Loggia in 1 glass is it worth insulating. How can I insulate a balcony with cold glazing. Varieties of glazing sliding structures

Hide

Insulation of cold glazing is sometimes used, although usually this exercise takes a lot of time and effort, but does not give the desired result, since in most cases it is carried out incorrectly. Before work, you should learn how to competently insulate the balcony, making it a comfortable room.

What glazing is considered cold?

Quite often, when buying an apartment, the owner is faced with what she already has. Often the builder does not apply expensive materials and installs cold glazing, without warming the balcony at the same time. In this case, it may be relevant to replace cold glazing with warm , which will greatly improve final result, as it will help eliminate heat loss that occurs precisely through the window frames.

However, you can improve and. Most often, it is aluminum frames. Aluminum itself has a high thermal conductivity, so the room cools down quickly. Plastic double-glazed windows can also be cold. Most often this is a problem of single-chamber structures. This type of glazing can protect against precipitation, wind, dust, but does not resist frost well. Therefore, the insulation of the cold glazing of a loggia or balcony plays quite important role to create a comfortable atmosphere in the house.

How to insulate a balcony with cold glazing?

How is glass replacement going?

Any work is carried out in several stages. This procedure is performed as follows:

• Calculation of the mass that the parapet can withstand. Do not use too heavy glazing, as this can lead to the collapse of the structure.
• It is enough to simply remove cold windows: for this you will need to cut off the mounting foam, pull out the glass, and disconnect other fasteners, if any. After that, the frame can be pulled out.
• New windows are being installed. It is recommended to use plastic with double glazing. They usually do not weigh very much, while retaining heat well.
• If you had panoramic cold glazing, then you can install plastic windows from the floor, or build a parapet from lightweight materials, such as a gas block.
• You can choose any windows according to the way of opening, it only depends on how much free space there is on your balcony.
• If it is impossible to install windows with a thick double-glazed window, you can put energy-saving glasses on a thin one, they will help to keep warm, while not increasing the weight of the structure.

Replacing a building is technically easier and does not require special permits, so it is recommended to change the glazing to the same as it was in shape, with the only difference being that it will be used warm design. After the installation is done, you need to install glazing beads on the glass, adjust the fittings.

Insulation of cold glazing and its subsequent replacement with warm one is a waste of effort and money, since when dismantling old structures and installing new ones, the tightness will be broken. The finish can also be damaged, new cracks will appear in the seams. If you plan to make a warm balcony, it is recommended to start work with the replacement of glazing, and then carry out work on the insulation of structures. They are made in exactly the same way as with the insulation of cold glazing.

Cold glazing is used mainly to protect the balcony from precipitation and drafts, but even with proper insulation, it is not able to protect against frost. If you plan to make the balcony really warm and significantly raise the temperature inside it, it is recommended to immediately replace the cold frames with warm ones.

A warm loggia or a warm balcony is not a luxury at all in conditions when cold weather in our latitudes it lasts for six months, from mid-autumn to mid-spring. Modern man strives to get the most out of its living space. Here it is worth paying attention to valuable square meters, which are often either not used at all, or littered with old rubbish - a balcony or loggia. At right approach it may well turn out to slightly expand your territory due to the space of the loggia.

The Russian climate is notable for the fact that for a significant part of the year the weather does not indulge in warmth. Ordinary balcony glazing reliably protects against noise, wind, dust and rain, but the temperature on such a balcony during the cold season will be the same as outside. warm balcony allows you to comfortably use it in winter, and in some cases even combine a balcony with a room.

If you are planning to make the balcony a continuation of the living area of ​​the apartment, then you cannot do without a whole range of measures to insulate the balcony. How to insulate a balcony, where to start and what to insulate? Let's go in order...

Warm balcony glazing designs

The first step is to choose the right design for glazing. To do this, let's go through the assortment of the warm glazing market:

PVC glazing

In fact, this is the glazing of the balcony with PVC windows, the same as those used for glazing the windows of the premises. Sufficiently airtight, lightweight, budget design of warm glazing for a balcony. PVC systems There are many profiles: KBE, REHAU, VEKA, TROCAL - some of this is a mass market, and some is luxury.

