How to clean the pipe in the bathroom from hair. The solution to the age-old problem: how to easily clear the blockage in the bathroom and sink. Lemon juice in the fight against blockage

During the operation of plumbing, each owner is faced with the need to clear the blockage. Drains in the bath are more likely to clog. If the water slowly flows into the sewer pipe or stands still, do not rush to look for a plumber. You can deal with this problem on your own, using improvised means, household chemicals and proven pipe cleaning methods.

What causes constipation

In most cases, a tight plug is formed due to small debris, threads from clothes, hair, pet hair, and even soap bars getting into the drain pipe.

First time encountering problems drain system bathtubs, remember that there are three categories of blockages:

Mechanical - caused by the accumulation of debris deposits.
Operational - formed due to the lack of regular prevention.
Technogenic - associated with improper installation of the system, wear and tear of equipment and all kinds of gusts, accidents, leaks, etc.

If there is no blockage, and the outflow of water is weak, check the pipes. Perhaps the reason lies in the insufficient slope of the outlet pipe or in the small size of its cross section. Increasing the slope of the drain pipe will get rid of the problem. Lower the socket of the sewer riser or raise the bathtub.

If a blockage needs to be cleared, use comprehensive methods to clear all pipes, including the sewer riser.

Methods for mechanical cleaning of drains or pipes

Mechanical blockages are removed manually (with a plunger and a plumbing cable), as well as using improvised means and household chemicals.

Reliable assistant - plunger

Plunger - a design consisting of a handle and a rubber tip in the form of a suction cup.

Before using the plunger, draw water into the bath (it should cover the rubber tip of the device).
Install the rubber plunger tip over the drain hole.
Quickly and vigorously press the tool handle, pushing the plug in the outlet pipe.

For the cable blockage is not an obstacle

If using a plunger did not achieve the desired result, use a special cable - a flexible steel product with a ribbed metal spiral or a brush at the end. The cable will quickly penetrate into hard-to-reach parts of the sewer pipe, removing clogs and dirt that have stuck to the walls.

To clean the sewer pipe of the bath, gently insert the cable into drainer.
Combining translational and rotational movements, direct it towards the alleged blockage.
To achieve the desired effect, move the cable back and forth, remove it from the pipe and rinse thoroughly in clean water.
Flush the system clean water.

When cleaning, remember that plastic structures fragile and can be damaged due to powerful mechanical impact.

Plumbing cable will get rid of blockages formed in hard-to-reach places

Video: removing blockage with a cable

If you have a vacuum cleaner

You can clear a clogged drain with a vacuum cleaner equipped with a reverse blow function.

Remove rubber nozzle from the plunger handle, and install it on the vacuum cleaner pipe, securely fastening it with electrical tape.
Remove the dust bag from the vacuum cleaner.
Connect the hose with pipe and plunger to the blow hole.
Install the plunger tip over the drain and turn on the vacuum cleaner.

The principle of operation of the device is the same as when using a cable

Differs from manual method only by the fact that the cable does not rotate by hand, but with the help of an engine in a special device.

Hydrodynamic method

Based on the use of a pressurized water jet, the water temperature can reach up to +120 °C (superheated steam).

Hot water, let into the pipes under high pressure, will wash out any "plug"

Hydrodynamic and mechanical methods require the use of special equipment, therefore, as a rule, only professional teams of plumbers use it.

How to clean a siphon

A lot of dirt that prevents the free outflow of water accumulates in the siphon, as well as in the area where the outlet pipe is connected to the common sewer riser. This can cause an unpleasant odor in the bathroom.

To clean this device, carefully disassemble it using the following procedure.

Take a rag that absorbs liquid. Spread it under the siphon, as water will pour onto the floor during dismantling.
Place a basin under the siphon.
Slowly unscrew the lock nut of the device.
Dismantle the siphon flask.
Rinse the device with clean water, removing plaque and debris accumulated on the walls.
Install the siphon in its original place so that the drain pipe does not rest on its flask. Otherwise, the water seal may be broken, and the bathroom will appear bad smell sewerage.
Turn on the water to fill the water seal. Check if the connections are tight.

