Dampness appeared in the apartment: how to get rid of an unpleasant smell and prevent its reappearance? How to get rid of dampness in the house

high humidity in the house can be caused by various reasons, the main thing is to respond to this phenomenon in time and take all measures to combat mold and fungus on the territory of your own living space. The influence of mold is detrimental to the state of the walls of the health of residents. Therefore, having discovered dampness for a start, you need to find out the cause that caused it and take immediate measures to eliminate it. For this there are various ways, allowing to get rid of such an unpleasant phenomenon.

How to get rid of dampness in the house

Causes of dampness in the house

To determine the cause of dampness, you need to pay attention to the place where it is found. Finding a place where mold accumulates on the wall will make it easier for you to understand how to get rid of dampness in the house. If the wall facing the street turned out to be wet, then it is necessary to insulate it with a reliable material that is a heater and, thereby, provide thermal insulation. The result of the work done will not keep you waiting long.

What to do if the house is damp

If the mold accumulates on the ground floor and occupies only the lower part of the wall, then the point here is poor insulation between the foundation and the wall. The reason may also be damp basement. If pipes are leaking in it and there is constant humidity, then homeowners are doomed to dampness in their apartment. Poor ventilation in the house or its absence at all also leads to dampness and mold on the walls. AT high-rise building to deal with such a phenomenon is much more difficult than in own house, where everything is much easier to foresee even during construction. And you just need to take all measures for the installation of ventilation and installation insulating materials than then puzzle over how to remove dampness in a private house. Here it is necessary to create a ventilation system in the foundation.

Humidity ventilation in the basement

Great importance has wall and attic insulation, as well as underfloor heating equipment. Uniform distribution of heat throughout the housing and reliable system ventilation must be taken into account during the construction process. It is best to install windows in the house that open, then you can constantly ventilate the room. Previously, in all apartments it was mandatory to install ventilation vents in the kitchen, in the bathroom and in the bathroom. Such measures in rooms with a high level of humidity were urgently needed. In private houses, too, care was taken to protect the walls from dampness. There is an expression that the walls in the house must breathe, and air is necessary for normal breathing. If the air in the house is heavy, stale, then the walls will become covered with mold.

A mistake made during construction can cause asthma, tuberculosis and other serious illnesses in the residents of the house. Therefore, the homeowner must find ways to eliminate dampness in the house, as well as ways to prevent this phenomenon. Each homeowner, seeing dampness in the house, wonders what to do if the house is damp. Sometimes it happens that getting rid of such discomfort in the house is quite difficult and you have to try several ways to achieve the desired result. Therefore, it is always easier to prevent the occurrence of dampness on the walls than to deal with this unpleasant phenomenon later.

Dampness in the house photo

How to get rid of dampness in the house - ways

Whatever the reasons for the occurrence of such an unpleasant and dangerous phenomenon, with him, first of all, you need to fight with all existing ways. These days, there are a lot of products for removing mold from walls in the construction supermarkets. But if the cause of the occurrence is not in poor ventilation of the room, but is associated with improper construction of the building or with other, more significant shortcomings in the construction of the house, then these chemicals do not bring the desired effect.

They are especially ineffective in the case when dampness in the room has existed for a long time. years. Unfortunately, our houses are sometimes poorly heated, thin block walls let the cold in, the walls are lined with furniture, there is no ventilation. All these factors lead to constant dampness on the walls. And in houses where repairs have not been carried out for years, the roofs are also leaking, which adds even more moisture to the apartments.

Some apartment dwellers and home owners believe that air conditioning will save the situation. However, this device only drives damp air around the apartment, and does not get rid of it. Gives a much greater effect open windows with mosquito nets on them. If your house is damp, it is better to put plastic windows without partitions, then more sunlight enters the house.

