Operating instructions for the Starline A64 alarm. Overview of car alarms starline a64. The maximum allowable current at the outputs

car alarms Russian manufacturer Starline A series is distinguished by operational reliability and affordable price. Models A62, A64 and A66 are united by two-way communication, a dialogue signal code, as well as the absence of an autorun function in the basic set.

Technical capabilities of car alarms A62, A64 and A66

The main functions that these security systems provide:

• data transmission at a frequency of 433.05 - 434.70 MHz over 128 radio channels;
• the range of the main key fob is 800 m in control mode and up to 2000 m in pager mode;
• the radius of the additional remote control without a monitor is 150 m;
• blocking the engine with a relay;
• managed channels for connecting various additional functions;
• modes "Anti-robbery" and "Panic";
• noiseless car protection;
• the ability to connect autorun and control with mobile phone during installation module StarLine M21;
• protection against radio interference with a large accumulation of cars;
• low power consumption (no more than 25 mA in armed mode).

Compared to the A62, the Starline A64 and A66 models have enhanced functionality and smaller dimensions of parts. Instead of a two-level shock sensor, they are equipped with a tilt sensor with position fixation along three axes, which signals when the car is raised with a jack or moved on a tow truck. Also, the A64 and A66 have a different keyring design, which is much smaller and lighter than the A62.

The availability of a particular function, as well as the cost of alarms, can be found in the table:

• Price. The table shows the price of the basic set. Additional modules are purchased separately.
• CAN module. Allows you to integrate the alarm into the car's digital bus and ensures its more efficient operation.
• Phone control. The GSM module with a mobile chip allows the driver to arm and disarm, enable autostart and control the car's security using a special mobile application.
• Autorun. Remote activation the engine is produced in order to warm it up and create comfortable temperature in the cabin.
• Relay blocking. A wireless relay, which is installed anywhere on the body, does not allow the engine to start in case of theft.
• GPS module. Needed to control vehicle in on-line mode. Usually it is installed together with a GSM antenna.
• Communication control. In older models, you can check the connection by pressing the corresponding key on the remote control transmitter. AT modern models such a check is carried out automatically every 5-10 minutes. If the connection is lost, the system notifies the owner immediately.

Typical malfunctions of car alarms

Starline A62

Starline A64

Starline A66

Instructions for alarms Starline A62, A64, A66

Detailed operating instructions are available in each set of Starline car alarms. If for some reason the driver does not have it, view complete guide you can here:

Instruction starline a62

Instruction starline a64

Independent connection of the security system to the car

To install a car alarm with your own hands, you need to have some experience in working with electrical diagrams and strictly follow the manufacturer's recommendations. standard instruction for car alarms Starline A64, A62 and A66 contains detailed diagram installation and connection of all elements of the system.

Reviews of drivers using Starline A62, A64, A66 alarms

Reviews about the A62 alarm:

New in 2013. Reliable automotive security telematics complex with unscannable dialogue code management, integrated 2CAN-interface, optional GSM, GPS interface, shockproof remote control, 128 - channel noise-immune transceiver with a range of up to 2000 m. super slave For a present.

Advantages of StarLine A64:

Integrated 2CAN interface supports more than 300 car models, including the latest ones. The integrated 2CAN interface simplifies and speeds up alarm installation, minimizing interference with the vehicle's electronics.

Thanks to flexible service channels StarLine A64 alarm system makes it easier to install and implement additional functions without the use of external components.

Anti-theft features:

• Connecting a digital wireless interlock relay StarLine R2 ;
• Adding an additional StarLine GSM/GPS module using just one connector.

Commands in armed and alarm modes:

• Management of additional door locks;
• Additional blocking of the engine (imitation of a malfunction);
• Opening the trunk with the standard alarm off;
• Bonnet lock control (closing);
• Turn on the light alarm when connected to an alarm.

Comfort features:

• Remote control of the starting heater;
• Automatic installation of seats for the owner;
• Automatic return of the steering column to its original position (folding);
• Automatic switching on of the dipped headlights when the car is moving (by lowering the hand brake, pressing the brake pedal).

When the security mode is turned on:

• Automatic folding mirrors;
• Automatic closing of the hatch;
• Light path after arming.

