Stick pvc edge at home. Edge for countertops with glue - how to glue? So, what is needed for gluing

Chipboard - the most suitable material to produce reliable and high quality inexpensive furniture. In order to hide the not very aesthetically looking internal structure of the product, edging is performed from the side of the end - the installation of special decorative panels melamine, PVC or other available species synthetic plastics.

Why else edge furniture

In addition to the most obvious goal - to provide an elegant appearance, furniture edging performs several other equally important tasks:

Where to hem

Furniture manufacturers often edging only the visible parts of the end surfaces. From the point of view of economy, this looks quite understandable, but taking into account the above facts, this approach can result in certain problems - the protective edge must be present in all places where there is an open internal chipboard structure.

If you purchased furniture with unprotected edges, it is quite possible to do their edging yourself at home. To do this, you do not need to have any special equipment - the edge can be glued with an ordinary iron.

Do not be too lazy to spend a few minutes on this operation - you will reliably protect yourself and your furniture and significantly extend its service life. Next, we will analyze in detail how to glue edging tape with your own hands.

Edge materials

The edging of open surfaces of furniture can be performed using different decorative elements, differing in the quality of the material, appearance and, accordingly, cost.

How to glue the edge with an iron

Edging in production is done with a tape with a clean base. The adhesive composition is applied to it during installation at a high temperature, which ensures the formation of a thin, even layer. In order to stick the edge, several rollers are used, tightly pressing it to the base of the chipboard. Then special cutters cut the tape to the size of the part, remove the remnants of glue and base material and grind the junction until a smooth and beautiful surface is obtained.

You can also glue the edge at home. To do this, you need to use a tape with an already applied adhesive composition. Further, the process largely repeats industrial edging, since it is performed similarly:

You can learn more about the process of gluing edges on chipboard in the video below:

Stick the U-profile on chipboard end somewhat easier. We have discussed this method before. Such an edge is much stronger than melamine, bends quite easily and reliably protects against damage.

The presence of microgaps between the edge of the U-profile and the front surface of the chipboard does not allow gluing it in the kitchen or in the bathroom, therefore, edging with this material is mainly used for office furniture.

Edging chipboard, of course, is best done in the factory. In production, you can order a tape from any materials, including plastic, PVC and other modern composite materials. Edging on the machine will ensure perfect evenness and accuracy of application decorative cladding, but requires certain costs. If the main task is to meet a predetermined small budget, applying a melamine tape with your own hands will allow you to combine acceptable quality and the lowest price.

You might be interested to know

This article, most likely, will not be of interest to professional furniture makers. But for amateurs who, for some reason, do not have access to PVC edge with glue applied, but really want to veneer their furniture with PVC, it will have to be “at the checkout”. Moreover, you can sculpt not only 2 mm, but also 0.4 mm PVC edge.

Today we will talk about the process of sticking this type of edge not on traditional hot melt adhesive, but on contact adhesive.

I use glue, but you can use the traditional moment.

We cut the edge into pieces slightly larger (about 10 mm) than the length of the part to be glued (I will glue the ends in the photo). A garden pruner is great for cutting, but you can just scratch the edge sharp object- it will break exactly at the place of the scratch.

We apply glue to the part (some glues mean applying to both glued surfaces - read the instructions).

Then we turn the part over and lay it on the edge, pressing it against a flat surface.

Now the part must be fixed until the glue dries.

To do this, you can use specialized edge clamps. I use - they are screwed onto the usual F-shaped ones.

It is better to press through a wooden block for a more even distribution of pressure.

The second option is to use special clamps. I made these with a couple pieces of plywood and studs.

After the glue dries, we release the parts from the clamps and cut the ends. This can be done either with the same secateurs or again by scratching and breaking off.

In both cases, such a cut is obtained, which sometimes has to be slightly adjusted with a fine sandpaper on a block.

Now we move on to removing overhangs from the faces.

We glue the edge on the chipboard

For 0.4 mm edges, a knife or ruler is enough (similar to melamine). For 2 mm edges, an edge router is required.

The curly () cutter, walking along the edge with a bearing, cuts off its protruding part.

The output is such a slightly rough cut that needs to be polished.