How to eliminate dampness in the house

The fight against dampness, mold and fungus in the room is an expensive and demanding process. Therefore, you need to be patient and try to create comfort and coziness in your family nest. First of all, you need to remove the fungus and mold from the walls. This is best done with a quality antiseptic. On sale there is a sufficient selection of this tool for walls made of various materials.

Antiseptic against mold

If the walls are covered with wallpaper, then they must be removed, the plaster in the area of ​​\u200b\u200bthe areas affected by the fungus is also removed. To protect yourself, you must wear a mask. The walls must be completely cleaned of mold before proceeding with their treatment with a special tool. In addition to antiseptics, the surface can be treated with creosote. You can also dilute stationery glue in a ratio of 1:4. Urea is also used to treat walls. All these funds are applied only to areas affected by dampness. Before applying the mixture is brought to a temperature of 50 degrees. After applying protective agents against dampness, the walls should dry well.

When you manage to get rid of the fungus on the walls, create conditions in the apartment or house so that it never appears again. To do this, your room must have a sufficient amount of sunlight and fresh air. No need to purchase a lot of furniture and make it all the walls in the room.

Remove some houseplants such as geraniums and violets that add moisture. You can get rid of dampness and mold only by setting a normal level of humidity in the house. No need to dry wet laundry in the room; when repairing, try to get dry building mixtures. An excellent effect is provided by the insulation of facades with the help of polystyrene foam and other types of insulation. Good to keep open interior doors for normal air circulation. But the doors to the kitchen must be tightly closed, especially when dinner is being prepared there. Equip the hood above the stove and keep the windows open in the kitchen.

How to remove dampness in a private house

Provide good ventilation in the bathroom and toilet. Try all methods of dealing with dampness to keep yourself and your family healthy. If the apartment is poorly heated, buy heating convector which will dry the walls well warm air. When wet cleaning, wipe the floor well. If the house already had a fungus, then constantly monitor the condition of the walls after treatment.

How to reduce humidity in the apartment

But when, having tried all the methods of dealing with dampness, you have not achieved a positive result or simply do not have the time and opportunity to deal with this issue, contact construction company and they will send you good specialists who successfully deal with such a problem. These workers use the most effective methods fight against such a negative phenomenon and know how to get rid of dampness in the house.

High humidity in the house can be caused by various reasons. Almost every second owner of an apartment and a private house faces this phenomenon. Moisture causes mold.

Therefore, excess moisture in the house must be dealt with. The source that causes this phenomenon should be found and appropriate measures should be taken. It is worth saying that the fungus and mold in the house appear just because of the high humidity. In addition, dampness worsens the health of all residents living in the house. Therefore, today the portal will talk about how to get rid of dampness in the house. folk remedies?

High humidity in the house: how to deal with it

Why is there dampness in the house?

The cause of dampness is directly sought on the territory of the house itself. To quickly get rid of dampness in the house, you need to find a place where mold accumulates, and only then think about what can be done in such a situation. If a increased dampness exposed to the wall facing the street, then it must be trimmed with a reliable insulating material. Mold does not only appear in private homes. Quite often, mold occurs in modern apartments. Very seriously, this problem worries the owners of apartments on the ground floor. Usually in such rooms, mold forms in the lower part of the walls. This contributes to a number of unpleasant reasons. It could be:

• Poor insulation of the foundation with the wall.
• Damp basement with leaking pipes.
• Bad ventilation.

It is worth saying that it is much easier to eliminate dampness in a private house. After all, you just need to organize proper ventilation or install thermal insulation materials. AT apartment buildings it is very difficult to deal with this phenomenon. Here, the main reasons for the appearance of this factor are hidden in the first stages of construction. And if the developer misses important points, then the apartment will always deliver unpleasant problems to its owners. Moreover, being in this room will adversely affect the health of all household members. People who are constantly in an apartment with high humidity can get sick: asthma, tuberculosis and other more serious diseases.

What ways will help get rid of dampness in a private house

Now it's time to understand what to do with dampness at home and how to get rid of this unpleasant phenomenon in your home. Dampness in the house must be dealt with without fail.

