Decoupage tea house: do-it-yourself kitchen craft. Decoupage of a tea house: a detailed description of the design and decoration. Overview of the best ideas and options for their combinations DIY tea houses decoupage

A tea house is a cute accessory that will add coziness to your kitchen and will be remembered by your guests for a long time. Looks like small house containing tea bags.

Such a house can be purchased at the store, or you can make it yourself. Usually, a wooden blank is used for this, which is sold in needlework stores.

And most in a simple way Decorate a tea house is decoupage.

Decoupage is a decoration technique in which images on paper are pasted onto wooden or other surfaces.

Decoupage tea house, the master class of which we will now demonstrate, can be done in two ways.

Simple decoupage of a tea house

For work we need:

Wooden blank.
Decoupage napkin or decoupage card with a suitable image.
Primer
Acrylic paints
PVA glue

We take a wooden blank.

Processing if necessary sandpaper, cover with a primer. After drying - cover with white acrylic paint.

Separate about 2/5 of the height and glue masking tape. top whiten again.

Please note: to make the strokes more accurate, they must be done vertically, along the entire length of the surface to be decorated.

After the top is dry, you need to stick masking tape on the other side and paint over the bottom in dark color. Here, umbra is used for this. On top - a little gold acrylic, which is then rubbed with a candle. This is done in order to get an imitation of attrition, which is typical for old things.

Now you should paint the roof of the house in the color of its base. To get natural shades, you can follow the following sequence: one coat of paint, then a little gold paint. We rub the gold with a candle and cover it with a second layer of paint.

If you add a little umber to the white, you get a nice creamy shade. We cover the top of the house. Optionally, you can paint the inside of the house. Don't forget to paint the bottom!

We turn to the decoupage of the tea house itself.

We cut out (or better, tear out) the necessary elements from the napkin, glue them with PVA glue. We varnish the entire house.

The house can be decorated with lace or ribbon and it is ready!

Volumetric decoupage of a tea house

Volumetric decoupage technique is called in a different way ambient technique.

"Ambiente" - literally translated as " Environment”, but in decoupage it is a “protruding drawing”. That is, this is such a decoupage technique, as a result of which the image is voluminous, with protruding elements.

So, to make a tea house using the volumetric decoupage technique, you will need the following materials:

wooden blank
Embossed acrylic paste (thin)
A palette knife is a special knife. Instead, you can use a flat spatula (for example, from a manicure set)
Acrylic paints (here colors such as cadmium red and yellow, ultramarine, burnt umber, chromium oxide, English red)
Decoupage napkin or decoupage card. In this master class, a rice map with elements of architecture was used
Spray lacquer (preferably matte)
Acrylic varnish (also matte)
3-D gel
Stencil for imitation tiles
Glue (PVA or decoupage).

First, as usual, we prime our workpiece.

We tear out fragments from a napkin or rice card that will be used in the decoupage of a tea house. The indentation from the edge should be about 1.5 cm.

We stick architectural details on the house and flower pots. Glue only the middle, do not glue the edges yet!

Using a palette knife, apply relief paste under the edges. We give it the desired shape, and then glue the edges of the napkin. Thus, a volumetric element is obtained.

We make an imitation of brickwork on the walls using paste. Individual bricks can be drawn with a toothpick.

On the roof we apply the paste through the stencil. It turns out an imitation of tiles.

Then we paint the house, namely the walls and brickwork. At vine you need to draw in detail the foliage and antennae.

You can paint the house with other elements, for example, add a street lamp and cracks on the walls (as if the plaster had cracked).

We paint the cover on the tiles with "English red" paint.

From ancient times tea ceremony was important event Everyday life. This tradition is rooted in ancient japan, where beautiful geishas have turned the usual use of tea into a whole rite. For the ceremony, a special Japanese tea house was used, which was adapted specifically for tea drinking. In Russia, tea drinking was also accompanied by long gatherings and conversations. Then it was believed that such things bring people together very much.

To begin with, the table was covered with a starched white tablecloth, a large shiny samovar was placed in the center, and all kinds of sweets and pastries were placed around it. This tea party lasted more than one hour.

In the past, loose leaf tea was very popular, but now it is much more convenient and time-saving to use tea bags. Of course, a box of tea on dining table- the spectacle is unaesthetic, so the idea of \u200b\u200bcreating a house for tea appeared. With the help of a simple master class, anyone can make a tea house with their own hands, using decoupage and decorating the house with decor.