To do this, with a piece of felt we make several vigorous movements along the edge. As it warms up, it evens out the roughness.

As a result, it turns out like this smooth edge no worse than on professional equipment

Although more expensive and longer. The technique, of course, is artisanal, but it has the right to life.

Posted in: Practical part.
Tagged: chipboard end

Registration, processing, sealing of chipboard edges. Edging, edge, butt, finishing. fix, process, process, finish

How beautiful to seal the edge of chipboard? Finishing the end face of a polished plate, processing the edge of a laminated one. Chipboard edging techniques. (10+)

Finishing the end of the chipboard

Edging chipboard is necessary in the manufacture of furniture. Your attention materials for the manufacture of furniture with your own hands.

Chipboard edge structure

Particle board consists of sawdust mixed with glue and pressed. Moreover, the process of pressing and drying the glue is organized in such a way as to obtain dense surfaces and a rather rotten middle. This is done so that the chipboard springs and does not break. If the entire array of the sheet is made dense, then the sheet will prick from a very small deformation.

Usually we don't contact with internal structure chipboard sheet. It is fenced off from us with dense surfaces and a laminating coating (if the chipboard is laminated). But the butt reveals this charm to us. Our goal is to close it from the eyes of those who will admire our product.

In addition to aesthetic reasons, there are several more reasons why you need to close up the end of the chipboard, even in places that are not visible to the eye. Moisture. Chipboard is very sensitive to moisture, even a small amount absorbed from the air. Surfaces of laminated chipboard are impervious to moisture, the surface of polished chipboard is usually painted and also impervious to moisture. The edge should also not let moisture through. Mushrooms. Microorganisms and insects that decompose wood can penetrate into the slab through the end face. Harmful substances. Harmful substances contained in the glue and the sawdust themselves, from which the chipboard is made, do not penetrate through the laminated or painted surface, but enter the room through the end.

Options for edging, chipboard edge design

The options for processing the end face (edging) depend, first of all, on how the sheet itself will be finished. If the sheet is laminated, and it is planned to use its laminated surface white, that is, not to paint or cover with anything, then it is necessary to stick an edge tape on the visible edges that matches the type of laminated surface, and putty and seal the hidden edges with a construction bandage. If the sheet is laminated or sanded, and it is planned to paint it, then the sheet itself must be primed, its edges puttied, sealed with a construction bandage with a call on the plane of the sheet, putty bandage and painted.

End face of white-laminated chipboard

Visible end

When cutting such chipboard, you need to be very careful, use a sawing tool that leaves a smooth edge. The laminating coating of chipboard during cutting is very fond of crumbling and chipping. If this happened, then it will not be possible to correct the situation. I do not know how to beautifully repair such a chip. You will either have to put up with it, or saw off a new workpiece. Next, I recommend filling the edge. Many people glue the edge tape directly onto the sawn edge, but I tried to do this and gave up on it. The tape doesn't adhere well to the surface. I putty the edge with acrylic universal putty. After drying, the skin is medium-grained. I do this very carefully so as not to chip the laminate with chipboard. Then I stick the tape on the leveled surface.

I will dwell on the types of tapes - edges. Usually it is paper (in the generalized sense of the word ‘paper’) tape and plastic. paper tape Sold with hot melt already applied. It is glued with an iron. I will not dwell on this process in detail, there are enough materials on the network on this topic. You need to pay attention to the quality of the tape and glue. If subsequently the tape lags behind, then it can be glued with ordinary glue, this will not be noticeable. The plastic tape is glued on. The adhesive may already be applied to plastic tape and covered with a protective paper strip. This is a bad case. This glue sticks very badly. Do not buy plastic edge with glue already applied.

What glue to use? It is better to use the glue recommended by the edge manufacturer. However, note, it is worth making sure that there is a solvent for this glue, which allows you to remove excess glue and not damage plastic border and covering the chipboard sheet itself. Then you will be comfortable.

How to glue the edge on chipboard and PVC

According to the instructions for the glue, you will glue the edge, and remove the glue that has come out with a swab moistened with the indicated solvent. Difficulties can arise if the adhesive dissolves only with solvents that dissolve plastic. Excess glue cannot be removed with such a solvent, such glue is not suitable for us.