Basically, our customers choose PVC glazing as a system for a warm balcony or loggia.

Why warm glazing PVC windows are so popular? Yes, because it is really the best price / performance ratio.

Sliding system Slidors

it sliding system glazing: PVC profile + double-glazed windows. Slidors has a feature that can be regarded as both an advantage and a disadvantage - it is a sliding opening mechanism. Due to this, Slidors is less hermetic when compared to PVC windows, but more hermetic than the cold construction of aluminum glazing.

Slidors are an "intermediate option" between warm and cold glazing, both in terms of functionality and budget. room temperature on a balcony with such glazing it will be difficult to achieve. But for shallow balconies, the Slidors sliding system is what you need: no additional space is required to open the doors.

Wooden windows

Wooden windows are one of the best options, especially for large balconies. The design is massive and heavy, but solid. On a budget, good - a luxury product. In terms of ecology, they are in the first place.

Thermal insulation in general depends more on the selected double-glazed window, and not on the material of the profile. Accessories must be of high quality: wooden windows heavier than PVC.

Warm wooden glazing will last a long time. However, it should be borne in mind that wood is a living material, it reacts to changes in temperature, humidity and other environmental factors.

Warm aluminum

Warm glazing system aluminum profile higher class than PVC windows. without delving into complex specifications, we note the main features of the aluminum profile: keeps warm, good noise insulation, long service life, elegant appearance. Important point: aluminum - eco-friendly, safe material. Despite its lightness, glazing made of warm aluminum profiles is quite durable and reliable. The price range is above average.

Front post-transom profile

This warm glazing system is fundamentally different from all types of windows and warm aluminum. Simply put, this is not a window that is installed in the opening, but a translucent wall, which in itself is a carrier.

This glazing is used in modern construction for glazing facades of skyscrapers. The design is relevant for floor-to-ceiling warm glazing of large balconies, irregularly shaped balconies, construction winter gardens, erection of warm translucent roofs.

The VIP Balcony company works with all the listed structures.

There are a lot of options for warm glazing of a balcony, and which one specifically better fit, depends to a large extent on the object of glazing. Our experts will always be able to suggest which glazing is right for you, and what options are possible.

Insulation of balconies and loggias

After warm glazing is installed on the balcony, we proceed to the next stage - this is the insulation of the balcony. Here, initially, you should pay attention to what exactly needs to be insulated. If you make a room out of a balcony, then everything needs to be insulated: walls, floor, ceiling. Penoplex, penofol, mineral wool are used as a heater. The tighter the insulation, the less drafts there will be. A draft is the main cause of heat leakage. So the joints of the insulating materials must be carefully sealed.

Stages of balcony insulation

Insulation of the balcony after installing PVC glazing It is important to take into account the top extensions and expanders so that the sashes open Laying polystyrene foam on the floor Sealing the seams with mounting foam Draft plywood floor 10 mm Insulation of the balcony walls The walls and parapet of the balcony are covered with insulation Wooden crate for future finishing Laying the second layer of PPS on the floor balcony Installation of a warm floor on a balcony Warm removal of glazing is much more complicated than usual Requires sealing and insulation of connection points Ceiling insulation on a balcony Balcony ceiling, PVC paneling Insulation of balcony walls, material - foam plastic

What we have: a balcony with PVC glazing. Even at the stage of glazing, it is important to take into account the upper extensions and expanders. Otherwise, the finish will rest against the double-glazed window and the sashes will not open. We insulate the floor: we lay PPS on a flat and clean surface, carefully sealing the seams mounting foam. We lay the subfloor using 10 mm plywood. We insulate the walls and ceiling with penofol. We install wooden crates for future finishing, level the surface of the walls and ceiling. We lay the second layer of PPS on the floor of the balcony. We install a warm floor and fill the screed.

Warming completed. The balcony is ready for further finishing.

