Installing a chandelier on a plank. How to hang a chandelier on a concrete ceiling. Little negligence - big problems

Hello, dear readers and visitors of the site.

After buying a chandelier, the question always arises of how to install it. In this article I will tell you how to hang a lamp or chandelier without calling specialists.

There is nothing complicated in this and you can easily cope on your own. But some subtleties and nuances need to be mentioned.

There are several ways to mount and install the chandelier in the ceiling:

• on a metal hook
• on a bracket or bar
• directly to the surface

Consider each mounting method in more detail.

Installing a chandelier with a hook

This is the simplest and convenient way chandelier fixtures. We hang it on a metal hook pre-installed on the ceiling. In my example, an old-style metal hook is shown, installed during the construction of the house.

1. How to hang a light chandelier

If the chandelier is not heavy and weighs up to 3-4 (kg), then you can use just such a metal hook with a thread.

Using a perforator, we drill a hole in the ceiling, insert a plastic dowel into it and screw in the hook. The fixture for the chandelier is ready.

Also, using a metal hook with a thread, you can install a chandelier in the ceiling with wooden floor. The hook just needs to be wrapped (twisted) in wooden base ceiling.

I would like to draw your attention to the following. Installation of a hook into a plasterboard ceiling is prohibited. In this case, the metal hook must be attached to concrete base ceiling.

2. How to hang a heavy chandelier

If the chandelier is heavy and weighs more than 5 (kg), then it is better to use special anchor bolts diameter from 10 sq. mm. with spreader hook.

We drill a hole in the ceiling of the required diameter. After that, we insert the anchor into it and tighten it until it stops. Such fastening of a chandelier is very reliable.

Chandeliers that are designed to be mounted on a hook have a special decorative cup.

The cup moves freely in height and is fixed in top position to hide places .

Mounting a chandelier with a bracket (bar)

And now we will look at how to install a chandelier without a metal hook. I consider this method of fastening somewhat more complicated than the previous one, but not so complicated as to resort to the paid services of specialists.

Included with the purchased chandelier is a special metal bracket or bar. We install 2 screws into this bracket or bar, adjusting the distance between them, and then tighten them with nuts. After that, we fix the bracket on the ceiling with a puncher and two dowel-nails.

Previously, a chandelier on a metal hook was installed at this place. Bought new chandelier fastened with a bracket, so I bent the hook to the ceiling, which you can see in the photo. You can generally cut the hook, but it doesn’t bother me at all in this position.

Tighten the two fixing decorative nuts.

The chandelier is installed and ready for use.

Now I will not dwell on this, because. this is the topic of a separate article. Read on for upcoming issues.

P.S. So, in this article, we got acquainted with how to install a chandelier using metal hooks, brackets and directly to the surface. Now let's move on to connecting it. Read about it in my next articles.

After reading the title of the article, surely someone will definitely say - “why about e so-and-so write, with such work any landlord himself will be able to cope. Yes, of course, the installation and connection of a chandelier does not belong to the work of the highest category of complexity, however, these processes also have specific nuances, on which, by the way, the safety of living in an apartment depends.

The chandelier is connected to electricity, and all electrical appliances, if they are incorrect installation become source of danger - electric shock or even fire. In addition, this lighting fixture is often quite massive, and can cause a lot of trouble if it is not securely fixed to the ceiling. Thus, the whole complex of problems related to how to connect a chandelier with your own hands is conditionally divided into two directions - providing correct connection it to the mains and its reliable and most beautiful placement on the ceiling plane.

find out useful information, from our new article.

It is clear that the vast majority of apartment owners choose this lighting fixture, relying primarily on its external design, so that it matches the overall interior design of the room. However, at the same time, one should not forget about some other aspects of the choice.

• The total luminous power of the chandelier should correspond to the size and type of the room for which it is intended. There are certain illumination standards, which can be summarized as follows:

- For rooms where soft diffused, subdued light is required ( typical example- bedroom) should be based on 10 ÷ 12 W / m² area.

— For rooms with an average level of general illumination (kitchen, bathroom, bathroom) or where it is planned to install additional lighting for specific workplaces (study or nursery) the norm will be from 15 to 20 W / m².

- For rooms with bright illumination (living room), this indicator is taken equal to 20 W / m².