Making an invisible end

We spat him. Skin with medium grit. Carefully so as not to chip, as in the previous case. In principle, this can be stopped. However better with glue PVA glue a strip of construction bandage to the putty end. He (bandage) will prevent splitting and rash of putty. Usually the bandage is slightly wider than the edge. Glue the bandage so that the edge is in the middle of it. When the glue dries, with a sharp knife, carefully, so as not to damage the laminated chipboard, remove the excess bandage.

Chipboard edge for painting

In this case, the cut can be carried out without much concern, since chips and defects can easily be corrected with putty. If we are working with laminated chipboard, but still we want to paint it, then we apply primer to the entire product. Suitable soil GF-021 or Otex from Tikkurila. If polished chipboard is used, then priming is not necessary, although it is desirable. We putty the butt. I use acrylic putty with fine filler. Skinning. We should get a smooth rectangular edge. Sometimes this requires several iterations of sanding - putty. When the edge suits us, it must be fixed, otherwise it will chip or crack. Putty - the material is not very durable and reliable. We glue the edge with a construction bandage 4-5 cm wider than the end. We use PVA glue. We bend the bandage so that it sticks to the end of the chipboard and goes to the upper and lower planes. See drawing. After the glue dries, we putty a construction bandage of finely dispersed acrylic putty. Usually one putty is used for all these works. We especially pay attention to the strip where the bandage ends and the chipboard itself begins. Here it is necessary to putty especially carefully so that after sanding and painting the transition is absolutely not noticeable. We dry the putty, we skin it with a fine sandpaper, we paint it.

Despite the monstrous appearance on the diagram on an enlarged scale, in reality, the presence of a bandage and putty on the end of the chipboard, if everything is done correctly, is completely invisible.

Unfortunately, errors occur periodically in articles, they are corrected, articles are supplemented, developed, new ones are being prepared. Subscribe to the news to stay informed.

If something is not clear, be sure to ask!
Ask a Question. Article discussion.

More articles

Do-it-yourself arc welding. Electric welding. Tutorial. Weld seam….
How to learn welding work on one's own….

How to make a reliable heating burner with used oil? Scheme…
We will make a reliable heating burner for testing on our own. Homemade o…

We glue firmly, firmly, correctly. We choose, we select the good, the best, ...
We will learn how to choose the right glue and glue. best glue appropriate and correct...

Homemade ladder. With my own hands. Prefabricated, collapsible, sk…
How to make a reliable folding ladder yourself ....

Close the joint of the bath + walls, tiles, tiles. Sticking, sticking, sticking...
How to reliably and permanently close the junction of the bathtub and the wall? If the wall is made of panels, slabs ...

How to paint furniture with varnish. Table, wardrobe, shelves...
There is old lacquered (polished) furniture seriously scratched, varnished…

Reasons for the extinction of the flame, weak or too strong burning of the stove ....
Overview of kitchen malfunctions gas stove. Weak or too strong combustion, ...

Welding, electric welding, apparatus, Welder. Transformer, straight...
How to choose a welding machine….

PVC furniture edge

Furniture edge PVC - a narrow strip of polyvinyl chloride, which is used for pasting the ends of chipboard. It not only protects the chipboard from damage, but is also a decorative element.

Melamine edging is also widely used in furniture production. But since it is made from paper impregnated brine, has a number of disadvantages. Among them are small thickness, fragility and susceptibility to mechanical damage. That is why many manufacturers of furniture and interior items prefer PVC tape.

PVC edge has the following advantages:

• high level of strength;
• reliable protection against chips, moisture, which allows you to increase the service life of products;
• high resistance to chemical compounds, ultraviolet radiation, ignition;
• relatively low cost.

The PVC edge is a narrow tape consisting of polyvinyl chloride. Edge tape - elegant addition to furniture designs from chipboard. It protects products from physical, chemical and biological damage, while at the same time giving elegance to furniture, whether it is a countertop, cabinet or any other product. It is enough to paste over the ends of the furniture so that it acquires a finished look. Kromochnaya pvc tape able to work wonders even with ordinary furniture, endowing it with notes of sophistication and sophistication. There is a huge variety of colors, shades, decor and textures, so you can apply this decorative element to any furniture. In addition, the edging material will add furniture performance characteristics, protecting furniture from moisture and reducing the evaporation of resins.