A full range of standard and programmable features provides the car owner with reliable protection and comfort when using a car security system. StarLine A64.

Table of functional characteristics

Based on the StarLine A64 system, you can build a reliable security complex, which includes:

Equipment:

• central signaling unit
• 1 keychain with two-way communication with LCD
• 1 keyfob with two-way communication without LCD
• transceiver
• hood button
• Light-emitting diode
• service button
• set of wires
• installation instructions
• user manual
• user memo
• block relay with block

Specifications:

The maximum allowable current at the outputs:

Thanks for your choice. Please fill out the form. We will contact you within 24 hours.

Fields marked with an asterisk are required

Description

	TELEMATICS Optional GSM-GPRS, GPS-GLONASS
	FEDERAL SUPPORT SERVICE Russia 8-800-333-80-30 Kazakhstan 8-800-070-80-30 Ukraine 0-800-502-308

Advantages of StarLine A64:

Anti-theft features:

Comfort features:

Instructions

Delivery

In Moscow within the Moscow Ring Road:

• By courier free (with an order amount of more than 5,000 rubles)
• By courier 300 rubles. (when the order amount is less than 5,000 rubles)

Moscowoutside the Moscow Ring Road and Moscow region (up to 40 km from the Moscow Ring Road):

• By courier 300 rubles. (with an order amount of more than 5,000 rubles)
• By courier 500 rubles. (when the order amount is less than 5,000 rubles)

Our company is constantly improving the level of customer service, so we offer order delivery services, which is carried out through our own courier service. The cost of the service depends on the amount of the order and the delivery address specified by the client. The presence of our own transport resources allows us to deliver deliveries to the specified address in a timely and efficient manner. If you have individual wishes regarding the exact time of arrival of the courier, be sure to indicate this, and we will definitely find the best solution!

To the regions of Russia:

• Russian Post. The cost is calculated automatically when placing an order on the site.
• Courier service SDEK (delivery to the door). The cost is calculated automatically when placing an order on the site.
• transport company" Business Line". The list of delivery cities and tariffs can be found atwww.dellin.ru
• Transport company "PEK". A list of delivery cities and rates can be found atwww.pecom.ru

* All long-distance shipments are insured by us upon shipment, you don’t have to worry about the safety of the goods

Available pickup goods to the address: Moscow, Golovinskoe shosse 1, after preliminary reservation.


• • Cash upon receipt of goods (only for courier delivery and pickup)
  • Online payment bank card(produced when placing an order on the site)
  • Online payment from Yandex.Money wallet (performed when placing an order on the site)
  • According to the receipt (the receipt is generated automatically when placing an order on the website). Payment can be made at any bank branch using the details specified in the receipt.
  • Cash payment by code through Svyaznoy, Sberbank and other terminals, Svyaznoy, Euroset communication stores. Code for payment and detailed instructions will be formed upon completion of the ordering on the site

  * Online payment by bank card is made through the Yandex.Checkout service without commissions, via a secure connection with maximum protection of your personal data

Installation

The installation of StarLine systems on various car brands may have its own characteristics, requiring deviations from standard scheme installation (for example, if there is digital bus CAN in the vehicle, separately connected door switches, etc.) StarLine installation should be trusted by professionals and produced in specialized installation centers with experience in installing car alarms.

SAO northern administrative district of Moscow


• Certificates

  An important criterion for choosing a car alarm is its complete safety in relation to vehicle systems, as well as the absence of radio frequency interference during operation. The presence of official certificates of conformity for the entire list of products is an additional confirmation High Quality car alarms, GSM / GPS modules and security systems presented in the catalog of our company.

  

New in 2013. Reliable automotive security and telematics system with a non-scannable dialogue control code, an integrated 2CAN interface, an optional GSM, GPS interface, a shock-resistant remote control, a 128-channel anti-jamming transceiver with a range of up to 2000 m. Super Slave as a gift.

Advantages of StarLine A64:

The integrated 2CAN interface supports more than 300 car models, including the latest ones. The integrated 2CAN interface simplifies and speeds up alarm installation, minimizing interference with the vehicle's electronics.

Thanks to flexible service channels, the StarLine A64 alarm system makes it easier to install and implement additional functions without the use of external components.