Warm floor on the balcony and loggia

The warm floor on the balcony can be used as the main heating if the balcony itself small sizes. Consider several options for underfloor heating:

Classic underfloor heating

The installation of a warm floor begins with the alignment of the balcony slab. To do this, a cement screed is poured onto the clean surface of the balcony slab. On top of the screed, after it has completely dried, a layer of PPS insulation 50–30 mm is laid. The next step is to lay a reinforcing mesh in order to increase the strength of the floor, avoid cracks and spreading of the screed, and also to ensure the solidity of the slab. Then comes the second layer cement screed, which is poured over the underfloor heating cable. And only after the screed has completely dried, you can lay the tiles.

• Cons: The installation of a classic underfloor heating on a balcony is quite long and laborious process, and such a construct is very heavy for a balcony slab.
• Pros: the most economical option.

Bulk warm floor

This method of erecting a warm floor on a balcony is very similar to the previous one. The only difference is the floor leveling stage. A special bulk material is used, which is leveled, and a GVL sheet is laid on top. Fast, easy and reliable.

Step 1. We lay mineral wool under the existing metal remote frame (additional insulation of the balcony)
Step 2. The vapor barrier acts as a barrier to natural moisture and prevents it from accumulating in unwanted places.
Step 3 OSB plate used to level the floor
Step 4. Reinforcing panels are additional insulation for the balcony and reinforcing the floor as a whole. The panels are laid in 2 layers in a checkerboard pattern, and the joints are carefully sealed.
Step 5. Laying the balcony floor heating cable. Near the glazing, we choose a laying step 2 times less than on the remaining area in order to avoid freezing.
Step 6 thin layer screeds and laying tiles

Warm takeaway glazing

Very often, the customer wants to expand the space of the balcony, increase the window sill. In this case, such a technique as the removal of glazing comes to the rescue.

Removing glazing on a cold balcony is a simple task. But such a removal is completely inapplicable for a warm balcony, since with the usual (“cold”) removal of glazing, freezing of the window sill, ice and constant dampness at the junction of the glazing and the parapet are possible.

As a result of their own developments, VIP Balcony specialists have found the right technology insulation and sealing of the removal of glazing. Our insulated stem has been time-tested, and there have been no complaints from users during operation.

The conclusion is this: if you are planning not just a warm balcony, but also the removal of the glazing structure from the parapet, monitor the quality of the insulation of the connection nodes.

warm roof

Roofless balconies are a fairly common situation. Either these are balconies of the last floors, or balconies located in a checkerboard pattern.

A cold roof is done quite simply, but with a warm one you need to tinker. The roof on a warm balcony is very demanding on factors such as leaks, freezing, blowing.

Therefore, even at the design stage, it is very important to clarify how and with what the adjunctions to the glazing structure and nodal connections are insulated and sealed.

Warm balcony: foam block parapet

Insulated parapet

The foam block parapet insulates the balcony The foam block parapet serves as the basis for the construction The foam block parapet will last for centuries

Sometimes the insulation of a metal parapet is not enough to create a warm balcony. Then we resort to such a technique as the construction of a parapet of foam blocks. Such a parapet will no longer require significant insulation, its service life is “for centuries”, it will withstand any heavy structure, and if necessary, also the roof resting on it.

Such a solid warm parapet also has disadvantages:

• Weight: not every balcony slab can handle such a load. In such cases, warm French glazing will be more advantageous. The difference in the weight of the glass parapet (from PVC structures) and a parapet of foam blocks - about one and a half times.
• Installation complexity: balcony glazing will have to be carried out in several stages.

Important: It is better to order a warm parapet, as well as warm glazing and balcony decoration, in one company, it is cheaper and faster, and when installing on a turnkey basis, it is easier to plan the terms of reference.