In accordance with the calculated power, a lighting fixture with the required number of horns should be selected. Important nuance- in no case should you increase the overall illumination using more powerful lamps than allowed by the manufacturer. The material of ceiling lamps, cartridges, the cross section of internal wiring may not be designed for increased loads, and this will lead to damage to the device or even a fire hazard.

• Dimensions lighting device should be in harmony with overall dimensions premises. A huge chandelier will look ridiculous in a fairly cramped room, or, conversely, too small will simply get lost on the plane of the ceiling of a vast hall. Designers recommend proceeding from the following considerations:

- The optimal diameter of the chandelier can be approximately determined by the formula:

D = ( L+ S)×10

D- chandelier diameter in centimeters

L and S- the length and width of the room, respectively, in meters.

So, for example, for a room with dimensions of 5 × 3 m the best option there will be a chandelier with a diameter of 80 cm.

• The type of chandelier you choose depends on the height of the room. If the ceilings in the room are low, about 2.5 m, then it is better to give preference to the ceiling version of the lighting fixture, so that there is at least 2.0 ÷ 2.2 m from the floor to it. Hanging option will be appropriate in a room with high ceilings, and here the length of the suspension will be determined only by considerations of aesthetics.
• Be sure to compare the type and material of the ceiling with the weight of the chandelier and the method of hanging it - this will be discussed below.
• Chandeliers are most often sold unassembled, so special attention is paid to completeness, compliance with the threads on all collapsible parts, integrity decorative elements. Be sure to check for clear and clear instructions for product installation.
• Unfortunately, the lighting market is literally oversaturated with cheap and low-quality goods and outright fakes for famous brands. These products may use low-grade plastic cartridges that are not designed for high temperatures. They will issue a counterfeit poor-quality installation of the electrical part, twisting of wires, lack of terminal connections, etc. Often you have to independently carry out wire switching, their desoldering and insulation in accordance with all the rules. In particular, this applies to "fancy" chandeliers with LED additional circuits, power supplies or current transformation, devices remote control etc . To avoid taking on these extra hassle, it is better to choose a product with a really high-quality cable and electrical "stuffing", require assembly and testing of the product in the store.

We deal with the wires on the chandelier and on the ceiling

We will not consider in this article complex options with chandeliers stuffed with electronics - their installation in most cases will definitely require the services of an appropriately qualified specialist. But everyone should be able to connect an ordinary chandelier on their own.

First of all, a few theoretical questions from the field of home wiring. As you know, the power supply in our area is organized with a standard voltage of 220 V and a frequency of 50 Hz. Household wiring is carried out on two wires - phase and zero. If a ground loop is provided in the house (in modern housing this becomes a necessity and, most often, this issue is foreseen in new buildings), then a third wire connected to the ground bus is included in the wiring.

There is a generally accepted color marking of wires of a single-phase electrical network:

A characteristic nuance - if the neutral wire always has a blue or blue color, and the ground contact is yellow-green, then the color of the phase wire may vary:

Often, several phase wires one or more colors - this is used, including when connecting lighting fixtures, to switch different modes their work:

Ideally, both the chandelier and the house wiring should use this color coding. However, practice shows that in both cases this rule is not always observed. For example, in old houses, aluminum or copper wires in single color insulation. In this case, you will have to deal with them yourself.

Particular attention should be paid to safety measures when working with electrical wiring. It is strictly forbidden to touch bare wires with bare hands, unless the general power supply is turned off. You must wear shoes with rubber soles. To work under the ceiling, you need to provide a reliable foundation - an unstable stool or bedside table can lead to loss of balance, falling and injury. For these purposes the best option there will be a stepladder mounted on a rubber mat.

1. So, the easiest option is a cable with two wires coming out of the hole in the ceiling. It is clear that one of them is phase, and the other is zero. By existing rules zero should go directly to the junction box, and phase should be interrupted at the switch. Nevertheless, it doesn’t hurt to check - very often electricians “did not bother” with these issues.

• To check you need to have special device– phase indicator. Most often it is performed in the form of a screwdriver with a transparent body, although modern models may have another design, including even with an indication of the magnitude of the phase voltage.
• First of all, it is necessary to completely de-energize the room or the entire apartment on the switchboard. This is necessary in order to thoroughly clean the wires from insulation and oxides to a length of 5 ÷ 8 mm. After stripping, the wires are bred to the sides as much as possible to prevent their short circuit. After that, turn on the machine on the shield.
• Then, with the switch in the off position, both wires are checked in sequence. None should show the presence of a phase. If there is a phase on one wire, then the wiring in the house is not done correctly - on the switch, apparently, “zero” is interrupted. It is very difficult to change anything in this case - it should just be borne in mind, exercising special care in further work.