Anti-theft features:

• Connecting a digital wireless interlock relay StarLine R2;
• Adding an additional StarLine GSM/GPS module using just one connector.

Commands in armed and alarm modes:

• Management of additional door locks;
• Additional blocking of the engine (imitation of a malfunction);
• Opening the trunk with the standard alarm off;
• Bonnet lock control (closing);
• Turn on the light alarm when connected to an alarm.

Comfort features:

• Remote control of the starting heater;
• Automatic installation of seats for the owner;
• Automatic return of the steering column to its original position (folding);
• Automatic switching on of the dipped headlights when the car is moving (by lowering the hand brake, pressing the brake pedal).

When the security mode is turned on:

• Automatic folding mirrors;
• Automatic closing of the hatch;
• Light path after arming.

A full range of standard and programmable functions provides the car owner with reliable protection and comfort when using the StarLine A64 car security system.

Car alarm STARLINE A64 main features:

The Starline A64 car security and telematics system is based on a dialogue code for signal encryption, as well as a 128-channel narrow-band transceiver. This allows the alarm to work effectively even in conditions of extreme urban interference.

[ Hide ]

Specifications Starline A64

Description of the main specifications car alarms Starline A64:

• the level of the carrier frequency of the communication channel is 433-434 MHz;
• the maximum range of the pager when sending signals - 800 meters, when receiving them - up to 2 km;
• the operating range of the spare communicator varies around 15 m;
• the ability to control the protection system at temperature environment from -50 to +85 degrees;
• impact controller belongs to the category of integral three-axis devices;
• nutrition security complex carried out from the on-board network with a voltage of 12 volts;
• for installation in pagers, AAA and CR2450 batteries are used.

The Auto Goods Unpacking channel spoke in detail about technical properties and parameters of modern security Starline systems A64.

Equipment

Overview of devices and elements included in the Starline A64 delivery:

• service user manual for installation and configuration, allowing you to configure all functions;
• consumer memo;
• warranty card;
• the main microprocessor device in a black rectangular case;
• batteries for use in the main and additional consoles;
• main and spare pagers;
• three relays equipped with pads;
• limit switch for mounting on the hood, two self-tapping screws for its fastening, as well as a terminal clamp for connecting to ground;
• transceiver module equipped with an antenna adapter;
• adapter for connecting additional controllers;
• LED light that allows you to determine the status of the security complex;
• button to enter the emergency mode of control and maintenance;
• a set of wires with connectors for signaling connection.

Siren, as well as limit switches for doors, are not included in the A64 package, these devices must be purchased separately.

Complete set of alarm system Starline A64

Key Features

Car alarm Starline A64 has extended functionality:

1. Possibility of implementation auto start car engine at additional connection modules M21 or M31. Enabling this option is possible on vehicles with a diesel or petrol injection system, regardless of the type of gearbox. It can be set automatically or the start is made by the command of the car owner, which is sent from the pager.
2. Models of Starline A64 Dialog and 2CAN security systems allow determining vehicle coordinates using GPS and GLONASS satellites. This feature is optional, for its operation, the owner of the “signaling” must additionally install a GSM module (preferably from the Starline manufacturer). These models differ from each other in that the second one has a digital CAN interface. It allows you to connect the protection system to the appropriate bus with minimal interference with the regular wiring.
3. The presence of a preheater control system. Such devices are equipped with diesel power units.
4. The ability to automatically change the position of the driver's seat. This option can only be enabled on cars that are equipped with electronic system adjustments. Additional flexible channels are used to control devices.
5. The function of automatic activation of low beam headlights at the start of the ride. The user can adjust the operation of the optics when lowering the "handbrake" or when depressing the brake pedal.
6. The ability to control the anti-theft system using a smartphone. This is allowed when installing an optional GSM module. Using the device, you can configure the transmission of information about the security status to the phone.
7. Low power consumption feature. car battery will be able to keep the charge for 60 days with the alarm turned on.
8. Usage power keys(SC), the use of which makes it possible to ensure silent operation of the control module. This opportunity allows to provide reliable protection of contacts against possible short circuit. SC is an author's development of the company, which allows to reduce the risk of fire hazard.
9. Slave mode. With it, the car owner can control the anti-theft system using the remote control from the standard central lock. Devices must first be synchronized.
10. Possibility to connect additional controllers for interior protection. I mean the slope. In the control unit, special connectors are provided for their connection.
11. Blocking the power unit. For this, special relays can be used or digital devices. The latter are connected additionally.
12. Switching on the protection of the vehicle with the engine running. You don't need to leave the key in the ignition.
13. Anti-theft option. Its essence is to block the engine if the car has robbery. Depending on the readings of the brake sensors or at the command of the owner, the power unit will stop and the vehicle will not be able to continue moving. The stop is made after 30-60 seconds, during which time the hijackers usually leave the crime scene at a safe distance for the user.
14. Availability of an automatic control system for the operation and condition of sensors. When faulty devices are detected, the microprocessor module disables them, sending a warning to the car owner.
15. Saving information in memory about triggered alarm modes with the possibility of their further viewing.
16. Ability to remotely disable controllers and regulators when machine protection is enabled. Only the warning zones of the sensors can be deactivated.
17. The presence of two different sound modes of the pager, as well as the option of vibration notification.
18. Blocking pager buttons.