It is easy to disassemble and assemble the siphon

How to get rid of drain odor

A persistent and unpleasant sewer smell in the bathroom indicates clogged pipes and bacterial growth. The reason for their appearance lies in the violation of the integrity O-rings, cracks in pipes and siphon, its clogging, evaporation of liquid from the water seal. To destroy such "aromas", it is necessary to eliminate the described defects, clean the siphon or blockage in the pipes.

You can get rid of the unpleasant smell in the bathroom with the help of chemicals and folk methods.

Method one:

Pour 150 g of mustard powder into the drain hole.
Pour hot water into it.

Method two:

Pour the chlorine solution into the drain hole of the bath, protecting your hands with gloves in advance.
After 10 minutes, flush the system with clean water.

How to clean an old faucet (faucet)

The reason for a sharp decrease in water pressure may be a cork consisting of rust and scale particles, or a clogged aerator.

Before cleaning such a blockage, remember the safety measures:

Be sure to turn off the water using the valves located at the entrance of the pipes to the house or apartment.
Open the faucets, checking for water ingress.
When tightening the faucet elements, do not use too much force so as not to strip the threads.
Use caution when operating a faucet to avoid scalding hot water.

Aerator cleaning

Remove it using a wrench.
Rinse the nozzles with high water pressure or clean the mesh with a needle.
Reinstall the aerator.

Cleaning a single lever mixer

Wanting to increase the pressure of water in a tap equipped with single lever mixer, do the following:

Remove the handle of the device, fixed with a screw (it is hidden under a plastic plug, red and of blue color) on the front side.
Carefully remove the plug.
Loosen the screw and remove the handle.
Remove the cover of the device housing, under which the mechanism is hidden.
Using a wrench, unscrew the clamping nut.

Determine what type of mechanism is used in the crane.

If the valve is equipped with a disc cartridge, pull the stem with a light and careful movement and remove cylindrical mechanism. Such a cartridge cannot be repaired and requires a complete replacement.

When disassembling the ball mechanism, it is important not to lose small parts and springs. The body of the device itself should be thoroughly rinsed. If you find serious damage on the parts and with the ball hanging freely in the socket, it is better to replace the mechanism. After cleaning, assemble the mixer in reverse order, carefully tightening the fixing screw.

Prevention of blockages in the bath

You can prevent the appearance of mechanical blockages through preventive measures:

Taking advantage simple methods and means, you can independently cope with the cleaning of simple blockages sewer system. Do not forget the algorithm of actions: find out what material the pipes are made of, select suitable ways and means of eliminating blockage, do not forget about safety and prevention. Let the water in the shower and bath bring you only pleasure in the future.

In any even the cleanest bathroom, a blockage can form. Of course, tidy owners face this problem much less often, but it is impossible to exclude the appearance of a blockage. In order to be fully prepared and not to get confused in case of a problem, you need to have several important tools on the farm and carefully study how to clear a blockage in the bathroom.

Causes of mud plugs

Sooner or later, lumps of hair, wool, particles of rags and other substances collect in the pipes, which form a mud plug and prevent the passage waste water. Also, one of the causes of blockage can be a fatty coating, which contributes to the sticking of household contaminants. In order to understand what to do when the pipe is already clogged, it is important to determine the nature and extent of the blockage.

Clogged drainpipe

If it happened in apartment building, then first you need to find out whether it is a local blockage (in the apartment sewer wiring) or a common house (in sewer riser). When the blockage is local, you can handle it on your own, but with a common house, you can’t do without a specialist.

It is very simple to determine: it is enough to open the water at two points (bathroom and kitchen) and observe: the water does not go away only at one of the points, which means that the blockage is local; stands at both points - the pipe riser is clogged and you can safely call a plumber. And you can deal with local blockage on your own. You just need to follow a number of rules and listen to the advice of experienced people.

Blockage removal mechanically

There are several methods for cleaning pipes from blockage:

thermal - using hot water, boiling water;
chemical - with the help of corrosive drugs;
mechanical - with the help of a plumbing cable, opening the siphon cup;
pressure cleaning - using a plunger.