Furniture edge is an easy-to-use and very practical decorative element that facilitates the operation of furniture made of laminated chipboard.

The high-quality edge tape gives to furniture products durability, reliability and durability. The tape is easy to wash because it is moisture resistant. The facing PVC edge is additionally coated acrylic resin so that it is not affected in any way.

In the production of furniture and components in industrial scale apply several kinds of tapes, including ABS, edging tape on glue base and PVC. When it comes to exclusive designer furniture or premium class furniture, original edging materials are used, including aluminum edge, high gloss, 3D edge, etc.

One of the best edging tapes is considered to be PVC products made in China. This edging material is distinguished by its special aesthetics and functionality, as well as a long service life.

Edge PVC China produced in accordance with latest achievements and according to all sanitary and hygienic standards. Furniture edge China is considered the best option for furniture made of chipboard and decorating an office or home.

Our company offers a large assortment PVC edges of different textures and colors. Based on your choice, we will offer you an adhesive that will most securely attach the edging material to the furniture. Of course, the question of the accuracy of furniture design will directly depend on the quality of the equipment and the qualifications of the staff. If you want to choose a unique stone surface or classic type wood texture, we will help you choose required option edge tape.

Pasting with a plastic edge of the ends of chipboard.

You will have to specify the texture, decor and color of the material, in accordance with your taste preferences. With the help of edging tape you will literally transform the furniture in your home. Products, as well as the technology of its production, meet the highest standards of quality, safety and environmental friendliness.

We offer you a wide range of PVC edging at an attractive cost.

Having glued the end of the chipboard with a melamine edge, do not doubt that the treated surface will look worse than pasting the edge on a low-quality machine - if you glue the edge correctly, in accordance with the algorithm, the result is brilliant.

What is the edge attached to?

• For parts in contact with the floor.
• To elements that will be subjected to mechanical stress in the future.
• To internal parts, for example, parts drawers chest of drawers or bedside tables, laminated boards.

What do you need for edging

• Iron.
• A cutter knife or a clerical knife, a necessary thing, can be used both when assembling furniture and assembling various elements, such as a mosquito net.
• A piece of felt or a damp piece of cloth - a rag.
• Sandpaper, and even better - a bar coated with sandpaper, it will be more convenient to work with it.
• Parts holder or vise.
• Actually the edge itself.

How is the preparation for pasting the edge

To ensure that the end result of your work looks flawless and looks quite aesthetically pleasing when edge gluing, you should use a good iron, it is desirable that Teflon be taken as the basis for the surface. Make sure that the ironing surface of the iron is clean - if there is dirt, they must be removed. If you have picked up this tool, you can start pasting for the example of wardrobe shelves.

To make the work most convenient, you should not use ordinary knives, a cutter is ideal. If you do not have such a knife, then you need to find an old knife blade and construct a cutter from it yourself.

You can make a bar yourself - you need to take even an ordinary piece of chipboard and paste over it with sandpaper on one side.

A melamine edge with an already prepared layer of glue on it is for sale, but if you are “lucky” to get an edge without an adhesive coating, you must apply glue to it yourself.

The holder can also be easily constructed independently from the remnants of chipboard, for this you need to take two small pieces of material and fill them at a small distance from each other perpendicular to the base.

The process of pasting the edges is carried out in stages

• After unwinding the bay, attach it to the end of the part, leaving a little edge for trimming.

  How to glue PVC edge on chipboard at home

  In the standard, the edge width is 2.1 cm, and chipboard, as a rule, has a width of 1.6-1.8 cm, so there will also be room for trimming and rubbing the edges. In order not to do extra work and not cut the edge lengthwise from two edges, it is better to align it on one side, and subsequently cut off the excess only on the other side.