Details about functionality anti-theft systems Starline A64 in his video told the channel "AvtoAudioTsentr".

Advantages and disadvantages

Advantages:

1. Reliable operation of the alarm in any conditions. This refers not only to interference characteristic of large cities, but also to temperature differences.
2. Large actual range of pagers. Many manufacturers purposefully increase this figure, which in practice can be lower by 50% or more. In the case of the Starline A64, the range in fact practically corresponds to that indicated by the developer.
3. Easy to install and connect. The instruction includes detailed wiring diagrams, with the help of which the consumer can connect all the elements and contacts on his own.
4. Great functionality at a relatively affordable price.
5. Shock-resistant case of a pager. Thanks to this, the device will not fail in case of a fall or other physical impact.

1. Rapid wear of the key fob despite high strength corps. In accordance with user reviews, on Starline A64 pagers, control keys eventually fall down, which will later have to be repaired.
2. Difficulty of setting slave mode. In addition, when using a regular communicator, the system may not function correctly.

How to install Starline A64?

The Starline A64 alarm is set as follows:

1. The control device is mounted discreetly in the car interior and fixed using self-tapping screws or plastic clamps. You can choose to install free space behind the glove box or instrument cluster. This unit is equipped with a temperature sensor, so it should not be placed near heat sources such as heating system blowers.
2. The transceiver module with antenna is placed away from metal products. The device is equipped with a tilt and impact controller, so it is not allowed to install the adapter on a plastic cladding. Also, the manufacturer does not recommend placing the device on windshield if it has a tinted film on it.
3. The LED bulb is fixed on the dashboard in the cabin.
4. The siren is placed under the hood of the car, protected from external influences place. If the device is equipped with an autonomous battery, then the user must provide access to its keyhole during installation. On the connection wire, install safety device rated 3 amps.
5. The hood and all doors are equipped with limit switches. Installation of these devices is not allowed on drains. The laying of wires from the "limit switches" is carried out under decorative cladding, all electrical circuits are pulled to the processor device. With the hood and doors locked, there must be no access to the switches.
6. If a GPS antenna is additionally installed, then it must be connected to the five-pin block X10. Fixation of the device is carried out by means of double sided tape, and its body is placed horizontally. Before fixing the module, it is recommended to check its operability and communication quality in advance.
7. Any additional equipment, including modules, must be connected to the three-pin X4 connector on the processor unit. The cable included in the delivery is used for connection.
8. In a hidden way, a key for entering the “Jack” service mode is placed in the cabin.
9. When installing the P2 radio relay, it is necessary to immediately program this element. To do this, select the appropriate blocking option in the pager settings and leave the programming menu. After that, the “GDN” contact of the device is connected to the car body and, with the ignition off, press the “Jack” button 7 times. The key is rotated to the “On” position and within five seconds the user must connect the black wire to the switch power line.

The Autosound Base channel spoke in detail about the mistakes that can be made when self-assembly security complex A64 on the car.