Warm balcony glazing: photos of completed projects

Warm French glazing

Warm glazing of the balcony from floor to ceiling Warm glazing, flooring, wall and ceiling decoration Warm balcony glazing from floor to ceiling PVC profile was used for warm glazing of the balcony Finishing the ceiling and walls of the balcony in the same style Warm balcony: finishing the ceiling and walls The floor of the balcony was tinted, to muffle the yellowness of the wood Floor, walls, window unit of the balcony are in harmony in color Balcony flooring - warm natural wood Warm balcony glazing - PVC profile and double-glazed windows Inside the double-glazed windows - white false cover (sprosses) In the center of the balcony - a section with hinged glazing The sashes swing open in different directions , opening a wide opening A magnificent panoramic view opens up from the balcony Swing sashes in the center of the balcony with warm glazing Swing sashes in the center of the balcony with warm glazing The extreme glazing leaves are tilt-and-turn At the end of the balcony there is also a tilt-and-turn glazing PVC profile and double-glazed windows will keep heat well lo False binding (shprossy) in a double-glazed window Warm French glazing: PVC profile and double-glazed windows Energy-saving glass was used for warm glazing

Balcony glazing from floor to ceiling is commonly called " french glazing". Since double-glazed windows go from top to bottom, there is no need to insulate the parapet. Warm glazing was made to the entire height of the balcony with PVC plastic windows. Double-glazed windows made of energy-saving glass - with white false cover (shpros) inside. In the center of the balcony there is a section with hinged glazing, the outer doors on the sides and the ends of the balcony are double opening, tilt-and-turn. In addition, the walls, floor and ceiling of the balcony were insulated and finished, a wardrobe was installed. warm balcony with French glazing was completely turnkey.

Warm PVC balcony glazing

The floor, ceiling and parapet are insulated The parapet is trimmed with plastic eurolining Balcony insulation with PVC glazing

Balcony insulation: glazing with PVC windows, hermetically and reliably. Installed built-in wardrobe with plastic filling. Finishing of a parapet from within - plastic eurolining. There is a large dryer-liana under the ceiling.

Warm balcony in peasant style

Complete insulation of the balcony: PVC glazing The window opening of the kitchen is blocked from below with a foam block The door of the balcony block opens outwards The door of the balcony block does not take up space in the room Finishing: textured laminated PVC panels Warm glazing provides a comfortable temperature Sun blinds installed Insulation and turnkey finishing of the balcony

The peculiarity of this balcony is that the window of the balcony block is installed flush with facade wall building, thus the window sill from the side of the room is doubled, and there is no window sill on the balcony. The decoration of the balcony and the facade of the built-in wardrobe are made in uniform style, textured laminated PVC panels are used, color " peasant style". When finishing the balcony, we re-made internal glazing: the door of the balcony block opens outward, without taking up space in the room; the window opening of the kitchen from below is laid with a foam block for installing furniture, which gives the impression of a stepping. At the request of the customer, two types of sun blinds were installed: Roman (Roman) pink and roll-cassette in a flower. Colors and patterns are specially selected. An Italian dryer was installed on the wall (it unfolds like an accordion). Full insulation and waterproofing were made, the balcony was completely turnkey.

Warm PVC glazing of the loggia on Olof Palma

Loggia insulation: underfloor heating, porcelain stoneware tiles Warm PVC glazing and loggia decoration

To insulate the loggia, a warm floor was installed, metlakh ceramic granite tiles on the floor, full insulation of the walls and ceiling, 100 mm PVC clapboard trim.

Glazing warm windows PVC, glazing sashes - tilt-and-turn, open through one. This allows you to safely wash the glazing. A number of non-tearing (deaf) frames along the bottom of the glazing makes the parapet of the loggia too high. This increases the safety of small children on the loggia.

In the cold season, the tenants of the apartment face the question: how to insulate their glazed balcony to use it, just like in summer, despite the terrible cold outside the windows. The solution to this problem will be step-by-step warming all surfaces of the balcony. For a comfortable stay on it in winter time year, it is necessary to correctly consider the choice of materials for thermal insulation. The quality and order of work are no less important in the process of insulation.

Insulation of a balcony with a brick parapet

Insulating material will help to effectively insulate the balcony of their brick

The facades of new houses for the most part form a single architectural composition. Violation of its integrity by piling up additional materials for insulation is unacceptable or is associated with multiple bureaucratic delays in coordination. the best way to insulate balconies with cold glazing will be finishing insulating materials from inside the room.