In this case, you need to use all modern methods.

• So, a special tool that can be purchased at any supermarket will help get rid of mold and dampness in the house. However, this remedy may seem ineffective if the cause of the mold lies in other factors. For example, the use of special tools will be useless if there are problems with ventilation or ventilation in the house. If the wrong construction of the building was carried out, then the remedy also cannot bring an effect. After all, you need to fight the main causes of mold.
• Mold on the walls in the house can form due to poor heating. Indeed, the walls of the blocks are able to pass the cold. In addition, they are crowded with bulky furniture that does not allow heat to pass through. All these reasons contribute to the formation of mold, which releases dampness and unpleasant substances into the air for years. Some people believe that such problems are very easy to solve with a special product from the supermarket. However, it is not. Here you will need cardinal methods. Even an air conditioner that will simply drive damp air around the apartment will not bring the desired effect. But there is no need to despair! After all, if the house is constantly damp, you just need to install plastic windows that will not have partitions. The window will allow natural light to constantly enter the house. In addition, with such an item it is possible to carry out high-quality and constant ventilation of the room.
• Fighting mold is very difficult. And this should be remembered by every homeowner with such an unpleasant problem. In this case, you will need not only patience, but also a lot of effort. To make your family nest comfortable and cozy, you need to remove fungus and mold from the walls of the house. For such work, you will need to purchase a high-quality antiseptic that will clean the walls of the fungus and make them aesthetic again.
• If the walls of the house are covered with wallpaper, then they are removed. In addition, the plaster affected by the fungus is removed. In order not to harm your health, all work must be done in a mask. Walls before treatment with an antiseptic must be cleaned of fungus and mold. Only after that they can be treated with an antiseptic and creosote. For the treatment of walls, other compositions are also allowed. For example, you can dilute stationery glue with water in a ratio of 1:4. It is allowed to treat the walls with urea. All of the above funds should be applied only to the affected areas of the walls. Before applying, the affected areas on the walls must be heated to 50 degrees. After finishing work, the walls must dry completely.

How to get rid of dampness in the apartment and in the house? This question will be relevant at any time. As mentioned above, this process is difficult and painstaking. In addition, after removing the mold in the room, it is necessary to create special conditions, which will prevent the formation of mold and increased dampness.

So, to prevent the appearance of mold and dampness in the apartment will help sunlight and Fresh air. In addition, you need not to force all the walls in the room with furniture. Some plants can increase the humidity in rooms. Therefore, it is necessary to remove from the room where there is high humidity: geraniums and violets. If a normal level of humidity is observed in the dwelling, then mold and fungus can be forgotten on long time. Experts do not recommend drying wet clothes in the apartment and house. In addition, for repairs, you need to purchase dry building mixes.

A good effect can be given by the insulation of facades with a heater or foam. Dampness in an apartment is quite common. Therefore, everyone should know how to get rid of this phenomenon. In a room with high humidity, normal air circulation should occur.

Therefore, it is better to keep interior doors open. But the doors to the kitchen should be closed during cooking. In this case, it is recommended to use a hood and vents to ventilate the kitchen.

For high-quality ventilation of the bathroom and the bathroom, you need to equip good ventilation. There is no need to invent something new and look for expensive solutions.

findings

To maintain good health and well-being, it is necessary to remove from the rooms: mold, fungus and high humidity. In addition, you need to monitor the condition of your home and prevent this problem from occurring. For example, if an apartment or house is equipped with low-quality heating, then you need to purchase a heating convector that will dry the walls with warm air. During wet cleaning you should wipe the floor well and monitor the condition of the walls on which the appearance of the fungus has already been recorded.

If all methods to combat the fungus have already been tried, if not observed good result, or there is no time at all to deal with such problems, you need to contact a special company that will send competent employees to deal with this problem.

