

Photo frames from improvised means

Pasted decor

You can glue a lot on the frame, everything is determined by the taste and imagination of the master.

Buttons

Photo frames decorated with buttons will look original, especially if you choose them in the same color. However, this is not a mandatory condition. The desired uniformity of color can be obtained using acrylic paint. For example, buttons covered with gold paint will transform beyond recognition, by a lucky chance, an old photo frame that did not have time to get into the trash can.

Beads, rhinestones

Over time, these things accumulate in abundance in every woman. All this can become a unique collection of materials for decorating an elegant frame with your favorite photo with your own hands, it is worth sticking them on a pre-planned pattern, ornament. Tip: you can use whole brooches, beads, beads, pearls, interesting pieces of glass, fragments of broken dishes, mosaic elements.

natural materials

Tastefully decorated frame in natural style always attracts attention. After all, we are all children of nature.

Photo frames from coffee beans, shells

Coffee beans

Coffee beans will come in handy not only for making an invigorating drink, they turn out to be an excellent material for decorating a photo frame with your own hands: they have a wonderful smell, original texture, noble color, they do not deteriorate. The work will not take much time either: it is not so difficult to use a glue gun or PVA glue to tightly cover a standard photo frame with coffee beans, which in a new guise is guaranteed to become a leading interior accessory.

to make the frame made by yourself fragrant, buy anise and star anise stars and find a place for them in the general decor.

shells

This is one of the grateful materials for decorating a photographic frame with your own hands. Seashells are required for decoration. various shapes and magnitude. In addition to shells, it is appropriate to use interesting pieces of glass, sea pebbles and other finds made on the sea or river bank in the inlay.

Photo frames from egg trays

These roses are made from ordinary zhamka cardboard, which is used in bulk for selling eggs.

All you need is a mirror, some egg cartons, scissors, glue and spray paint.

1. Cut out the cells with petals

2. Cut the smaller petals inside the bud, and glue them with the petals slightly offset.

3. Repeat until you have a full rose.

4. Glue the roses on the mirror. The mirror is better to stick masking tape, you still have to paint it.

5. Spray paint, let the paint dry and remove the tape.

Photo frames from foamiran

Materials and tools

To make colorful butterflies, prepare:

• foamiran (plastic suede) 2 mm thick, black and two types of color;
• foamiran thin white and lilac;
• glue "Moment";
• scissors;
• pastel;
• pencil;
• paper;
• cotton buds;
• knitting needle.

Manufacturing technique and photo

On paper folded in half, randomly draw a template with a pencil - half the silhouette of a butterfly, or download the finished picture. You can translate the silhouette of an insect from a book or a children's coloring book.

Cut out the pattern with scissors, lay it on black foamiran, circle it with a knitting needle, slightly pressing on the plastic suede. The material for the base can be dark blue, brown, the main thing is that the top layer is much lighter. Repeat for a blank of a different size and shape.

Fold the paper template in half again and cut out another silhouette that follows the contours of the first one, retreating 2-3 mm from the edge. Repeat steps with another paper pattern.

Cut out all four butterfly silhouettes from foamiran. Decorations follow from thin material different shades.

Tone the upper blank with pastel, typing it on a slightly damp cotton swab. Paint without using strong pressure, the movements should be light to get natural "live" shades. Apply colors symmetrically - in nature, these insects are always mirrored.

Also color in the detail of the second butterfly.

Folding the painted parts in half, arbitrarily cut them into identical parts. Immediately lay out the resulting elements symmetrically on black, otherwise it will be difficult to choose the same later.

The resulting figures, if desired, also cut into smaller ones. The smaller they are, the more interesting the drawing of the wings will turn out.

Lay out the entire drawing of the wings and start gluing the decor to the base one by one. It is advisable to work from the edge to the center, leaving a small black gap between the blanks. This will create a volume effect and make the craft more interesting.

Try to keep all elements glued symmetrically. Remember the perfection of nature.

Now you need to prepare a photo frame. From thick foamiran, cut out two circles that make up the base of the frame; in this master class, the diameter is 22 cm.

In one of them, make a smaller hole (for the desired photo).

Cut out the blank corresponding to half of the top photo frame. Glue it to the bottom base of the photo frame. Glue the front piece on top. Follow the instructions printed on the glue tube.

Glue the resulting butterflies onto the photo frame, choosing good places as in the photo.

Cut randomly small butterflies from colored foamiran for additional decor photo frames and stick them on the front.

Apply the pastel in the manner already described on the frame and butterflies.

Glue a magnet if the frame will be placed on the refrigerator or attach a photo frame holder.

Photo frame with foamiran butterflies is ready to decorate the interior or become a gift.