A balcony or loggia often has a brick parapet. Installation aluminum windows with this design occurs directly on the top row of bricks. The insulation of such a room will be effective due to the fact that an insulating material with low thermal conductivity can be laid against the wall of the parapet.

Glass insulation

Most of the heat will escape through the glass

In the case when plastic double-glazed windows are installed, additional insulation window is not required. To isolate the leaky joint between the glass and the frame, a special polyurethane sealant is applied to the joints to prevent air from penetrating.

The greatest heat loss will occur through the glazing.

Floor insulation

Penofol can be used as insulation

An important ingredient in getting warm room is floor insulation. For better thermal insulation, you can use the following materials:

1. Penofol.
2. Electric floor insulation.
3. The beam is wooden.
4. Styrofoam or mineral wool.
5. Mounting foam.
6. Floor board.

Foil penofol is laid on the surface of the concrete floor. This material has excellent insulating properties. It will not allow condensation to accumulate in the thickness of the floor, providing oxygen access to prevent the appearance of moisture and fungus. The next step is to install an electric underfloor heating.

Underfloor heating - one of the options for insulating a balcony

The thickness of the lag sets the size of the insulation layer. The larger its layer, the better thermal insulation. When installing, it is necessary to take into account the height from the future floor to the parapet. In the standard version, it ranges from 95 to 105 cm. The safety of a person on the balcony is always in the foreground, so you need to choose the thickness of the lag, taking into account the height of the floor construction pie.

Parallel to each other in the same plane are installed wooden bars in increments of 30-40 cm. Mineral wool or polystyrene is laid between them. All gaps formed during the laying process can be sealed with mounting foam. In the winter season, a special mounting foam is used, which has the properties of hardening when low temperatures air.

It is laid on the laid logs batten for painting and varnishing. You can use draft wood with the subsequent laying of any finishing material on it.

Wall and ceiling insulation

For wall insulation, you can use the following components:

1. Penofol.
2. Wooden bars.
3. High density foam.
4. Mounting foam.

To strengthen the balcony, see the video:

Walls requiring insulation are sheathed with penofol. The crate is usually made of a 50x50 mm bar. For convenience, the step between the bars can be made consistent with the width of the filler. The foam is placed between the bars and attached to the wall with plastic "fungi". The cracks formed during installation are also sealed with mounting foam. As a sheathing, you can use eurolining or imitation timber. Plastic panels also suitable for wall cladding.

Insulation of panoramic balconies

Panoramic balconies have an excellent appearance, they have a number of advantages over balconies with partial glazing in terms of aesthetics. But the insulation of such a balcony with cold glazing will result in large financial costs. Insulation of the floor, ceiling and walls, except for the facade, can be done in the same way as in the case of parapet balconies, but the glazed wall will require a different method of insulation.

How to insulate panoramic balconies, see this video:

Frame window system cold glazing consists of an aluminum profile, which has excellent thermal conductivity.

The supply of heat to such a room at negative temperature outside air will lead to the formation of frost on the windows, and warming up will be insignificant due to serious heat losses.

As mentioned above, unauthorized changes to the facade of a residential apartment building, may cause conflict with authorities local government and with other residents of the house.

Installation of an additional glazing circuit

When installing an additional glazing circuit, the usable space will decrease slightly

Installing a second row of double-glazed windows will not cause damage general view building. The resulting air chamber will ensure heat retention on the balcony or loggia. The disadvantage of this method of insulation will be the inconvenience of washing the glass inside the chamber. usable space the room will decrease by the indent and the thickness of the inner wall, which can be a significant drawback in a limited area.

Energy saving glass film

There is a special film that is glued directly to the glass. It significantly hinders good thermal conductivity. With the help of energy-saving film, you can achieve heat savings of 20-30%. Appearance windows will not change at all when glued. It also protects against harmful solar radiation.

Watch this video on how to properly stick an energy-saving film:

Profile replacement

To insulate the structure frame, you can replace the existing aluminum profile with the same analogue, but with a special polyamide insert. This method is quite expensive, since you will have to completely replace the entire frame of the glazing wall.