When dampness appears in the house, you need to start fighting it immediately. Dampness is insidious, today it's easy excess moisture, and tomorrow already harmful mold. And as a result - a decrease in immunity, lung diseases, colds, allergies. In addition, dampness is accompanied by the appearance of various insects that love moisture: wood lice, dust mites, centipedes.

But dampness is dangerous not only for humans, the house and furniture also suffer greatly from it. Spots appear on the walls, ceiling, wallpaper swells. If you do not start drying and airing in time, the smell of dampness will be absorbed into the furniture, this will be especially noticeable in wooden products, for items containing leatherette, and textile items. AT advanced cases things can start to deteriorate irreversibly.

Causes of dampness

Dampness can appear in the house in two ways.

• Come outside. If the walls, roof, floor have a construction defect, then pretty soon moisture will appear in the house, especially during the rainy season. Or the neighbors upstairs had a flood. Dampness can come to the inhabitants of the first floors from the basement. Residents panel houses panel joints become potentially dangerous, you need to constantly monitor the condition interpanel seams.
• Educate inside. The first is condensation. Infrequent ventilation, with frequent work with the formation of high humidity - for example, when cooking and washing. Poorly insulated rooms. In addition, leaking pipes in the bathroom, in floors. A large number of house plants and the presence of an aquarium also affect the humidity in the direction of its increase.

Dampness in a private house

A private house is much more prone to dampness than a multi-storey one. Moisture approaches the house from all sides. This includes both groundwater and rainfall. It is necessary to constantly monitor the waterproofing of the basement, the tightness of window and door frames, and the serviceability of drainage system and the condition of the roof.

As a rule, dampness comes to the house in the autumn. When, with the onset of cold weather, people very rarely open windows for ventilation, the sun does not warm the house. Furnace heating perfectly dries the air, but it is not enough.

It is very important even during the construction of the house to comply with the entire technology of thermal insulation of walls and floors. Violation of technology in this matter can lead to freezing of the walls, to the accumulation of moisture inside the walls. And if the house is wooden, then this will create many problems. Mold will begin to grow, from which the tree will gradually rot. With poor floor insulation, cold and moisture will come from the basement, keeping the house high level humidity.

How to get rid of dampness in the house

The main thing is to give moist air get out of the room. Regular ventilation quickly and effectively reduces humidity.

Forced ventilation. Do not forget to periodically clean it from dust.

Household dryer. This device is very effective in closed small spaces, but it makes sense to acquire it if it is problematic to ventilate this damp room. How much moisture the dehumidifier will drive off in 2 hours can be achieved with elementary ventilation in 10 minutes.

Insulate cold walls, floors, repair the roof in time, eliminate leaks.

Adjust the heating system during the wet period.

Ventilate the tub properly after using the shower.

When cooking, turn on the ventilation or open the window to let excess moisture out. Especially when boiling liquids in large pans without a lid.

Try not to dry clothes in the house. Either hang it in a well-ventilated area, or close to the ventilation turned on. At a constant high humidity for drying clothes, if possible, purchase drying cabinet. Especially if you have to wash often and a lot. But from washing vacuum cleaner better to refuse.

Control the humidity level. To do this, purchase one of the following instruments: hygrometer, barometer, integrated weather station. It is necessary to fight for lowering the humidity from 70%. A comfortable level of humidity for a person is the range of 40-60%. But keep in mind that if mold is already living in your house, then it will begin to grow from 50-55%.

Special remedies for dampness

In order not to deal with the consequences of dampness, it is better to take measures to prevent its occurrence. This will help special means, which are used at the construction stage or during repairs. This is different kinds waterproofing, antifungal primers, wallpaper glue with a fungicide in the composition.

If dampness still appeared in the house, then some try to fight it by placing containers with calcium chloride in the form of powder or salt in the corners, and bags of silica gel are placed in wardrobes with clothes. However, if you do not eliminate the main reasons for the increase in humidity, using these products is like carrying water in a sieve.