Attention! Do not use the thermal method on pipes that may not withstand elevated temperatures.

Sometimes filling out an application to call the master and waiting for him can take several hours. A blockage in the sewer makes it impossible to use both the water supply and the sanitary unit as a whole.

Vantuz is always at hand

A good hostess has everything at hand in her arsenal necessary funds for any situation. Plunger is one of the most important household items. Without his help, you can not do with blockages in the bathroom or in the sink in the kitchen. Cleaning a blockage in the bathroom with a plunger is a little more difficult than in the sink. When removing such a blockage, it is necessary to close the overflow hole with a plug or a second plunger in order to create a vacuum at the cleaning point.

Removing clogs with a plunger

How to clean the pipe in the bathroom with a plunger:

Lubricate the bottom of the rubber cup of the plunger with petroleum jelly.
Align the plunger with the hole in the tub.
Close the bathtub overflow hole with a plug or a second plunger.
Pour in enough water to cover ¼ of the plunger cup.
Make several progressive movements.
Remove blockage.

Please note that the tub and sinks are connected and the pushes created by the plunger reach them as well. Be sure to cover the drain holes to prevent the contents from splashing out.

Plunger allows you to clear the blockage in the pipes without the help of specialists

Tip: Sometimes the problem is solved by unscrewing and cleaning the siphon cup.

If the blockage was not cleared the first time, repeat the procedure again. Please note that only those blockages that are located close to the drain can be removed with a plunger, if the pipe is clogged behind the siphon, then you should choose another method.

Rope - an effective way

If the plunger turns out to be useless, then the problem is much more serious. We'll have to resort to heavier artillery - a plumbing cable. The length of the plumbing cable is usually no more than 3.5 m. In order to clear the blockage in the pipe, it is necessary to insert it into the drain hole.

Slowly rotating the handle located at one end of the cable, it is necessary to insert the device until it rests on the blockage with the other end. With a sharp rotational movement, you need to pick up the blockage in the pipe and perform a back and forth movement, thus clearing the clogged pipe.

Plumbing cable with nozzles for clearing blockages in pipes

On the opposite side of the handle, the cable has the shape of a drill, thanks to which mud plug loosens and its small fractions immediately pass further down the sewer, and the main part of the blockage clings to the cable and is pulled out. When removing the cable from the drain hole, you should immediately wipe it from dirt so as not to stain all the contents of the pipe.

Attention! Take precautions when working with sewer blockages. Work in thick rubber gloves, wear goggles and a mask so as not to pick up an infection.

Do not work with the cable alone. It is difficult for one person to cope with both the direction of the cable and its rotation in the pipe. In addition, the cable is made of elastic steel, and can spring and injure you.

Chemistry will cope with any blockage

What to do if the pipe that is clogged cannot be cleaned either by the plunger or the cable, and even cleaning the siphon does not give the expected results? In this case, you have to resort to chemicals. With the help of chemistry, you can clean any blockage without applying the slightest effort.

Chemical preparations for cleaning blockages require careful observance of the instructions for use

When choosing a pipe cleaner, you should consider all active ingredients the chosen drug. Some of them are so aggressive that their use is possible only in cast iron pipes. And some can be used exclusively for plastic piping.

Very important!!! When working with any chemical preparation, maximum care and protective equipment is required.

To achieve the desired result, it is necessary to pour the amount indicated on the label into the drain hole and wait until it does its job. Then open the warm water and clean the sewer pipe with water from the blockage and the flooded product.

Observe safety precautions when working with chemicals. Avoid contact with skin or mucous membranes. You should also be careful not to get such products on chrome surfaces, otherwise it can not only clean the pipe, but also clean the mixer from the chrome coating.

Chemicals easily deal with almost any blockage in pipes

Also chemicals they are also used for prophylactic purposes, small doses of the substance, diluted with water, are poured into the drain hole and wait a few minutes for the drug to take effect. Then washed with running warm water. This procedure is carried out at least 1 time per month.