• Having attached the edge to the facade, start heating it and ironing it. Particular attention should be paid to the edges of the ends - there it is necessary to iron most carefully.
• Details of small length are ironed entirely and immediately, and longer segments should be heated and ironed in parts - in sections of 40 centimeters. The butt is cooled with felt or a damp cloth.
• Based on the quality of the tape used, the heating temperature of the iron is selected and regulated. If everything is set correctly, then the iron glides directly over the surface, does not cling to anything and does not scratch the edge. If the heating is correct, then the glue under the edge will spread evenly. And if you overdo it too much and overheat the edge, then bubbles will go and the edge will have to be removed and thrown away.
• If you nevertheless spoiled some area, then in order to remove the damaged material, you need to heat it up again and remove it with a knife. After cleaning the surface, you can start pasting again.
• If the edge is of high quality, then it will stick only after it has completely cooled. Having found that the edge has completely cooled down, you can start trimming the excess. You can cut it correctly by bending the edge, rubbing it with a bar until a white chamfer is visible. Seeing the substrate, you can already cut off unnecessary material.
• After trimming, all edges are carefully and carefully rubbed with sandpaper. At this stage, the pasting of the melamine edge is completed. And you can safely proceed to the installation of handles.

The edge is used to protect the end edges of parts made of MDF, chipboard, PVC from abrasion, moisture and impact. This finish has a decorative function, as well as giving strength to the edges and corners of furniture and protecting people from the harmful effects of a substance such as formaldehyde, which is used in the production of compressed wood boards.

If the border is damaged or peeled off, it is necessary to urgent repair. And in this case, the primary task is the selection of material and adhesive for PVC edges, melamine paper or other materials.

Edge Varieties

From the variety of edges you have to choose the most suitable.

Melamine

Made in the form self-adhesive tape from decorative paper impregnated with melamine resins. Typically used for interior decoration furniture. This is a budget option edges for chipboard, not characterized by high quality. It has a short service life, is susceptible to moisture and often disappears by itself over time.

Undoubted positive property melamine edge is the ease of gluing it, you can do it yourself at home using a regular iron. The second advantage is the absence of a side, a curb protruding above the edged surface, which sometimes annoys when it gets under the hands when working with the keyboard, and also prevents sweeping away small debris, for example, crumbs from dining table in the office.

Represents a flexible tape with the bent edges which form a side. This edging is made of PVC (polyvinyl chloride). The types of edging differ in width and profile: in cross section, the edge resembles either the letter “t” (T-shaped) or the letter “p” (P-shaped).

The latter is easier to attach, but less reliable, masters do not recommend using it on surfaces that are often subjected to friction: on the seats of stools or benches, on the front edge computer desk, which is constantly in contact with the forearms.

PVC edging increases the durability, wear resistance of furniture parts, reliably protects edges and corners from damage.

The border is similar to the previous type of edge tape, but more environmentally friendly. Made from chlorine-free plastic. Has found successful application in furniture production, thanks to heat resistance and impact resistance.

How to glue melamine edging

Update if you wish old furniture and at the same time save money, use a melamine edge with glue. Sticking it, for example, on the countertop is easy:

1. Cut off a piece of tape with a margin of about two centimeters.
2. Attach the adhesive side to the countertop and press with a hot iron or heat with a building hair dryer.
3. Hold to melt the glue words.
4. Move the iron along the edge gradually, preferably no more than 0.5 cm at a time.
5. Immediately after warming up and removing the iron, press the edge strip with a dry cloth and hold to fix it.

Advice! Also, an iron or hair dryer will help you remove the old edge tape. Just heat and remove with a knife or thin spatula.

Fixing PVC and ABS piping

Plastic edging tapes, theoretically, can be simply fixed on the edge of the furniture, but this is extremely unreliable. Additional fixation with glue is preferred.

For fastening T-profile you will have to lay a recess along the entire processed edge. The easiest way to do this milling machine. If you have the skill, it will be replaced by a drill with a circular nozzle. However, in general, the profile is intended for professionals.

To fix the edges of PVC or ABS at home, PVC glue is used, as well as the universal compounds "Moment" and "88-Lux", it is desirable that they be marked "for PVC" or "for ABS".

Professionals use hot melt adhesives, which are part of a range of thermoplastics. When heated, they acquire high elasticity, and when cooled, they instantly turn into solid state. The high fluidity and drying strength of the adhesives are due to the ethylene-vinyl acetate polymer contained in them. The main disadvantage of hot melt adhesives, of course, is the need for appropriate equipment for the job.