To make such a cute tea bag house out of wood or cardboard, necessary schemes, or detailed drawing, where all sizes are indicated, it is easy to find and download on the Internet. We will step by step analyze what to do after the house is assembled according to these schemes - how to give it the proper appearance so that it can not only be used for its intended purpose, but also decorate your table setting? So that there are no difficulties even for beginners - assembly manual, photo gallery finished houses, as well as an interesting and useful video.

The easiest option is to assemble a structure from improvised material, cardboard. In this tutorial, you can use any cardboard box: postal or from household appliances. In addition to the box, we will need some materials and tools:

stationery knife;
leg-split;
glue;
ruler;
simple pencil.

You need to start like this, using a pencil and a ruler on cardboard, draw future details: 4 rectangles 20/9 cm, 1 rectangle 10/6 cm and 4 squares 10/10 cm. In one of big parts you need to form a "door" from which tea bags will be taken out. To do this, draw a semicircle 5 cm high and 1 cm indented from the edges, cut it out. In addition, it is necessary to cut out strips: 20/3 cm - 4 pcs. and 9/3 cm - 4 pieces, as well as two triangles to cover the front and back of the roof. These parts are best made from thick paper or thin cardboard.

Now we bend the cut thin strips along exactly in the middle and glue 4 walls of the future house with their help. Next, we form a three-dimensional triangle from a 9/3 cm strip and glue it to it on both sides in a 10/10 cm square - we get a roof. When gluing squares, you can put a loop between them for convenience. Now we cut out the triangles to close the roof with them from the front and back sides. Lastly, the bottom is glued - it is attached to the walls with the help of short strips.

For aesthetics, you need to close all cut cardboard edges with twine. The roof can be decorated with cardboard tiles, and with a clerical knife, cut out a window on the “second floor” and make it with partitions, suspension or curtains. Tea bags will be "populated" through the roof.

This simple step by step tutorial answered the question of how to make a tea house with your own hands without decorations. Similarly, you can make such a blank from plywood by fastening it with nails. Further design should be thought out and selected based on kitchen interior and fantasies of the master. You can bring any idea to life and the blank will become an Italian villa, Santa's New Year's house, a hut of the seven dwarfs or a tower with Rapunzel sitting in it.

Gallery: do-it-yourself tea house (25 photos)

Tea house decoupage master class

In the Middle Ages, decoupage was considered a technique for the poor, because with its help old things were updated: dishes, furniture, caskets and other household items. Decoupage is described in detail in this master class. cardboard house. For registration we need:

To make the pictures on the house look bright, the cardboard base is coated with white acrylic paint in 2 layers. All unnecessary layers are separated from the napkin and only the part with the pattern remains. The walls of the house, on which the napkin will be glued, are properly smeared with glue. A napkin is glued from the center to the edges in order to avoid bubbles and bumps as much as possible. A layer of glue is also applied over the drawing. Subsequent decoration at your discretion: empty parts can be covered with small pieces eggshell, add a drawing with acrylic paints or imitation of brickwork.

There is one more decoupage option, where the picture is applied using a paper file. Here the desired layer of napkin is placed on the file front side down. Then the picture is wetted with water and glued to the house from the center to the edges with light pressure. The file is removed, and the picture remains glued evenly, without swelling.

On the roof, using a stencil for tiles, a relief paste is applied. The tiles are covered with red acrylic paint, and after drying, they are darkened with umber for a natural effect. When the roof dries, apply a matte spray varnish. 3D gel is used on the windows to reflect light. The final composition is processed with matte acrylic varnish, which allows you to fix all the details and paint.

Volumetric decoupage technique

External decor is made using embossed acrylic paste and allows you to add volume to individual elements with your own hands.

To make windows and doors voluminous, you need to glue the drawing only in the center, and first apply relief paste under the non-glued edges with a palette knife.
You can use the paste on the walls, and then form the bricks with a toothpick.
Stick flowers in pots along the walls of the house and add volume to them. Only in this case the paste is applied in the center.

Exist great amount master classes in this technique. She "revives" the creation and gives it a fabulousness, like an enchanted house.

tea house design

The base and decoration should match the interior, occasion, person, if it is a gift. It would be a good idea to do do it yourself New Year's tea house in garlands and snow as a gift to a friend or in the form of a skyscraper for use in the office. Getting a tea bag out of such a designer creation will be a pleasure.