For a full-fledged life, a person needs air with an optimal level of humidity. It is not uncommon for this level to rise in the bathroom, kitchen, living room or vestibule. The owners grab their heads, not knowing how to get rid of the smell of dampness and high humidity that has appeared. In addition to the fact that an unpleasant odor permeates clothes and wooden elements decor, mold appears on the walls, which spoils the whole impression. To cope with the problem in a short time, it is necessary to adhere to practical recommendations.

Optimum humidity level

It is generally accepted that the dwelling should have humidity, the indicator of which ranges from 50-60%, not higher. To measure the microclimate, you need to use a device called a hygrometer. AT summer time year, it is possible to reduce the humidity level to 35-40%, this feature is achieved for obvious reasons.

It is known that the human body equally badly tolerates both excessively humid and arid climates. People who use split systems should be extremely careful. The air conditioner sucks in moisture, causing a decrease in the optimum value. However, if you often dry clothes in the living room, and not on the balcony, the split system will become a lifesaver.

Reasons for high humidity

1. High humidity occurs for many reasons, one of them is considered to be the lack of both natural and artificial ventilation. If there is air circulation, then it is worth checking how well it works.
2. It is not uncommon for the humidity to rise above the permissible limits for the reason that the neighbors living above heat the apartment from below. Dampness accumulates in corners and cracks, provoking the appearance of mold.
3. To date, not every developer can be called conscientious. Some save on material, others hire workers with insufficient qualifications. High humidity appears due to poorly sealed seams from the street part of the wall.
4. If we talk about the house, in most cases the basement is often flooded due to the large amount ground water. From lower tier moisture rises to the first and second floors, while being accompanied by an unpleasant odor.
5. The modern design of many living spaces involves concealment sewer pipes various decorative panels. For this reason, if a water leak occurs, the owner cannot eliminate it in time.

The consequences of high humidity

Important attention must be focused on health, which deteriorates due to high humidity.

1. In such conditions, the human body is not able to cope even with the most banal cold syndromes, what can we say about serious diseases. If you are constantly and for a long time in a humid environment, a banal cold can develop into something more.
2. In addition to weakening the immune system, a humid microclimate causes allergies, eczema, skin rashes, insomnia, runny nose, muscle and joint pain. Also, high humidity contributes to the development of apathy, general fatigue, depression.
3. It is not uncommon for a fungus that has appeared to cause the development of chronic diseases. The elderly and children are most susceptible to such reactions. In the first category, the protective functions of the body do not work to the full, in the second - the body is not yet fully formed.
4. If the air humidity exceeds the optimal limits, a caustic and bad smell mold. The stench eats into the furniture upholstery, floor soft coverings, clothes, towels, linens, mattress and pillow.
5. Due to high humidity, the seams of the room turn black, indicating the development of mold. With each passing day, the fungus infects an increasing surface, under the threat of walls, ceilings, cabinets, window frames etc.
6. If high humidity persists long time, accelerated spoilage of food products (baked goods, vegetables, fruits, flour, cereals and legumes) begins.