Thermal insulation of the balcony, which was originally thought out by the designer as a cold room, is a rather costly and time-consuming task. It is advisable to get competent advice from specialists in the field of construction before making a decision on insulation.

Glazing and insulation of balconies and loggias will help to significantly increase the comfort in the apartment. This is not very expensive, but labor-intensive procedure, thanks to which free space outside the living space can be made more useful, use it as part of a room or a separate area where a rest room can be placed, winter Garden Store infrequently used items in a comfortable environment.

How is a balcony different from a loggia?

First of all, you need to know about the differences between a balcony and a loggia. These elements have design difference: loggia has side walls and does not go beyond the facade, and the balcony is hinged structure, outwardly resembling a basket, it has no side walls, and the plate is fixed to the facade, and not to the underlying structure.

Balcony

Glazing and insulation of balconies and loggias follows approximately the same pattern. The only difference is that it is a little easier to work with a loggia and you don’t have to think about how to organize the side walls and fix the ceiling if you are on the top floor. The rest of the work is almost identical.

Loggia

What is required for glazing a balcony?

Glazing and insulation of balconies cannot always be done without special permission. The fact is that this procedure leads to a significant change in the appearance of the facade of the building, if you live in apartment building, you will have to receive such paper. Glazing is heavy, so you have to get acquainted with technical regulations at home, find out how much weight a balcony slab can withstand. In some cases, the plate is reinforced, but this is not always technically possible, plus it requires additional costs.

It is impossible that the weight of the glazing exceeds the maximum allowable, as this will lead to the collapse of the structure, the owner of the premises is responsible for the consequences that it entails.

How is glazing carried out?

It is quite possible to glaze and insulate the balcony with your own hands. This will make the process cheaper, but some jobs may require special equipment Then it will not be possible to do without the help of professionals.

Before starting work, it is required to assess the technical condition of the structure. If the balcony slab is dilapidated, it needs to be strengthened. After that, the parapet will need to be replaced. If it is concrete, you are lucky and you don’t need to do anything, it often happens near loggias: if the parapet is made of metal rods, it is cut off and changed to . If the fence is decent and does not interfere, then it is better to leave it. It is important that the design has as little weight as possible.

After the parapet is ready, glazing is installed on it,. If it is required, internal work is carried out to insulate the walls.

Insulation with expanded polystyrene

What materials can be used?

Glazing and insulation of balconies and loggias can be carried out using various materials. To do this, you can use wooden, aluminum, plastic windows, various heaters, the most popular are PVC windows and insulation such as mineral wool and foam.

Foam insulation

After the balcony is insulated, you will need interior decoration. It is needed to isolate the insulation and give the structure decorative look. Finishing can also be done different materials, it can be of the following types:

• Drywall is moisture resistant.
• PVC sheets.
• Siding.
• Clapboard.
• Brick.

Each material has different technical and external characteristics. Types of glazing can also be different, for example, warm glazing and insulation of the loggia are most conveniently carried out using plastic double-glazed windows. They have a fairly large mass, but their thickness is optimal in order to retain heat indoors with high quality. At good insulation a balcony or loggia can become a full-fledged part of the living space. It will be possible to conduct heating there and use the structure as a small room.

Cold frameless glazing

Cold glazing will not give such an effect. It will not make any sense to insulate a balcony when using an aluminum profile, since the metal very quickly gives off heat to the atmosphere. However, this glazing option is cheaper than warm and can be used if the balcony is not used as a residential one. If you plan to simply protect the structure from rain and wind, making it comfortable for use in summer time, storing things, smoking or drying clothes, then this option will suit you well.

Glazing and insulation of the loggia with wooden euro-windows will be of no less quality than when using plastic structures, however, such frames can be even heavier, depending on the type of wood, and the structure itself will cost more. You can use a simple wooden frame, this option is good for country house or non-residential balcony. Homemade frame made of wood will not be able to retain heat well, so you should not expect such a design to be warm.

External foam insulation

How is insulation work done?

Glazing - two procedures that do not make sense separately from each other. If everything is very clear with glazing, then how to deal with insulation? First you need to choose the materials with which you will work.