If a manufactured copy conceived for personal use, then you can add a set cutting boards, napkin holders with decoupage of the same theme. With an Italian villa or a house from Provence, new chair covers or kitchen towels with hand embroidery. There are an infinite number of options for decorating a tea house - fantasize, think over, embody!

The master class was held by Oksana Lebedeva.

Many housewives are trying to equip their kitchen, add comfort and warmth. This requires extraordinary, but functional things. One of them can be a tea house for storing tea bags.

Materials:
preparation of a tea house;
putty;
acrylic paints (white, ocher, red, burnt umber, gold);
acrylic lacquer;
PVA glue;
table napkin made of bamboo straw;
three-layer napkin;
decorative element butterfly;
stencil.

Instruments:
flat bristle and synthetic brushes;
sponge;
toothbrush and stick;
sandpaper No. 150, 180, 600, 800;
file;
palette;
glue "Moment Crystal".

How to decoupage a tea house.

We glue the structure. We strengthen, primed with a mixture of white acrylic paint, putty and PVA glue (proportion 1: 1.1). Apply with a stiff bristle brush to create an uneven texture. We dry. Then we cover the house with white acrylic paint and dry it again.

We create the main background of the house. To get a creamy shade, mix white paint with 2-3 drops of ocher color (you can add ocher or sienna acrylic paint instead).

We dilute the resulting shade to a "kefir" state. The resulting water-color mixture is applied with a soft synthetic brush. We dry.

We tear out the necessary motives from the napkin, glue them using the “file method”. Place the napkin face down on the file. Pour a little water on top (you can do this with a spray bottle). Gently spread the napkin over the water with your fingers or a soft brush, after which excess water merge from file. We turn the file over with a napkin down and put it on the surface to be decorated.

Smooth well. Carefully lift the file (so as not to pull the fragments of the napkin), remove it with a towel excess moisture along the edges of the motif. You need to try to lay down the napkin without wrinkles. We fix the motif with glue. We act from the center to the edges of the motif, using a soft brush, and then you can slightly smooth it with your finger (it is important that your fingers are wet - there is less risk of pulling the napkin along with you). Dry well.

Glue floral motifs below and above the windows. Dry and fix 1-2 layers acrylic lacquer. After drying, level the surface with fine-grained sandpaper (at least No. 600).

We prepare the paint for the stand and the roof: we slightly muffle the brightness of the red with burnt umber. We paint these details of the house. After drying, the stand is varnished in two layers and dried well.

We also paint the edging of the walls and windows with a red-burgundy color. The lines are thin, so we act carefully with a flat brush and, where possible, a small sponge. With light tangential movements, we also pass along the edges of the walls, slightly “dirtying” them.

Apply the same paint stencil drawing down below. We fix the stencil with masking tape. Use a hard bristle brush. We hold the brush at an angle of 90 degrees and “drive in” the paint with tamponing movements. Wipe off excess with a cotton swab.

Add a light splash. toothbrush dip in water, apply a little paint, put it at an angle of 90 degrees to the surface. With a stick, we draw along the brush towards ourselves, while moving along the surface. We fix with a layer of acrylic varnish. Lacquer is applied with a flat synthetic brush. We dry.

Since the layers of paint made the walls thicker, we file the holes a little with a flat file and insert the parts into place.

We make thatch roofing. We cut the sticks along the height of the roof from a bamboo napkin. A gauze-based napkin, so it is convenient to cut between the straws with a clerical knife, and the straw itself is cut well with scissors.

Unnecessary threads from the gauze base are singeed with matches. We glue straws with small gaps - we get 8 parts for each half of the roof. We put the parts under pressure to dry.

We paint the thatched roof with red-burgundy paint, dry it and cover it with 2-3 layers of acrylic varnish.

stain on water based tinting the inside of the house, reverse side roof and bottom of the stand. Lacquer after drying. Sanding with sandpaper No. 600. Remove dust wet wipe and varnish again.

We glue the stand, and attach the butterfly to the roof. On all red-burgundy faces (stand, windows, roof) you can additionally walk with a semi-dry brush with gold paint. Putting on a couple finishing layers varnish and dry well.

By the way.
The color of the stain "migrates" under the next layer of varnish, so that the entire jar of varnish does not stain, pour a little into another container.