User manual

Before using the alarm, you must make sure that it is installed correctly. To do this, activate and deactivate the protection mode and check the operation door locks.

How to set up autorun?

Features of changing the parameters of the automatic start of the motor option using additional Starline M21 and M31 modules:

1. To activate the function, a message with the text “0066200000000” is sent to the phone number in the block, and “0066100000000” is sent to disable it.
2. Before setting the option, it is recommended to select the type of transmission installed on the vehicle. For vehicles with manual box transmission, the command “0066010000000” is transmitted, with automatic - “0066020000000”.
3. The duration of the starter mechanism scroll is configured by sending a message in a similar format. For 0.8 s - "00660001000000", 1.2 s - "00660002000000", 2 s - "00660003000000", 6 seconds - "00660004000000".
4. The control of the operation of the power unit of the car can be implemented according to the readings of the generator device or tachometer. In the first case, a command with the text "00660000010000" is sent, in the second - "00660000040000".
5. The user can set the duration of the machine's engine operation after the start. To make this parameter 10, 20 or 30 minutes, the messages "00660000000100", "00660000000200" and "00660000000300" are transmitted, respectively. If you want to remove time limits, you must send a command with the text "00660000000400".
6. For vehicles equipped with a Start/Stop ignition system, the number of times the start button is pressed can be adjusted. To select one or two signals, messages "00660000001000" or "00660000002000" are transmitted, respectively.

CAN interface programming

Connecting and programming the CAN interface is necessary for control additional equipment in the car. This refers to electric mirrors, seat adjustment, power windows, sunroof. To connect devices, you do not need to cut into the standard wiring, you just need to connect to the connector.

To enable work CAN bus Starline A64, the following steps are performed:

1. Nutrition anti-theft complex turns off. If the CAN wire was connected to the control unit, then it must also be disconnected.
2. The service key is pressed. At the moment of holding it, the alarm siren will work five times.
3. The button is released after the last sound pulse. Four more signals will signal the entry into the digital interface setup mode.
4. Then you need to enter private idintifier vehicle. All car models that can work with the tire have unique four-digit numbers. They can be found directly in the service manual for the alarm or on the official website of the manufacturer.
5. Using the service button, you need to go to the first section of the settings menu, for this the key is “clicked” once. Then it is pressed the number of times corresponding to the first number of the car number. In confirmation, the siren will work several times, this will happen two seconds after the sign is indicated.
6. Similarly, after the beep, the remaining characters are entered immediately. After the last digit has been confirmed by the control unit, either two or four beeps will sound. In the first case, the vehicle number was entered successfully; in the second, it was not.

Key fob control

Before using the Starline A64 pager with feedback or without it, batteries must be installed in the device. Batteries are inserted into a special compartment hidden behind the back cover of the remote control.

Designation of symbols and buttons on the key fob

Correspondence of keys on the main and additional pagers:

Controls on the main and spare communicators Starline A64

Indication of symbols on the device screen:

1. Icon for diagnostics of the state of the anti-theft complex.
2. Service mode for servicing the alarm.
3. Option to deactivate the impact controller by levels - warning and alarm.
4. Activation of silent protection mode.
5. Arming indicator with silent alerts and warnings.
6. Full protective function of the car with loud sound pulses.
7. Vehicle search option.
8. Activation of the "Panic" mode.
9. Calling the car owner from the salon.
10. Activation of the second additional channel.
11. One of the door locks, hood or luggage compartment of the car is open.
12. Started engine icon.
13. Anti-robbery mode is enabled.
14. Indication of the discharge of the battery in the pager.
15. The "handbrake" in the car is not tightened or the brake pedal is depressed.
16. Display of the current time.
17. The ignition system is on in the car.
18. Indicator of a triggered shock and sensitivity sensor. The warning or alarm level of the device may have been activated.
19. The alarm is activated.
20. Pager vibration.
21. Communication channel indication for transmission of control commands.
22. The car door locks are locked or open.
23. The operation of the zero additional channel, by default it is set to open the tailgate.
24. First additional channel alarm management.
25. Indicator silent security or protection of the car with sound accompaniment.

Designation of icons on the display of the Starline A64 control device

How to program a key fob?

Using all the functions of the Starline A64 anti-theft complex is possible only after linking the pager.