Tip: be afraid of harm environment- use folk remedies to clear a blockage in the bathroom. They are not as effective, but they are safe.

Folk remedies

What people just didn’t come up with to clear blockages in pipes with the help of improvised means. fell asleep citric acid, sucked up the blockage from the pipe with a vacuum cleaner (this method is highly not recommended - it leads to the purchase of a new vacuum cleaner), but not all of these manipulations were effective enough. In practice, it turned out that it is best to eliminate blockages in the bathroom with soda and vinegar.

If you don't want to use mechanical means for cleaning pipes - folk methods are suitable for you

Cleaning with soda. ½ pack of soda is poured into the drain hole, after 5-10 minutes it is poured hot water.
Vinegar cleaning. 4 tbsp is poured into the drain hole. l. soda and pour a glass of vinegar. The hole is closed. In 10 minutes. washed with a liter of boiling water, and then with a large stream of hot water.

There are a lot of all kinds of methods invented by the common people, each housewife is trying to invent her own unique way to clear a clogged pipe in the bathroom, but often these are all in vain gestures. For the most part, folk remedies are suitable for kitchen sinks, because they cope better with fatty blockages, but cleaning with vinegar is also suitable for the bathroom.

Blockage Prevention

To avoid having to clean blockages - do not allow them to appear

In old worn-out pipelines, the likelihood of a mud plug increases due to crevices and roughness on the inner surface of the pipe. The most the best prevention blockages is a timely replacement sewer wiring and risers. Also, in order to avoid blockages, it is necessary to install a removable grate on the drain hole, which will trap unwanted contaminants and small things that accidentally fall into the drain.

It is always better to remove pollution from the outside than to get it out of the pipe, while pouring the contents of the sewer pipe into your bathroom and flooding the neighbors.

Buy a plunger and plumbing cable so that they are at hand at the right time

Do not hide the plunger and cable far away; they must be in an accessible place. In a panic, in the event of an accident and the eruption of the contents of a sewer pipe, there is not always time to remember where you threw the plunger you bought several years ago. You need to act quickly.

How to fix a clog in the bathroom with the help of available tools: video

Cleaning pipes from blockages: photo

The situation when the water in the sink “does not want” to go through the pipes is familiar to many, so it is important to know how to clean the blockage in the bathroom. There are several options for this: chemicals or assistants. They have different efficiency and safety of use. The key in the fight against blockages is systematic, because the slow outflow of water does not just happen, you do not need to wait until the pipes are completely clogged.

Plastic device for pulling blockages from pipes called "snake"

Folk ways for cleaning pipes are also very effective

Why does clogging occur?

Before you start the fight, you need to know the enemy in person, and therefore, figure out what are the causes of blockages. The first, and perhaps most important, is human life. It is not always possible to control what and in what volumes gets into the sink, and hence into the pipes. The most difficult in terms of clogging are:

The hair, the longer, the more reliably the pipe is clogged.
Animal fur.
Pieces of rags (rags).
Paper, napkins.
Items that should not be in the pipes.

Blockages are different, and vary in the degree of passage of water. If it does not leave at all, then this is a complete blockage, this occurs if a cork of loose debris has formed in the pipes, the same hair, wool, paper. If the water leaves, but more slowly than usual, then this is an incomplete blockage. And this is even worse, because over time, an unpleasant smell will also be added to the difficulties with the outflow of water, because what is stuck is in a “favorable” environment with high humidity will start to rot and give off a smell.

incorrect operation. Do not wash pets in the bathroom, carpets;
incorrect installation of the piping system. If there is insufficient slope or sagging pipes, blockages will be common.

Note! It is possible to deal with blockages, but it is easier to prevent their formation.

Blockage Prevention

Preventive measures boil down to preventing foreign pipe debris from entering the sink. Preventing blockages is easier if it becomes a habit. Key measures:

Install a special mesh with small holes in the drain hole. She will not hold everything, but a lot of garbage remains on her.
Carry out preventive cleaning from time to time in the following ways.
Regularly - once a week, pour boiling water over the pipes. The volume of water is within 2-3 liters. It will wash away the deposit soap scum on the walls.
When replacing pipes, check correct angle tilt.