The color intensifies after varnishing.

- The blank of the tea house is glued together with PVA building glue. Perfect option- Before drying, fix the structure with clamps. But if there are no such tools, use masking tape or rubber bands for money.

A stencil can be used to create three-dimensional elements. In this case, you need to apply a structural paste or just putty through it, smooth and carefully remove the template, and dry the volumetric pattern well.

Each layer of varnish must be dried well, and preferably in a natural way, since the varnish may crack when using a hair dryer. If drying with a hair dryer is inevitable, keep it at a distance of about 25-30 cm from work.

Almost all women simply adore various things “to please the eye” in their kitchen. The box for storing tea bags "Tea House" is exactly the "thing" that any hostess will be happy about.
To make a tea house in technology, we need the following materials:

wooden blank "Tea House";
napkin;
artistic acrylic primer;
acrylic paints for creativity (blue, yellow, green ( green foliage, brown);
bitumen (or burnt umber);
PVA stationery glue (or acrylic varnish);
paraffin candle;
facet varnish;
acrylic varnish for the final coating of the product;
brushes, foam pads, masking tape, sandpaper, stationery file, TEA stencil.

The first step in decorating wooden blank is the sanding of all side surfaces with sandpaper - bringing to a smooth state. We remove all small chips and flaws so that our workpiece is as smooth as possible. Cover after sanding external surfaces acrylic art primer.

If you are not going to decorate internal surfaces they may not be primed. After the primer has dried, you can go over with fine sandpaper again to even out the thickness of the coating if the primer was applied unevenly. To give the effect of "time", the place of future "scuffs" we paint with brown acrylic paint, which in the future will show through the main color and create the very effect of antiquity.

After the brown paint has completely dried, we rub some places with ordinary wax candle, excess and large crumbs must be removed with a sponge or soft cloth.

We cover our house with paint of the main blue color.

If it shows through brown paint, can be covered with a second layer of blue paint. After complete drying, in places that we rubbed with a candle, we carefully go over with sandpaper - we create scuffs.

The element of the napkin pattern that we will glue is quite large. In order to stick it without wrinkles, we will use the so-called technique. "pasting by file method".

On an ordinary stationery file, lay out the napkin with the front side (do not forget to remove the lower white layers of the napkin). Pour water evenly into the center of the napkin.

Distributing water over the entire surface, we level our napkin with a brush or fingers, expelling all the bubbles. Drain excess water. We attach the file with a napkin to the side surface of the house, smooth it out, gently pressing the pattern, and slowly remove the file from the edge of the napkin - voila, and not a single crease! Without waiting for drying, glue on top with decoupage varnish or PVA glue (diluted 1: 1 with water).

While our house is drying, we will decorate the roof. Primed and painted brown, we mark the roof into strips by gluing masking tape. From above, evenly, with a not very thick layer, we apply a one-component facet varnish, which, when dried, will give us beautiful small cracks and imitate “traces of time”.

Without waiting for the varnish to dry, remove the masking tape. With the help of a stencil, we will put the inscription “Tea” on the front surface. So that the stencil does not move, we attach it with masking tape and with the help of a sponge, with “bumping” movements, drive the paint (burnt umber) into the stencil.

Today's decoupage lessons with photo and video examples are dedicated to different options tea house decorations interesting ways and motives.

Having made the decoupage of a tea house with your own hands, you will receive an original decorative item that will take its rightful place in your kitchen and decorate it with itself. festive table, giving the tea party a special charm.

The first master class introduces you beautiful option for decoupage of a tea house. It will take you up to three days to create it with your own hands, but as a result you will receive a unique product that will delight you and those around you with its beauty for a long time.

In order to make a tea house, you need to prepare the following kit necessary materials and fixtures. So get ready:

The master class begins with preparation wooden surface to the primer. To do this, take sandpaper and go over all the wooden planes with it, carefully removing all uneven places. After that, it is necessary to prime the surfaces, except for the walls that are inside the house. For a primer, you can use a wide flat brush and apply a couple of layers, each of which dries. Please note that the primer is applied in one direction. If you do not have a brush available, use a foam rubber sponge or roller.

After letting the primer dry, go over it with sandpaper so that the tea house ends up smooth and even. Treat this process carefully, because with careful surface treatment, the selected motif will be located in a beautiful and even layer over the product.