Floor insulation

Advice: it will be necessary to insulate not only the walls, but also the ceiling and floor of the structure, otherwise the heat will escape through them.

To get started, you need to fill out construction foam all the cracks of the structure, waterproof it: mastic is suitable for this. After that, you can proceed to the rest of the work.

The most accessible material for insulation is lying or glass wool, but you need to work with this insulation with protective gloves. You will need to create a crate, you can make it from wooden beam 4x4 or metal profile, the resulting cells are filled with cotton, then closed vapor barrier film, sew up exterior trim such as drywall sheets.

Foam insulation

The use of polystyrene foam (styrofoam) instead of mineral wool it will also require the creation of a crate, but it is much more convenient to work with it: the foam holds its shape, it is easier to attach it, you can use special glue. The material does not allow water to pass through, therefore it does not require waterproofing the room, in addition, it does not crumble and does not cause irritation to the skin and respiratory tract.

Conclusion: glazing insulation of loggias and balconies - the procedure is quite interesting. You can do it yourself or hire specialists. Wide selection materials will help not only to qualitatively insulate the structure, but also to give it the necessary decorative look.

I want to say thank you so much company GK Expert, a very responsive manager Marina and a highly qualified specialist in his field Stas. Special thanks to him! I decided to specifically insulate the loggia and only in this company did I find the service of PPU insulation at a very reasonable price. At first, I was very surprised that different brigades came for each operation. They dismantled the old balcony, then inserted windows, then upholstered, insulated, sheathed ... They took out all the garbage from the old balcony, it became even cleaner than it was :))). And everyone did it different people. Unusual, and I did not expect that everything will turn out so cool. The people are different, but the professionalism is the same. High!

Our house is a unique phenomenon in the bad sense of the word. When it was built, they completely forgot about insulation. And as soon as the autumn rains begin, the walls are covered with divorces and stains, and mold appears in the corners. The wife insisted on glazing and repairs, fearing for the health of elderly parents. We decided to turn to the masters of GK Expert, because the neighbors on the floor above, thanks to them, turned the loggia into a real oasis. A turnkey finishing complex with insulation and wall cladding is an expensive pleasure, but the result exceeded our expectations. Now we relax on the balcony, and we store potatoes and jars of jam in the garage. Very satisfied and grateful!

Six months ago, a large balcony was glazed, we contacted the GK Expert company, the neighbors advised us. The work was done well and competently, and everything was done on time, and most importantly, very neatly, no traces were left anywhere. And their manager is pleasant, smiling and satisfied with life, he always communicated politely. And they also gave us a good discount and gave us a heater as a gift, it’s nice when they care about you like that and make more gifts! In general, both service and quality are on top, what more could you wish for?

Glazed balcony in the company GK Expert. I liked the quality work, the service is good. I doubted, so I was looking for someone to order from for a long time. We chose GK Expert, because our friends advised us this company, and they gave us a good discount. Were flattered by this! Choose warm glass Rehau profile, received i-glass as a gift, now it will not be cold in winter, and not hot in summer. A very nice gift! Thank you for such a warm welcome! Good luck and prosperity in your future career!

Great company! I ordered the decoration of the balcony in Leningrad. At first, I was pleased with the guarantee that the company provided, thereby instilled confidence =) Finishing was done quickly, on time. The work performed was very pleased, the workers did everything the way I wanted. We installed a sliding wardrobe on the balcony, replaced windows, made beautiful ceiling. In general, everything is great. But the best part is the discount I got :) Managed to save almost half of my money. And finally, they gave a heater. Some positive emotions! Thank you GK Expert!

Before the New Year, my wife and I decided to glaze the balcony. We were looking for a suitable organization for a long time, after much deliberation, we settled on the GK Expert company. The next day after the application was made, a specialist measurer came. We discussed all the nuances of interest with him, and with the help of the ipad we made a project. We decided to insulate a little more, with such a discount, we chose a laminate floor as a gift. After 5 days, the installers arrived, carried out the installation process very carefully, and removed all construction debris after themselves. Now we are thinking of changing the windows in the apartment, we will now turn only to you. Thank you!