• The phase is checked in the same way when the switch is in the on position. As a result, it will be revealed phase wire, which can be marked in a certain way (with a marker or colored tape).

2. If a switch with two or more keys is installed in the room, then from the ceiling holes should be like the appropriate amount phase wires. The check is carried out in the same way as described above, with the marking of each phase separately, in accordance with the location of the switch keys.

A similar check should be carried out even if wiring is installed with color coding- just to eliminate the mistakes of an electrician who once installed it.

3. Now - about the cable part of the chandelier itself.

• The easiest way is when the chandelier is one- or two-three-horn, without dividing them into groups. All wires from the cartridges are assembled into two contact groups - zero and phase. If there is a ground wire, then it is usually attached to the metal body of the lamp.

• In the case when it is necessary to divide the horns with cartridges into two or more groups, then all the blue "zero" wires are connected into one bundle, and the phase wires are divided into several, according to the number of keys on the switch.

Very often, this can be seen quite clearly on chandeliers, and such switching will not be difficult.

The simplest case: all the wires are in full view

• In both cases, the bundles of twisted wires should be thoroughly soldered and placed in a screw terminal block or separate spring terminals.

• It is somewhat more difficult to understand when the device of the chandelier does not make it possible to visually understand its internal wiring. However, here you can figure it out by ringing all the outgoing wires using a multitester. To do this, you can sequentially screw an incandescent lamp into the cartridges (an energy-saving fluorescent lamp will not help in this case), and empirically find out which horn is powered from which wire. After that, it will be easy to distribute the horns into groups.

For "call" hidden wires you need a multitester

There are other methods for determining the internal wiring of a chandelier, based on calculating the resistance of a circuit with lamps of the same rating screwed into all cartridges, but in practice it is still probably easier to just ring each horn.

So, the result of checking the chandelier circuits and fixed wiring in the room should be a clear understanding of the circuit, prepared for switching and marked wires on the ceiling and a group of contacts on the lighting fixture itself.

Video: wiring diagram for a five-arm chandelier to a two-gang switch

Mounting a chandelier on the ceiling of a room

If everything became clear with the electrical part, it is necessary to ensure that the chandelier is securely fastened to the ceiling. The technology of work depends on the design of the chandelier, and on the type ceiling covering.

Hanging a chandelier on a hook

This is an old and proven method of mounting chandeliers, which have a special loop, ring or hook for this purpose.

In old high-rise buildings hanging hooks were installed in the ceiling holes at the construction stage. If it is worth it, then the problem is less, however, it does not hurt to check it for strength. To do this, it is necessary to hang a load with a total mass twice the weight of the chandelier planned for installation. If such a load is easily maintained, then there should not be any special concerns.

But what if the old hook is unreliable or its condition does not inspire confidence that it will withstand the load? No problem, you can install it yourself.

With wooden ceiling there should be no problems in principle - a hook-screw is easily screwed in there.

With concrete slab overlaps can be various solutions:

— You can hang a hook on a transverse steel rod, which is inserted into the cable channel of the plate. In this case, care must be taken not to damage the wiring passing there with the rod.

- Another option with an old hole in the ceiling is to insert a hook with a “butterfly” lock into it. Having passed into the cable channel, the “wings” of this fastening will straighten and create the necessary support, and all that remains is to fix the entire suspension with a washer and nut.

Hook with a spring retainer - "butterfly"

- If this option is not possible, for example, in the case when there is no “regular” opening for the hook, it will be necessary to drill in concrete floor a hole for a plastic dowel, but still better - for a metal anchor with a ring or hook.

Before drilling, it is useful to evaluate the direction of the wiring from junction box to the exit on the ceiling, so as not to accidentally break the cable with a drill or break its insulation.

If the internal cavity of the plate is caught during drilling, a special metal dowel for hollow structures - with screwing it in, a “skirt” is formed that securely holds the fastener in the ceiling.