How to clear a blockage in the bathroom: plunger

Using a plunger is the most common way to clean a blockage in the bathroom at home.

Note! Using a plunger is an excellent prevention of the formation of soap scum on the pipes in the bathroom.

It would seem that the most traditional way, but for its implementation you need an understanding of the process. If the blockage has formed in the sink, then cleaning is quite simple:

install a plunger on the drain hole;
make 10 sharp movements up and down.

Often this vacuum is sufficient for cleaning.

The bathroom is another matter. All due to the fact that there is another system for draining water. When water overflows, air enters the opening, and in such conditions it is impossible to create a vacuum. You need to act like this:

Close the hole for pouring water tightly with a cork.
Lubricate the plunger with Vaseline and press it against the drain.
Make 10 reciprocating movements. The sharper the better.

Note! When cleaning a blockage in the bathroom, you need to close the hole for pouring water well, just don’t plug it with a rag - this will not give the desired effect. The best decision it is to use another plunger, but this requires an assistant.

If this does not help to “break through” the blockage, you should use another method. To do this, draw water into the bathroom, and it must be hot. Level - half the height of the rubber cup of the plunger. The latter is immersed in water at an angle. At the last pitching down, the plunger must be pulled out of the water. Repeat the procedure several times if necessary.

Plumbing cable

The previous method is only suitable if the blockage is minor, it cannot cope with a serious blockage. Option - plumbing cable. It is suitable if:

Blockage deep in the pipe.
The “cork” that closes the outflow of water is strongly compressed.

The essence of the method is to get rid of the blockage mechanically, pull it out or push it deeper into a wider pipe. The length of the standard cable is 3 meters, and this is quite enough to extract deep blockages.

The technique of using the cable is simple, but it must be clearly maintained. Subsequence:

the cable is inserted into the drain hole;
one person pushes, the other rotates the cable. This contributes to the destruction of the blockage and prevents the cable from breaking at pipe bends;

after the blockage has been passed, you need to make a couple of jerks back and forth. After opening the hot water, you will wash away the dirt that has formed on the pipe;
Now you can carefully pull out the cable.

Such a cleaning tool can be purchased at any hardware store.

Note! It cannot be used for plastic and chrome pipes, the rope design may damage their inner surface.

Special funds

Ready-made chemicals that can get rid of blockages, the choice is huge, as well as the expansion of prices. Before you clean the blockage in the pipe in the bathroom with one of them, you need to familiarize yourself with the recommendations for using such products. If the blockage is running, then it will not be possible to do without chemical means, you will have to use the mechanical ones presented above to help.

Advice! When choosing, preference should be given to where it is indicated that it dissolves wool and hair.

Important Tips:

Powder and liquid products do not differ in effectiveness.
When buying, check with the seller whether the product is suitable for the type of pipes that are in your home.
Liquid products should be poured directly into the drain hole, powders after falling asleep, pour hot water (1 cup).
After the time specified in the instructions, spill the pipes with hot water in order to rinse the pipes well and remove debris.
When using these products, it is important not to use the bath for a while. It is best to clean at night.

Note! When using any chemical agent, it is important to strictly follow the instructions. After all, even the highest quality of them cause damage to the pipes.

Specific funds

In the store in the thematic section, you can get confused, but there are a number of products that are especially popular with consumers. Among them:

"Mole" is a long-known remedy used by our mothers and grandmothers. But it cannot be used for plastic pipes;

"Mr. Muscle" is suitable for all pipes. The active substance penetrates into all nooks and crannies of the sewer system. In addition to eliminating various types of blockages, it removes bacteria, thereby eliminating an unpleasant odor;

"Tiret" - eliminates blockages quickly. Has no smell of ammonia;

"Pothan" - dissolves all types of blockages, and quickly.

When working with any chemicals, use rubber gloves, oilcloth apron and goggles.

After using the product, if there is a siphon in the bathroom and kitchen, it must be thoroughly cleaned.