When working with any border, try to calculate the pasting sequence so as to avoid joints. Bend around the corners with a profile - it is desirable that they be rounded. If the corners are normal, a thick (PVC or ABS) profile will not go around them, and the melamine edge will most likely break. In this case, joints will have to be made at the corners, which at the end must be processed with sandpaper so that they are smooth. If you run your hand along the edge of the part, then the roughness should not be felt.

Advice! You can get rid of excess edging tape with a very sharp knife, and the ends are cut first. Be careful not to accidentally damage the corners of the furniture. The direction of the knife should be inside the part.

If the factory edge is damaged or partially fallen off, remove it and replace with a new one. A little effort, and the table is like new!

Chipboard is the most suitable material for the production of reliable and high-quality inexpensive furniture. In order to hide the not very aesthetically looking internal structure of the product, edging is performed from the end - the installation of special decorative panels made of melamine, PVC or other available types of synthetic plastics.

Why else edge furniture

In addition to the most obvious goal - to provide an elegant appearance, furniture edging performs several other equally important tasks:

Where to hem

Furniture manufacturers often edging only the visible parts of the end surfaces. From the point of view of economy, this looks quite understandable, but taking into account the above facts, this approach can result in certain problems - the protective edge must be present in all places where there is an open internal chipboard structure.

If you purchased furniture with unprotected edges, it is quite possible to do their edging yourself at home. To do this, you do not need to have any special equipment - the edge can be glued with an ordinary iron.

Do not be too lazy to spend a few minutes on this operation - you will reliably protect yourself and your furniture and significantly extend its service life. Next, we will analyze in detail how to properly glue the edge tape with your own hands.

Edge materials

The edging of open surfaces of furniture can be performed using various decorative elements that differ in material quality, appearance and, accordingly, cost.

How to glue the edge with an iron

Edging in production is done with a tape with a clean base. The adhesive composition is applied to it during installation at a high temperature, which ensures the formation of a thin, even layer. In order to stick the edge, several rollers are used, tightly pressing it to the base of the chipboard. Then special cutters cut the tape to the size of the part, remove the remnants of glue and base material and grind the junction until a smooth and beautiful surface is obtained.

You can also glue the edge at home. To do this, you need to use a tape with an already applied adhesive composition. Further, the process largely repeats industrial edging, since it is performed similarly:

You can learn more about the process of gluing edges on chipboard in the video below:

Sticking a U-shaped profile on the end of the chipboard is somewhat easier. We have discussed this method before. Such an edge is much stronger than melamine, bends quite easily and reliably protects against damage.

The presence of microgaps between the edge of the U-profile and the front surface of the chipboard does not allow gluing it in the kitchen or in the bathroom, therefore, edging with this material is mainly used for office furniture.

Edging chipboard, of course, is best done in the factory. In production, you can order a tape from any materials, including plastic, PVC and other modern composite materials. Edging on the machine will ensure perfect evenness and accuracy of applying decorative cladding, but it requires certain costs. If the main task is to meet a predetermined small budget, applying a melamine tape with your own hands will allow you to combine acceptable quality and the lowest price.

The edge in furniture production is necessary to protect the end edges of the product from chips, cracks and other damage, and it also protects against moisture and formaldehyde vapor.

You will learn about what edges are, as well as how to glue them and how to glue an edge with an iron and a hairdryer, from this article.

Types of edges - why are they needed

1. The most common type is melamine edge with glue on paper basis . It is applied to finishing of internal sites of furniture. Affordable, inexpensive, but not the best quality option. Does not tolerate moisture, wears out quickly. Easy to stick at home with a simple iron.
2. T-shaped flexible profile - is a T-shaped bar, it is inserted into a slot in the side of the chipboard or MDF. It is convenient to replace the damaged element in the future without disassembling the furniture. Installation requires a milling machine.
3. PVC edging - reliably protects the ends of furniture from damage, is wear-resistant, resistant to moisture. Gluing PVC edging will require an edger, so using this type of edge at home is difficult.
4. ABS plastic is an eco-friendly, chlorine-free option. Valued for resistance to high temperatures and physical damage.