To complete the task, do the following:

1. While the ignition is off in the car, you must press the button to enter the emergency mode seven times. Upon successful login, the siren will sound.
2. On the pager, the first and second buttons are "clicked" at the same time. This step is repeated for each prescribed communicator. The time interval between entries should be no more than five seconds. Upon successful binding, the siren should sound.
3. To leave the programming menu, the vehicle's ignition system is switched off.

How to use guard mode

Features of car protection control with Starline A64 alarm:

1. Button 1 is used to enable the option. It can also be activated by moving the cursor to the position of the indicator with two notes on the screen. After selecting the icon, the third key is pressed. The activation of the security mode will occur if all doors, hood, trunk are closed and the limit switches are in good condition.
2. If you want to enable silent protection sound signals, the display cursor moves to the single-note icon. After selecting the indicator, button 3 is pressed. The headlights of the car will work, a siren will emit one quiet signal.
3. To activate the silent protection on the screen, the cursor must be moved to the position of the indicator with a crossed out horn. The diode lamp will start blinking, the corresponding icon will be displayed on the display of the pager.
4. To arm the guard without accompanying signals, the first key is “clicked” twice.
5. Activation of protection on a car with a running engine is carried out with the hood locked. The gear lever must be set to neutral (for manual transmission) or in "Park" (for "automatic"). To turn on the protection, you need to move the cursor to the indicator with one or two notes and "click" on the second key. Then the key is removed from the ignition lock, the driver leaves the passenger compartment and presses the first button.

In the absence of a remote control, protection is controlled as follows:

1. The door opens with a key. The control element is inserted into the lock, the ignition is activated. This will cause the LED light to blink.
2. The button to enter the emergency maintenance mode is pressed three times. The ignition system is switched off. From this moment, the alarm will start counting the 20-second interval, after which the protection will be activated.
3. The driver leaves the car and locks all the door locks.
4. To further disable the protection, the user turns on the ignition and enters a personal password using the service button. After the last digit of the code has been entered, security mode is deactivated.

The Autoelectro channel spoke about the operation of the Starline A64 anti-theft system installed on a Mitsubishi Pajero car.

Service mode setting

A64 Function Control Features:

1. To control the battery voltage and the alarm status, double-click the third button of the communicator. It is possible to move the cursor on the remote control screen to the position of the corresponding indicator. After selecting it, you must "click" on the key 2 or 3. Information regarding the state of the vehicle and other parameters will be displayed.
2. To carry out the “Search”, the first button of the pager is pressed until a signal appears, and then it is pressed briefly. The device will emit a melodic pulse. The siren, as well as the headlights of the car, will work six times.
3. To temporarily deactivate the sensitivity controller, the second key fob key is “clicked” twice. It is possible to move the cursor on its screen to the position of the hammer icon. Then the button 2 or 3 is briefly pressed. The armed mode must be activated in this case. The warning zone of the regulator will be disabled.
4. To re-activate the shock sensor when the protection is on, the second key is pressed twice. You can move the cursor to the indicator in the form of a hammer and press the button 2 or 3.
5. If it is required to deactivate the operation of the tilt controller, button 2 is pressed when the security is on, and then “clicked” briefly. To return the device to a working state, similar actions are performed.
6. To adjust the sensitivity parameters of the shock sensor, key 3 is held down for a long time, and then once briefly. The security mode, as well as the ignition system in the car, must be turned off. Controls 2 and 3 change values. The transition from setting the warning level to the alarm level is done by pressing the third key.

Setting a personal management password

To assign a new code (example - 26) for Starline A64, the following steps are performed:

1. The user enters the option programming menu. On the communicator, you must select function number 9, and its value is 3. This indicates the setting of a two-digit code.
2. The button for entering the service mode is pressed four times. The ignition is activated. Upon successful entry into the programming menu, the anti-theft system will work with four siren signals.
3. Key emergency mode is pressed once. The remote control screen will prompt you to enter your personal password. A box will appear with a "P-" indicator.
4. The second pager button is pressed because the first code value is 2. The user can assign any combination in the range from 1 to 66. Characters 1, 2 and 3 are assigned to the first, second and third keys of the communicator. Signs 4, 5 and 6 are defined by the same controls respectively, only the first press must be long and the second short.
5. Then the first button is "clicked". The siren will work with two beeps - this indicates the readiness to accept the next sign.
6. Character 6 of the password is entered. The third pager key is first held down for a few seconds, and then “clicked” briefly.
7. The ignition system is turned off, this will allow you to exit the programming menu. The car's headlights should flash three times.