1. Air Dryer. by the most the best option To combat high humidity, it is considered to be the use of a dehumidifier. The pricing policy depends on the specific manufacturer, the power of the unit and its model. You can buy the device in Vse dlya Doma stores, as well as in electronics hypermarkets. It is worth clarifying that the more productive the unit, the faster it will cope with high humidity. If possible, purchase a device with a regulator and a table that displays the level of dampness. Such a function will allow you to save on electricity and not dry out the air.
2. Heating radiators. You can get rid of excessive moisture in the room with the help of heating radiators. Batteries are present in every apartment, but it is not always possible to use them (the exception is the summer-spring period). If you notice that dampness persists for a long time, heat the room periodically. During a kind heat treatment the fungus dies, the air becomes much drier. Turn on the heating only in the cold season, avoid sudden jumps temperature regime, because of which the windows sweat.
3. Fresh air. It is known that a humid environment is afraid of fresh air, but only if the ventilation does not occur on cloudy and rainy weather. Make it a habit to open windows 3 times a day, leave for a quarter of an hour, if possible longer. If possible, keep the window open at all times, closing it only in case of rain outside. To make ventilation much more efficient, install plastic windows that open upwards (micro-ventilation). Such a move will eliminate the likelihood of drafts and remove moisture.
4. Sugar and salt. The listed products perfectly absorb moisture, but, as a rule, they are used extremely rarely. Agree, it is not very convenient to keep a five-kilogram bag with a loose composition in the middle of the room, also in the open state. The option is useful in the fight against moisture in small rooms, such as a pantry, vestibule, bathroom. It is enough to pour salt or sugar into the basin, and then take it to the room, do not forget to stir occasionally.

Preventive actions

1. Inspect sewer pipes and heating radiators, find out if there is a leak. In this case, call the wizard or troubleshoot on your own.
2. If the yard is sunny and warm, ventilate the room constantly. Do not sit in an apartment with closed windows long time.
3. The air conditioner absorbs some of the moisture from the room. In addition, the split system eliminates the smell of dampness and prevents mold from infecting larger areas.
4. Equip your kitchen with a hood. Turn it on every time you cook, especially if you prefer to boil or stew foods.
5. Check traction ventilation system, clean it of dust and foreign debris. Perhaps it is the ventilation that is causing the unpleasant odor.
6. Choose for yourself houseplants who don't need abundant watering. The cactus is considered the most optimal, put 3 species in each room with a suffocating smell.
7. It is known that natural materials absorb from excess moisture. During cosmetic repairs give preference to products of this kind, give up synthetics.
8. Look for absorbent preparations that absorb excess moisture. Great option serves as a means of "STOP moisture", it can be purchased at any hardware store.
9. AT winter time of the year, install an additional heating radiator in the apartment or get by with the simplest wind blowing "Breeze".
10. If possible, dry clothes on the loggia or balcony. Otherwise, keep the windows open throughout the drying process (important for warm and sunny weather).

It is quite difficult to get rid of high humidity in the apartment, if you do not have knowledge regarding the available methods. Ventilate the room more often, install air conditioning, heat the apartment. Get a dehumidifier, turn it on at least 4 times a week.

Video: what is the danger of high humidity in apartments

Before you decide how to get rid of dampness in an apartment, you need to find out whether moisture comes from outside or is generated inside the room.

To do this, take a small piece of glass, press it firmly against the wall and hold it for a while. If, after tearing off the glass from the wall, it is wet, you can be sure: dampness comes from the outside. Otherwise, it is necessary to look for an internal cause.

What is the reason

What can cause high humidity in the apartment? First of all, the lack or poor performance of ventilation. First, check if you covered it with wallpaper or when installing kitchen appliances.

It is easy to eliminate such a reason: cut out the desired square on the wallpaper in place of the ventilation grill or make the correct outlet for household appliances.

Perhaps your neighbors are heating you upstairs. Inspect carefully the ceiling throughout the apartment, especially in the bathroom, toilet, kitchen. When identifying wet spots on the ceiling or walls adjacent to it, go to a neighbor to sort things out.

The accumulation of moisture in your room could be due to poor thermal insulation of the walls, flaws in the seams of housing construction. In this case, these shortcomings must be eliminated.

How to prevent

If you dry a large amount of laundry at home, high humidity in the apartment cannot be avoided. It’s worth thinking about, maybe there is a way to stretch the laundry in time, and use the balcony instead of the bathroom to dry the laundry.

With chronic dampness in the house, it is worth buying a dehumidifier, preferably with an automatic mode of operation. It will independently maintain optimal humidity in the apartment.

If the source of dampness is in the bathroom, install an electric one there. It will dry not only towels, but also the air in the room.