Folk methods

If you are looking for methods on how to clean a blockage in the bathroom sink or in the bathroom itself and do not want to use chemicals, but mechanical methods for some reason they cannot be used, folk methods will come to the rescue.

There are many dubious methods that will not only not be able to get rid of the blockage in the pipe, but will also lead to additional expenses. Among them:

Use of a vacuum cleaner. handset household appliance bring it to the drain hole and turn it on at full power. The results are deplorable, and the most minimal of them is the purchase of a new vacuum cleaner.
Citric acid is simply not effective.

In practice, the effectiveness of soda has been confirmed, and it can be combined with salt or vinegar.

soda+vinegar

To implement this method, the following ingredients are needed:

soda;
vinegar (it is best to use white distilled);
boiling water;
rag or washcloth.

Cleaning sequence:

Pour half a package of soda into the drain hole. It is important that the soda is dry.
Pour vinegar in a volume - 0.5 tbsp. It's good if you warm it up a bit. Cover the opening immediately with a cloth. This will keep the volcano that forms from the baking soda and vinegar inside the pipe.
Leave everything like this for 30 minutes. During this time, the debris that blocked the outflow of water will dissolve.
Then boil the kettle.
As soon as the allotted time is up, pour boiling water into the hole.

If it was not possible to immediately completely get rid of the blockage, then the manipulations should be repeated.

soda+salt

Another option, how to clean a blockage in the bathroom with soda, is even easier to implement. You need to take 0.5 cups of salt and soda, hot water. Cleaning sequence:

Pour soda and salt into the drain hole.
Add 1.5-2 liters of boiling water there.
Leave for 8 hours. It is important that this drain period is not used.

Pipe cleaning is a simple task and there are many options that are suitable for different type pipes. When using them, you must follow the instructions and safety measures. But still the most simple option is prevention, and it is quite simple. You just need to get used to the fact that the pipes should be flushed regularly.

uninterrupted and long work sewerage depends on the correct and timely cleaning of pipes. If their clogging has already happened, then decisive action should be taken. The first sign of clogged drains is the slow flow of water into the hole.

Due to clogging, dirty drains can get into the apartment, which causes a lot of trouble, and the appearance of an unpleasant smell is no exception. To prevent similar situation, it is important to clean the pipes in a timely manner and eliminate sewer blockages as soon as possible.

Cleaning the sewer with a sewer cable

In some cases, improvised methods are ineffective, so before you dissolve the hair in the sewer, you need to decide on the choice of products based on chemical substances. In fact, due to the large variety to choose effective remedy hard enough for pipes. Certain features must be taken into account.

Causes of sewer clogging

First you need to determine what a blockage of sewer pipes is and what methods exist to deal with such a problem. So on internal surfaces pipelines, organic and inorganic residues can be deposited. The same surface is often susceptible to mechanical damage, for example, it can be scratched. Due to the unevenness of the inner walls, debris lingers and accumulates over time.

This phenomenon can lead to the fact that the diameter of the pipes will steadily decrease. Thus, the lumen of the pipe can become 2 cm narrower, which necessarily causes failures in the working process of the entire sewer system. To prevent this from happening, it is necessary to periodically clean the sewer pipes.

As a rule, the nature of the blockage can be different, namely:

mechanical - debris accumulates due to the ingress of a foreign object into the pipeline. These items are most often toilet paper, paper waste, feminine pads and other household waste;
technological - mainly horizontal pipe sections are clogged, as well as pipes with a minimum slope. To prevent such a water problem, it is important to properly install the sewer system in compliance with the mandatory technical requirements.

dissolving hair with special chemicals

Since the causes of clogged sewers can be different, there are several effective solutions with which you can get rid of the problem:

blockage can be eliminated mechanically using a plunger or a cable;
using chemicals;
the place of the alleged blockage can be treated thermally;
in difficult situations it is recommended to flush the sewer pipes with a hydrodynamic unit.

using a cable and a brush-like nozzle to clean the sewer and eliminate blockages

Chemical treatment products

If there is a need to quickly clean the sewers, spending a minimum of effort and money, it is recommended to use funds based on chemical compounds. By their composition, such products can be alkaline or acidic, they can be purchased:

in the form of a gel;
liquids;
granulated powder.