Download the installation and operating manual in PDF format

You can download the technical documentation for the installation and control of Starline A64 systems using the links:

Possible malfunctions and ways to eliminate them

The need to repair the Starline A64 alarm may arise with the following malfunctions:

1. The system stopped responding to commands sent by the user. To fix the problem, you first need to check the battery in the pager and replace it if necessary. It is necessary to disassemble the communicator and determine the failed elements - damaged contacts and buttons need to be soldered.
2. The system does not perform functions correctly. The problem may be related to the incorrect operation of the pager as a result of moisture getting on it. To fix the problem, you need to disassemble the remote control, remove the board from it and dry it (do not use the stove, hair dryer or battery). It is recommended to remove the remaining moisture with a dry cloth. It will be useful to clean the circuit from dirt and dust.
3. The alarm responds to commands, but the range of the pager has significantly decreased. If the problem is not related to the discharge of batteries, then most likely it is due to interference in the area. They may come from manufacturing enterprises, transformer substations. To disable the protection mode, you need to get as close as possible to the transceiver installed in the car.
4. Starline A64 does not block all door locks. If the limit switches themselves are OK, then the user must “ring out” the wiring to detect defects with a multimeter or other tester. Damaged electrical circuits must be replaced, as well as cables on which the insulation has worn out, since this can cause current leakage. When laying new wires, it is recommended to additionally wrap them with electrical tape to ensure their higher reliability and prevent rapid wear.
5. The anti-theft system does not function correctly, independently turns off and turns on the protection. Most often, the cause of the malfunction is related to the operation of the control unit. The firmware in the device could “fly off”, reconfiguration will be required to fix the problem software using a computer. The failure of the microprocessor is often due to regular exposure to vibration during movement, as well as moisture.

How much does the Starline A64 alarm system cost?

Approximate purchase prices anti-theft system A64:

Video

User Stepan Putyatin briefly spoke about the features of flashing the Starline A64 anti-theft system.

In fact, a lot depends not so much on the specific alarm model, but on how and by whom it is installed. I was lucky to have a professional installer in my acquaintances, so the signaling on the Kia Ceed SW is installed as it should. That is why it was chosen A64- seems to be one of the simplest models in the line Starline, but providing maximum protection with proper installation.

Reliable automotive security telematics complex with unscannable dialogue control code integrated 2CAN-interface, optional GSM, GPS interface, shockproof remote control, 128 - channel noise-immune transceiver with a range of up to 2000 m. super slave For a present.

For the same reason, he refused autorun. It has its pros and cons. But I believe that the main purpose of the alarm is the safety of the car. And any additional features should not interfere with this.

Beyond the List basic characteristics, you can expand the capabilities of this signaling with additional GSM modules or GPS. So if you want, you can make from it complete analogue and more sophisticated models.

And so the principle has everything you need. It is convenient to have the Slave mode, which allows you to use the standard key in addition to the A64 key fob. It is also possible to transfer the alarm to the service mode - i.e. actually temporarily disable protection. I used this opportunity several times, leaving the car in the service. For example, at TO-1 in the Korea Car showroom.

The keychain is strong, the buttons are comfortable - they are not accidentally pressed.

The disadvantages include low sensitivity Although for me this is not such a minus. If the car squeaks from every passing truck, that's not good either. And again, the main function is the immobilizer. The hijacker should not be able to leave the car, even if he manages to get into it.

Even in the features, "record energy efficiency" is indicated, but I did not notice anything special in this regard. The battery charge sags for a week or two of parking, especially in winter. Yes, and the battery keychain itself eats be healthy!

I am calm and confident enough that my car is as protected as possible with StarLine alarm system A64. But remember that absolute protection does not exist by definition. Any system can be bypassed. Therefore, you should not lose vigilance, no matter what alarm you set.