All options can be divided into two subspecies - edges without glue and with glue.

The average cost of a profile per linear meter:

• PVC 0.4 mm thick - about 25 rubles,
• PVC 2 mm thick - about 40 rubles,
• Melamine material for chipboard - about 25 rubles.

In our country, products from Rehau are actively used, which offers big choice color solutions, as well as different width tapes from 15 to 45 mm.

To simplify the work, you can use various specialized furniture programs that will calculate how much material is needed to glue the edges.

PVC edge - how to glue in stages at home

For work you will need:

• iron or building hair dryer,
• and of course buy a PVC edge with glue
• hard roller,
• newspaper or paper sheet

The material is heated to make the adhesive sticky. Heating is performed with an iron in the "Synthetics" mode.

• The profile is applied to the end in such a way that it overlaps the end of the section.
• Next, the iron again performs heating through the newspaper. Since the glue dissolves quickly, the process is quite active, and it is convenient to move the iron along the PVC edge.
• The edge itself must be carefully pressed and ironed until it sticks along the entire length.

1. Bonding with a building hair dryer. Instead of an iron, you can use a building hair dryer. The PVC edge is heated from the adhesive side and when the composition becomes sticky, the material is applied to the end desired area, pinch and gently smooth.
2. Gluing with glue "Moment". This method is suitable if there is no adhesive layer on the edge. The quality of the butt is checked manually, sawdust, rubbish, dust are removed until the surface is clean. Then glue is applied to both the material and the end and wait until it sets. After that, apply and press. Using a roller, the area is rolled so that the glue grabs faster.

VIDEO

How to remove excess material

If it was not possible to carefully glue the edge the first time, the procedure will have to be repeated. To do this, glue is again applied to the area and the profile is clamped with a roller or manually.

Since usually the width of the PVC edges is taken with a margin, you need to carefully remove the excess along the edges. To do this, use a regular clerical knife or file. It is taken with both hands and pressed on the protruding fragment. As a result, the excess parts are broken off and an edge remains that matches the width of the site.

Shutdown

After everything is glued, it remains to process the bumps with sandpaper.

How to glue an edge on chipboard - a description

Melamine edge is best option for use at home when it is necessary to restore old furniture with minimal cost. If the furniture is expensive, it is better to turn to professionals who use other more expensive and high-quality material.

Consider, how to glue the edge on a chipboard tabletop at home.

GREAT VIDEO RELATED TO THE TOPIC

To work, you will need the following materials:

• skin,
• sharply sharpened knife-jamb,
• wallpaper roller,
• melamine edge,
• building hair dryer or iron.

Action algorithm:

1. select the operating mode of the iron so that it does not get too hot and does not burn the chipboard and at the same time ensures proper melting of the glue,
2. process the edges of the chipboard for gluing with sandpaper, eliminate irregularities,
3. measure the profile
4. heat it with an iron and press it firmly against the area with a roller (if there is no adhesive layer, you will need to apply glue to the edge yourself, for example, Moment glue),
5. cut off the hanging edges of the edge with a knife.

It is necessary to cut at an angle along the edge, slightly wringing the material. Then it remains to sand the edges so that there are no burrs and irregularities.

If the cut of the edge and the chipboard itself are slightly different, the stain will help correct the difference.

In case the item has complex shape, and the edge of the surface is characterized by complex relief, the first time it is not always possible to glue the material evenly. In such a situation, it is worth contacting professionals so as not to spoil the product.

What glue to choose for the edge

Professionals furniture production actively use hot melt adhesives for edging. They are convenient in the event that production will be put on stream, and it is required as high quality results, and fast speed.

Hot melt adhesives are thermoplastics, which means that when heated they become very elastic and when cooled they harden quickly. The polymer of ethylene with vinyl acetate, which is part of the adhesive, is responsible for these properties. The disadvantage of using is the need to use special equipment, namely the appropriate machines or hand guns for applying glue to parts and heating it.