The main active element is the surfactants contained in the product. It is they who interact with fat and lime deposits.

Withstanding a certain amount of time after backfilling or pouring a chemical agent into the drain, you need to pour warm water to wash off the softened cork. If the work is done correctly, then if the blockage is small, the system should recover.

Products based on chemical compounds are ineffective if the sewer pipes are completely clogged, as evidenced by stagnant water in the drain hole. In such situations, the chemistry will simply come out, which can damage the plumbing fixture.

do-it-yourself sewer cleaning

Gels

A distinctive feature of such products is viscosity. The exposure time to pollution in sewer pipes is longer. When water is poured into the drain hole, chemical reaction does not slow down. This is due to the fact that substances penetrate deep into the sediments.

Gels are considered effective, while they are not as dangerous compared to granular formulations. The benefits include:

impossibility of damage plastic pipe and relatively long time impact;
when the funds hit decorative surfaces their destruction does not occur;
gels are relatively inexpensive.

Liquid preparations

To eliminate sewer blockages, experts recommend using liquid chemicals that are highly effective. The holding time must comply with the instructions in the instructions, since there is a risk of damage to the plastic pipeline with rubber seals.

The advantages of the drug form include:

ease of use;
low cost.

Products in the form of granules

Of the variety of drugs, the most effective is the remedy in the form of granules. Pour exactly the amount indicated on the package into the drain hole and pour the glass warm water. After half an hour, flush the pipes with water.

The main advantages include:

no risk of destruction of plastic pipes;
prevention of reaction with metal pipes;
dissolution of hair, which is the most common cause blockage;
effective removal of lime deposits.

In addition to the advantages, there are also disadvantages, which are:

skin reaction hazards;
chemical activity;
relatively high cost.

Before dissolving hair in the sewer using granular products, gloves must be worn and protective mask while the room should be well ventilated.

Most Popular Chemical Based Products

Wondering how to flush the sewer, many decide to use a tool such as the Mole. It has been known for a long time, because it has a good effect. In addition, it helps to remove plugs from threads, hair, fat and other organic compounds. Mole can be used for various pipes. Also, this product is chosen for preventive measures.

checking the drain near the drain hole

If it happened serious blockage, then you will need to apply other products, which include Tiret. It does not pose a particular danger to sewer pipes. On sale you can find Tiret for the prevention of blockages and a gel remedy, which has a stronger effect.

Flushing sewer pipes can also be done with the help of Mister Muscle. It is considered a gentle product, as it gently affects blockages. The most effective form is foam, which can be used to dissolve deposits of organic origin. In addition, unpleasant odors are removed and bacteria are destroyed.

A potent, yet expensive remedy is Bagi Potkhan. With it, you can easily dissolve hair, grease, paper and a layer of lime. The drug can be used for different kind pipes. Do not allow product to come into contact with the surface. plumbing fixture as they may be damaged.

In the process of using Potkhan, you need to be extremely careful, since the reaction begins immediately after the water enters.

Good alternative budget option for cleaning pipes is Fluop, which is sold in granules. To activate the process, the powder can be poured hot or cold water. Certainly, best effect will be if you purchase a powder intended for pouring hot water. You need to act strictly according to the instructions, avoiding getting the product on your hands and eyes.

Using chemicals, you can not only solve the problem of sewer clogging, but also disinfect the entire system, as bacteria are destroyed and unpleasant odors are eliminated.

If water began to slowly drain in the sink or shower, then there is reason to believe that the pipeline is clogged. To fix the problem, you need to know how to clean the blockage in the bathroom with soda, vinegar and other improvised means.

To fix a problem, you must first determine the cause of its occurrence. If you frequently bathe your pets in the bathroom or clean fluffy textiles, they are the cause of clogged drains. In this case, a lump of thread, hair, grease, soap residues formed in the bend of the pipe, which not only interfere with the normal flow of water, but are also sources of bacteria and an unpleasant odor.