After installing any type of hook, it should be tested for load - as described above. After that, it is recommended to insulate the protruding metal part by wrapping it with electrical tape or putting it on heat shrink tube appropriate diameter, followed by heating.

If the hook is reliable, you can hang the chandelier for a regular mount. Be sure to turn off the general power supply of the room in order to connect the contact part. The wires are connected by terminal connectors - twisting is not allowed, as sparks can occur on them with melting of the insulation. The connection is carried out in full accordance with the wiring diagram, about which it was written above.

Place contact connection wires and suspension on the hook is usually closed with a decorative glass (cap).

After completing the installation, turn on the power supply at the panel, then at the switch, in order to immediately verify that there are no short circuits. It does not hurt to check the absence of a phase on the metal body of the chandelier with an indicator. If everything is fine, then when the switch keys are turned off, the necessary lamps are screwed or inserted into the cartridge and the practical functionality of all chandelier horns is checked in all switching modes.

After checking, you can proceed to the final installation of the chandelier - installing shades, hanging all removable decorative parts, etc., according to the assembly instructions attached to the product.

Installing a chandelier on a mounting plate

Many produced chandeliers, especially designed for low rooms, are not hung on hooks, but are installed using screw fasteners on a special mounting plate fixed to the ceiling. This greatly improves the reliability general installation, since the load is evenly distributed over several attachment points.

The design of the mounting plate can be different - it all depends on the specific model of the chandelier and its weight. The bar can be straight or curved, with brackets for fixing the body of the lighting fixture, or with protruding studs or screws.

Particularly heavy chandeliers can be supplied with cruciform planks or in the form of a reinforced I-profile.

The bar may have a hole with the edges covered with an insulating sleeve for the passage of wires coming out of the ceiling. You can place the bar in the immediate vicinity of the cable outlet - the body of the installed chandelier will hide both the hole in the ceiling and the wiring.

The mounting plate is fixed to the ceiling plane different ways depending on specific conditions. In fact, this is described above, with the only difference being that instead of dowels with a ring or hook, ordinary ones are used, with a clamping head “under hide».

As well as when using a hook, the reliability of fastening under load must be checked.

The mount must be checked under load - in order to prevent such situations

Quite often, a situation occurs when the location of the dowels too close to the old hole in the ceiling does not ensure the reliability of installation - the edge of the concrete may crack or crumble. So that optimal choice fasteners and installation sites still remains with the direct executor of the work.

Fastening the chandelier itself to the mounting plate can also have its own characteristics. Perhaps, in this case, help is required - the lamp will have to be held on weight while the cable part is being switched. After the wires are connected, the body of the chandelier is attached to the bar with decorative nuts or screws.

Further work on performance monitoring and final installation is no different from what was described above.

Features of fastening the chandelier to the plasterboard ceiling

By by and large, you should plan the placement of the chandelier even before its installation. In this case, no problems are foreseen - one or more additional metal profiles for attaching a mounting plate or installed a hook, which will then be easy to build up with a chain or rod. AT drywall sheet a hole is immediately marked and drilled in the right place for the exit of wires and a hook.

But what if this question of hanging a chandelier arose later?

• In the event that the lighting fixture is hanging type, it is impossible to install the hook directly in the GVL - its strength is unlikely to be enough for point load. You can do it like this:

A hole is drilled in the ceiling with a diameter smaller than the decorative cap of the lamp.

Exactly in the center of this opening, a hole is drilled in the floor slab along the anchor fastening with a long drill installed in a puncher.

An anchor is inserted with a long threaded stud and is fixed to the limit in the hole made, so that the pin goes out, beyond the plane of the drywall.

An eye nut is screwed onto the protruding end of the stud, to which the chandelier itself will later be hung. The excess hairpin is carefully cut off with a hacksaw.

Spring "butterfly" with a hairpin

If there is a void or an old hole in the ceiling - everything same way, as when working on a conventional ceiling, only the fasteners do not have a ring, but a long threaded part, so that it comes out.

• If the chandelier is a console type, that is, it is installed on a mounting plate, then a lot depends on its mass.

- In the case when the total weight from the fixture does not exceed 3 - 5 kg, you can fix the bar directly to the GVL sheet. For this, special dowels for drywall are used - “butterflies” or snails.