1. AT living conditions often use PVC glue, which sticks well paper materials to various surfaces. Homogeneous without lumps light color the mass adheres well to surfaces, but is afraid of moisture. Does not require application additional equipment, therefore it is convenient for operation by non-professional craftsmen.
2. fit universal adhesives"Moment" and "88-Lux", which will reliably stick the material to the surface of chipboard and PVC. After 3-4 hours the product can be used. Adhesives are inexpensive, safe and available.
3. From professional furniture glue for the edge, it is worth noting products from Kleiberit. The company offers hot melt adhesives for cladding, for gluing the material using the soft-forming method (in case the surface is embossed), as well as for cladding.

Often, due to furniture design errors or other reasons, it is necessary to glue the edge on the laminated chipboard. Sticking a traditional plastic edge at home is almost impossible, especially without special equipment. The melamine edge saves, since there are enough colors for it. Let's see how a melamine edge sticker is made and what it is all about.

Without going into details of what the melamine edge itself is made of, we can say that it is a tape on which glue is applied. At the same time, the glue is thermal, so just sticking it will not work. At the same time, thanks to the thermal adhesive on the laminated chipboard, it holds well.

Fig.1.

Before proceeding to the description of the process of gluing the melamine edge, a few words about essential tool and preparation of the chipboard end. To apply a melamine edge, you will need construction hair dryer, a knife and a pair of construction gloves.

Fig.2.

The end of the chipboard plate must be clean and even., without sawdust and flaking parts. Otherwise, the edge will stick not to the chipboard, but to them and it will not stick well. The best end face is obtained after milling or sawing on the machine. Next, the photo will show the end Bad quality, there just wasn’t anything better at hand.

Fig.3.

The melamine edge sticker is started by cutting a strip of the desired length from the main roll or slightly longer than required. In this case, the end that will be glued first must be trimmed. You can do this with regular scissors.

Next, apply the edge to the end of the chipboard. It should be noted that the melamine edge is produced in a width of 20 mm, i.e. it is wider than chipboard. Therefore, at this stage it is important to align it along one edge, as in the photo.

Fig.4.

Please note, on the other side of the chipboard, the edge protrudes. In the future, it must be cut.

Fig.5.

Next comes the hair dryer. A temperature of 250 degrees is sufficient for gluing a melamine edge. The edge is heated with a hair dryer, thereby melting the glue. characteristic feature, indicating that the adhesive has melted, is the moment when the edge loses its curved shape, after being in the roll, and becomes straight. Then she just presses against the butt chipboard hands. This must be done with gloves, because. hot edge.

There are several features that should be mentioned.

Edge bonding should be done in a warm room., this will ensure a slower curing of the glue. Accordingly, there will be more time to correct the situation.

It is necessary to warm up the melamine edge not along the entire length, but 20-30 cm each. It is easier to work this way, and the glue does not have time to harden until the edge is pressed against the chipboard end. So, on average, an end face 60 cm long is glued in 3 approaches. The first - the beginning of the edge is glued, the second - the middle part of the edge, the third - the end of the edge.

Do not forget that the air temperature from the hair dryer is about 250 degrees, so you need to work carefully and Do not point the hair dryer at your hands or other objects.

Fig.6.

There are many options on the Internet on how to glue an edge. For example, heat it with an iron. In my opinion, this is not advisable. Sometimes, when overheated, the glue flows out from under the edge, and most likely it can ruin the iron, and it costs more than a hair dryer. It is also suggested to cool the edge different ways. This is also not advisable, because. at a room temperature of 25 degrees, the edge cools down until the glue hardens in a few seconds, and in my opinion it is not advisable to come up with additional operations.

The last step is trimming the melamine edging.

Fig.7.

In this case, cut off the usual kitchen knife, there was simply nothing else at hand. The result is not the best. Good result gives sharp knife with a thick blade, like a shoe knife. The knife should be placed at an angle to the edge of the order of 30-45 degrees from the bottom side. Gives the best result special device for trimming the melamine edge, but I personally did not manage to purchase it.

In conclusion, I will say one more thing. interesting feature. As you can see in the photo, the edge cut has White color that against the background of cherry color does not look very good. You can fix this with a wood stain on water based. You just need to moisten a rag in the stain and wipe the cut with it, remove the excess. For example, for chipboard colors cherry is well suited for mahogany wood stain.