Photo: blockage in the bathroom sewer pipe

If you have metal pipes, then they may have become clogged due to mineral build-up. This happens mainly in houses of old construction, because earlier only cast-iron or steel pipes. If you are sure that the problem is in the "overgrowth" of the inner diameter, then you cannot do without the intervention of a specialist.

How to eliminate

The easiest way that can be implemented at home is to fill the pipe hole with soda and add vinegar. You will need:

Half a pack of regular baking soda;
Half a glass of vinegar;
Hot water - as much as possible.

First, you need to pour soda into the drain hole, then wait 10-15 minutes, and pour vinegar into it. Be careful, a chemical reaction will begin, due to which vapors will appear. To protect yourself from their effects - after pouring vinegar, you can not be directly above the drain hole. After half an hour of exposure, pour a few liters of boiling water into the pipe and wait. Most often, simple blockages dissolve very quickly.

If the problem is serious and the hairball cannot dissolve the soda, then you can use special cleaning products. Any store sells "Mole". This is a powder designed for cleaning pipelines. It consists of serious chemical reagents, therefore, it is able to dissolve almost any blockages (except for mineral ones). You just need to pour it into the problem drain and rinse it off with hot water after half an hour.

Video: Blockage in the bathroom. How to eliminate?

Eliminates odor very effectively and at the same time cleans the Domestos water passage. This tool dissolves not only fatty blockages, but also hair with dirt. For exposure, pour two caps of detergent into the bathroom pipe and leave for the maximum possible period of time. Best of all - at night. In the morning, rinse the communication with hot water. This method cannot be used to clean a clogged pipe if it is made of plastic - active substances can dissolve the molecules of the material and over time the pipe will leak.

How to get a blockage with a cable

Sometimes you can clean the lump that caused the blockage in the bathroom by hand.

Scheme: How the cable works

You need to remove the cover that protects from foreign objects downpipe;
Then insert a special plumbing cable into the hole. Unlike the wire that is used for the toilet, the cable for the washbasin or bathroom pipe has a smaller diameter, respectively. It's more flexible;
When introducing, it is necessary to gradually twist the wire so that it can pass along the bends of the pipeline to the site of blockage;
It remains to push the garbage to main pipe. According to SNiP, the drain leading from the sink has a smaller diameter than the main sewage pipe. Therefore, if debris gets into a large communication, it will simply pass without problems and free the pipe.

At home, craftsmen also use ropes with a hook on a horse. They are designed not to push through the blockage, but to get it out. This technique is very effective for blockages close to the drain surface.

You need to take the wire and bend it at the end;
Enter the cable into the pipeline, scroll it gently;
Gradually push it inward, as soon as you feel resistance - turn the wire and hook the blockage with the tip.

If you need to quickly clean a small blockage in the bathroom, formed from hair, you can not do without a plunger. This is universal tool, which perfectly copes with any type of mechanical pollution.

Fill a sink, bathtub or shower tray with some water;
Place the plunger over the water drain hole, then press it so that it sucks air from the pipeline;
After that, make several movements that contribute to the movement of the blockage inside the pipeline. It is very important, when you finish the work, to abruptly release the plunger so that water under a certain pressure enters the pipeline.

After that, you can use improvised means that will be removed from inside pipe remains of grease and debris.

How to clean a siphon

Sometimes the problem is not a clogged pipe, but a dirty siphon. In this case, it is required to clean this part of the sewer directly. Before you remove it, you need to place a container under the knee to collect water.

Using necessary tools, remove the nut and gasket that hold the siphon to the elbow. When removed, water will pour out of it, which has lingered in the pipe, so it is better to work with latex gloves. Then remove the debris from the knee and rinse it detergents and hot water, be sure to wipe the inside of the pipe with a brush - this will remove hair and other contaminants from it. Reinstall the siphon.

After installing the knee, it is advisable to spill it with a solution of vinegar and hot water - then the unpleasant smell from the pipeline will be eliminated. Sometimes home craftsmen use bleach, but it destroys sewer materials.

Categories

Popular