Dowels "butterfly" and "snail" for fixing parts on drywall

The first are held as a result of the spread plastic construction under a sheet of drywall when screwing in a self-tapping screw. The second principle of operation is different - a very high and sharp thread with a large plane of contact with the sheet material creates a reliable connection when screwing in. The "snail" is screwed in completely, flush with the GVL surface, in the right place, and a hole remains in its center, into which an ordinary self-tapping screw easily enters.

- If the chandelier is heavier, then to fix the mounting plate, you will have to resort to the method with anchors with studs. - as described above. The protruding threaded parts of two or more studs will become mounts for a slatted or cross-shaped console.

All further actions are no different from mounting a chandelier on a regular ceiling.

Video: fixing a chandelier to a plasterboard ceiling

Mounting a chandelier on a heavy ceiling

None practical advice on self-assembly chandeliers on a heavy ceiling will not be given - this should be done only by craftsmen and exclusively before hanging the ceiling canvas.

Read detailed information, about what is important to know in our new article.

To install the chandelier, a mounting platform is prepared in advance and suspended from the floor slab, the lower cut of which should fall on the planned height of the stretched canvas. Based on the location of this embedded platform, the craftsmen must cut and properly process the holes themselves, reinforcing their edges, through which the wires and fasteners will pass.

Attempts to cut holes on your own in order to hang the chandelier on an already installed stretch ceiling, using methods of working like a plasterboard ceiling, will not lead to anything good. With a probability close to 100%, they are doomed to failure. A deplorable, but logical result of such amateur activity will be the need complete replacement canvases.

After the “ceiling” masters finish their work, leaving the necessary holes reinforced with special eyelets for the chandelier and fasteners, the installation of the lamp is carried out with the utmost care so as not to break or puncture the surface in any case.

On a heavy ceiling, it is preferable to use a pendant one so that the lamps are not in close proximity to the canvas. In addition, ordinary incandescent lamps, " halogens" or fluorescent "housekeepers" are not suitable for these purposes - they will quickly spoil the decorative effect of the ceiling covering. Therefore, in order for the ceiling to retain its attractiveness for as long as possible, only LED models are needed.

Video: an example of mounting a chandelier on a heavy ceiling

How to hang a lamp correctly and with your own hands so that there is good lighting, which, in turn, will create coziness and comfort in your home?

If you follow the safety rules, you can independently, without calling an electrician, hang the lamp on the ceiling or on the wall.

To install a wall light, you will need the following:

• lamp;
• switch;
• piece of cable;
• pliers or pliers;
• drill or perforator;
• tester;
• dowels;
• screws;
• a hammer;
• screwdriver.

Before hanging the lamp on the wall, determine the place on the wall by marking with a pencil.

Important!

Before starting the installation of the lamp, turn off the power supply in the house. With a tester (voltage indicator), we check the bare ends of the wires to which the lamp is attached.

We drill marks on the wall with a drill or puncher.

Select with teaching materials on our website

After mounting the ceiling, the mounting of built-in appliances occurs as follows:

1. Make marks for points on the ceiling.
2. Drill drill on marks round holes. They should be slightly smaller than the decorative outer element of the luminaire.
3. Connect the lamp clips to the wires and turn on the light. It must burn.
4. After removing the spring latches, hang the ceiling lamp.

Important!

If you have a plasterboard ceiling, then make holes in advance, before puttying and finishing.

With a stretch ceiling, the algorithm is the same, only the holes are not made with a drill, but are cut with a knife in the inside of a special glued heat-resistant ring.

So, hanging a lamp on the ceiling is not difficult by yourself. But, if you are not confident in your abilities, call a professional. How much does it cost to hang a lamp on a wall or ceiling? The price is acceptable - from 300 to 1 thousand rubles.

The cost depends on the complete or partial installation of the lamp. Partial installation is only connecting the wires of the device to the network. Another cost depends on the type of ceiling and the lighting device itself.

Igor
How to hang a chandelier on a hook if the chandelier is with a strap?

During the replacement process, it may turn out: the old lamp hung on a hook, and the new one is attached to the bar. Such a lock is usually equipped modern designs. Hanging a chandelier in this case is more difficult, but it will receive an additional shoulder of strength.

Modern chandeliers are equipped with slats. Brackets are screwed to them, which hold the lighting structure. The screws move in special grooves. Before mounting on the ceiling, it is necessary to experimentally determine their best position, which will ensure an easy attachment of the luminaire bowl. Optimally located screws must be tightened with nuts and proceed to installation.