Any damp room should be periodically heated, dried and ventilated. This must be done even in winter. Use when cooking in the kitchen. It will successfully cope with the absorption of moisture formed during cooking.

First floor

The reason for the dampness in the apartment on the first floor is the flooding of the basement. If this happens all the time, and complaints to the housing office do not give results, you should think about installing waterproofing. But she does not give a full guarantee against dampness.

The apartment on the ground floor also needs additional heating.

How the room is heated - by the rays of the sun, warm air from the air conditioner or underfloor heating with a built-in electric heater - does not matter. By heating the apartment, you will expel moisture from it.

If you are thinking about how to get rid of dampness in an apartment on the 1st floor, you should know: the flow of moisture from basement increases sharply in spring and autumn.

Therefore, if correctly placed in the room heating appliances, the problem will be solved. You should not be afraid of energy overruns: you will need to turn them on only twice a year, in spring and autumn, for periods lasting a maximum of a month.

Fifth floor

If you are facing the opposite problem and do not know how to get rid of dampness in an apartment on the top (stained) floor, perhaps these tips will help you.

In Khrushchev on the 5th floor, the cause of dampness is usually external. The high humidity here is a direct consequence of the lack of gable roof, wall insulation, low-quality interpanel seams, cast iron batteries heating with extremely low efficiency.

Oddly enough, technological progress only exacerbates these problems. The design of the Khrushchev suggests that fresh air constantly enters the room through the cracks in the windows, and goes outside through the ventilation shafts.

Installing plastic windows closes the flow of air from outside. And the ventilation on the last floor of the five-story building does not work well, since the lower floors are mainly ventilated in such a structure. As a result, on the 5th floor there are always corners and rivers on the windowsill.

To solve the problem, it is necessary to install an alpine window. This is a system of valves punched into the walls of each room, combined with a powerful hood.

Fresh air enters the apartment through the valves, the hood draws out the exhausted moist air from it.

It is easy to verify its effectiveness in winter: large icicles are necessarily formed on the valve pipes in frosts outside. This is the moisture from the air in your apartment.

Folk remedies

Is it possible to get rid of dampness in an apartment with time-tested folk remedies? Let's turn to the experience of our grandmothers.

Salt, sugar, coffee grains perfectly absorb moisture from the air. If you place open bags or jars with these products in the corners of the room, in cabinets, the apartment will “dry out”.

For the same purpose, the furniture in the room should be regularly wiped with a weak solution of potassium permanganate. Wipe dry with all wet surfaces. Thoroughly ventilate the room after each cleaning.

Against mold

The mold must be scraped off the wall, then the walls should be smeared with a solution blue vitriol or a special antifungal mixture.

You can use bleach, bleach, soda, vinegar, tea tree oil and ordinary soap solution for this.

Must do at home high-quality ventilation- fresh air will not allow mold to develop.

When cooking, it is better to use forced ventilation. It is also necessary to repair the leaking water supply in time, do not supercool the room, and wring out the laundry well before drying.

For the winter follows a special cord in a cotton sheath or porous pads. Fill gaps in frames with plain window paper.

And from replacement wooden windows on plastic with problems with dampness it is better to abstain.

If you still decide to install plastic windows, think over the ventilation system. Fresh air will not be able to get to you through the window now. And not everyone will dare to open the window in a twenty-degree frost.

Dampness and repair

If you started a renovation and intend to radically solve the problem of dampness in the apartment, it is advisable to use natural materials for it. They tend to absorb excess moisture from the air.

When repairing, you must also apply waterproofing materials. Include antifungal ingredients in grouts.

Think ahead about the future installation of furniture. It should not be placed close to the walls, be sure to leave a gap.

To eliminate the causes of dampness, it is necessary to thoroughly deal with floor insulation, external and internal wall insulation. The walls must be wiped with a bleach solution and re-plastered.