At the next stage, the master class demonstrates gluing the selected drawing using an ordinary stationery file. Follow the step by step photos to see this process. So, you need to take decoupage glue and apply it on a primed plane. Next, take your chosen image and attach it. A file is superimposed over the motive. Now, using a spatula, you need to walk along the surface of the tea house, starting from the central part. In this way, the formed bubbles are driven out during the gluing of the pattern, and the motif itself is securely fixed.

Similarly, you will need to fix all the remaining images on each side with your own hands.

After that, the design of the inside of the tea house begins. Prepare a wet brush and go over the inside of the tea bag house. Moisten all the walls and the bottom in this way. Wet wooden base you need to go through sandpaper with a large grain. So, the staining process will go deeper. Next, a solution is prepared from water and ocher-colored acrylic paint. This mixture is applied in one small layer. An undiluted layer of umber-colored acrylic is applied along the lower protruding part and thickness of the product.

We pass to the roof of the tea house. It needs to be painted over with a thick layer. Brown with a wide and flat brush in the direction of the fibers in several layers. Make sure that you do not have unnecessary gaps on the plane on which the primer was applied.

After letting the workpiece dry, take a wide bristle brush. It must be dry, soak it in an ocher-colored paint, get rid of its excess with a napkin and, with a slight pressure, walk over the surface in the same direction in which the painting took place.

These actions are carried out along the entire plane of the roof of the tea house in the upper and lower parts. In this case, small stripes of ocher color are formed. As a result, the roof will become more attractive.

To give the tea house with decoupage even more elegance, it can be decorated. To do this, take interesting pattern, applied to the adhesive base and bronze patina. Next, fix desired element on the roof on an adhesive base. After that, a patina is applied to the sponge and driven into the stencil with a slight movement.

Now, using the same sponge, apply patina along the edges of the roof. Next, the roof of the tea house is covered with several layers of acrylic-based varnish. Each of the words is pre-dried. Then, an acrylic-based varnish is applied to the dried surface to finishing work.

Also, the selected images on the stencil can be applied to different corners of the product, after which, using a sponge and a bronze-colored patina, go through the corners, the borders of the cutouts and the window.

In the protruding lower part, with a light pressure of a sponge with a patina, a relief is given to the cut, as in the photo.

On the inner and outer sides, it is necessary to apply a couple of layers of acrylic-based varnish, each layer is dried before application. After all stages of drying, we fix the work with a finishing varnish.

Be sure to take this master class into service and a delightful decorative item in the form of a unique tea house will appear in your interior.

Tea house decor lesson using the Ambiente method

The next tutorial will show you interesting technology, with which another tea house will be decorated.

Prepare for work:

As usual, a master class on decoupage of objects begins with priming the workpiece.

After that, take a rice card and tear it out with your own hands. necessary elements with which the tea house will be decorated. Be sure to leave a gap of one and a half centimeters along the edges.

This master class for decoupage of a tea house uses thematic images architectural elements plotted on a rice map. These parts are glued on the surface of the product. The edges remain unglued. Let's see how this process looks in the photo.

Next, take a palette knife and use it to apply relief paste under all the borders that were not glued. These edges are glued after giving them the desired shape. Thus, interesting convex details are obtained, as in the photo.

On the walls of the house with the help of paste and a toothpick, you can make an imitation of bricks.

The roof of the tea house is decorated with a stencil with tiles.

At the next stage of the master class, the colors are mixed. Choose paints of similar colors with your chosen image printed on a rice card.

Paint over the house, its walls and bricks. Also, you can additionally paint on interesting details. In this master class, this is a vine of grapes and decorative flashlight. Further, at the base of the house, the masonry is marked. After that, paint these elements and paint cracks on the plaster.

The tile is painted over with the color "English red".

The inside of the tea house can be left untouched. At the final stage, it will be necessary to darken the roof with umber color, add light highlights to some details in the form of cobblestones and green elements. Prepared gel with a 3D effect is required for glazing the window and flashlight. It remains only to fix the whole product with a matte spray varnish.

The resulting tea house will not go unnoticed. This elegant product will organically fit into the interior and give your home a cozy touch. Explore the fascinating creativity of decoupage and unique items will fill your home.

If you are interested in this topic on decoupage of tea houses, we advise you to watch instructional video tutorials with step by step master classes for a variety of decoration of such products with their own hands.

Video: Decorate the tea house

Categories

Popular