Advice. For installation, use ordinary self-tapping screws with dowels. Often there are no fasteners in the kit. Reinforce self-tapping screws with a small cap with washers.

For regular flat ceiling hanging a chandelier is easy:

Advice. It is difficult to hold the chandelier and connect the wires at the same time. Invite an assistant.

If a hook is built into the ceiling at the suspension point, which is located in a small recess, this can be turned to your advantage. With the help of a hook, you will be able to further strengthen the bar:

• wind a strong steel wire to the hook so that a pair of free ends extend to the sides;
• prepare the bar, mark the ceiling;
  thread the ends into the grooves for mounting on the rails;
• press the bar to the ceiling and tighten the wire in this position;
• fix the structure to the ceiling with dowels and self-tapping screws.

Advice. In this case, use self-tapping screws with a head that is smaller than the diameter of the hole. Put washers on them.

Hanging a chandelier with a bar in this way will not always work. The hook can interfere with or disrupt the decorative design. There are two ways out of this situation:

• bend it to the ceiling with a hammer;
• dismantle the hook completely.

Safety precautions during the installation of the chandelier

All work under the ceiling must be carried out on a stepladder or a well-secured ladder. FAQ occur when hanging a chandelier on plasterboard ceiling. But the material is strong enough to hold a standard size structure. In addition, it is convenient to screw fasteners into it even without a drill. A suitable hole can be made by hand conventional drill. The subsequent installation technique is the same as with the concrete ceiling.

Chandelier installation

Before starting the installation of the chandelier, turn off the power at the switchboard. It is desirable to have a portable indicator device. Before connecting the wire, check if there is voltage in it. It has a phase and zero. The first of them will be shown by the measuring device.

It is important to carefully check the connection. Incorrect switching is possible: the switch on the wall opens zero, and the phase is supplied to the chandelier in constant mode. Such a lamp is dangerous because it can shock. The new wiring has 3-4 multi-colored wires inside. Zero flows in blue, phase in brown and white.

Advice. If possible, also connect the ground. The corresponding core in the wire is yellow or green.

You can hang the chandelier securely with or without a hook. To do this, strictly observe the technology of work.

How to fix a chandelier to the ceiling: video

The company "Husband for an Hour" offers the installation of chandeliers and lamps, as well as ensure the reliability of use throughout the entire period. Our company informs that it also recommends a service for the collection, installation, connection of not only chandeliers, but also various electric lighting devices for residents of Moscow and the Moscow region.

The installation of chandeliers is milestone in housing arrangements. But in fact, not all residents think about this process when selecting and purchasing a chandelier. After making a successful purchase, it occurs to many that this purchase still needs to be installed. Despite the fact that many try to hang a chandelier and connect it on their own, they still turn to the services of professionals in the end.

You may wonder why it is necessary to turn to specialists. In order to hang a chandelier, it is important to have knowledge of what it consists of. And accordingly, having no work experience in this area, it is better to refuse self installation. The average person who does not understand this can install the sconce incorrectly, and this can cause not only the lamp to break, but also lead to injury.

Why choose the installation of chandeliers from the company "Husband for an Hour"

The employees of our company are professionals who perform installation, take into account the characteristics and specifics of the structure of various lighting devices.

• We elect suitable remedy installations

• We adhere to all safety rules

• We have all the necessary arsenal to strengthen lighting fixtures

• Customer comfort is our most important goal

We make concessions to our regular customers

How much does it cost to hang a chandelier?

Prices for installation installation and connection depend on the value of the device, the severity, the type of attachment and the height of the ceiling.

The average cost of installation is 700 rubles. But in the event that the sconce has a weight of no more than 2 kg, or if two professionals are needed to install this device, then the cost will vary from 1500 to 3500 rubles.

Price minimum order is 1200 rubles. Behind additional information you need to contact the manager by phone or order a call back.

Functions and types of chandeliers

The chandelier is a pendant lamp that is attached to the ceiling and forms light in the room. Such devices differ in the number of diodes, design, light source. Such sources can be incandescent, phosphorescent, halogen lamps and diodes. There are 2 types of chandeliers, differing in their installation method.

Pendant lights are attached to the ceiling with special fixtures. Note that this type of installation is suitable for those rooms that are equipped with high ceilings. This is due to the fact that such devices occupy a huge space, in contrast to ceiling chandeliers. Ceiling mounted directly under the ceiling, which gives them a height that has the shape of a disk.


As for the types of these devices, they can be made for different tastes: classic, “modern”, crystal chandeliers belong to an independent category. If the ceiling is suspended or suspended, this device is installed in it. We advise you to turn to the services of our company "Husband for an hour", which will help you hang a chandelier on the first try and without any problems. Experts are knowledgeable in such matters as connecting sconces the right way, use special mechanisms and have deep knowledge in the field of electrical engineering. "Husband for an hour" is a comfortable tool for finding specialists who provide their services for affordable prices. How to contact our specialists

A specialist who makes a home visit is able not only to carry out the installation of electrical appliances, but also to resolve the difficulties associated with household appliances. What service does our company provide:

• Installation of electric lighting devices
• installation of lighting fixtures in a false ceiling
• assembling a chandelier of any complexity
• installation of spotlights
• chandelier cartridge change

At the end of the service rendered, we guarantee that there will be no interruption in the use of equipment, so there will be no short circuit in the wiring. The price of the service also includes free consultation, which includes the rules for the use of lighting fixtures. What the experts offer

The specialist will offer the following services:

• Will test the reliability of fastening for a chandelier
• prepare wires (wiring, insulation)
• will determine where zero and phase
• correctly align the wires with the wiring
• check the insulation properly

The company offers services not only for installation of the device, but also for diagnostics. Service "Husband for an hour": the advantages of the Master will provide service for high level. Specialists will mount the device in a short time without damaging the device itself and the wires. It will not be difficult for specialists to install the device to switches with a different number of sections, and they will install the chandelier on a special bracket or mount. Advantages of cooperation with specialists from the company "Husband for an hour":

Specialists work around the clock and take orders at any time

The specialist uses only modernized equipment

Replacement old chandelier for a new device does not particularly depend on local conditions, such as, for example, in order to change the bath, it is necessary to carefully dismantle the sewer.

At the end of this article, you will have an average indicator of how much it costs to hang a chandelier in a given month in Moscow.


How to hang a chandelier:
Fasten a special ruler in such a way that it can penetrate into the device device, to the hearth of the eyeliner that equips the wires in the device with electricity. The ruler must be fixed in such a way that it can be easily pulled off by unscrewing the artificial head screws. After installing the ruler to the ceiling, attach the wires, attach the device case and tighten the screws.

The replacement price of a chandelier asks for adjustments of the average according to the following criteria:the position of wire production and the need for replacement or operation, or the need for a total change with wires that feed the switch the property of the new deviceability to be firmly fixed to the ceiling

Advantages:

• We act at any time;
• We will provide a guarantee for 90 days;
• Visit of a specialist within an hour;
• We operate not only in Moscow, but also in its regions;
• Practice in this field for over 10 years;

It will be important to specify the payment for changing the device.

We offer a full range of installation services. Our company will complete this order in a short time.

In order to hang a chandelier, you need to do the following steps:

• Turn off the electricity in the room
• If necessary, assemble the device and test the strengthening system
• Disassemble a used device
• Install the device
• Connect it to the mains;
• Check performance and functionality.

Everything seems extremely simple, but in fact it is better to resort to the service of a specialist who has not only necessary knowledge, experience, but also the appropriate tools. Using the services of an experienced electrician is easier and cheaper than repairing in further system power supply. What determines the price of this service.

The price for this service includes the call of an electrician. But in the end, other conditions also affect the price:

• Type of device, difficulty of assembly and installation
• Weight of the device requiring installation
• Means of fastening the device hook, chain, mounting plate etc.;
• chandelier switching device, type of switch.

Characteristic features of installation various kinds device If it is necessary to change the location of the device, you need to call an experienced electrician. Thus, only an experienced specialist will be able to figure out the fixing method, guarantee the installation and the correct supply of electricity.

A common method of installing the appliance with a bowl is a hook mount. The wiring attachment locations are usually hidden. But the peculiarity is the need to consider whether the hook can support the weight of the chandelier, or replace it with a more durable one.

The electrical appliance can be powered by a cross or standard lighting bar. When replacing this instrument, this part must be replaced first. If there is a control panel, this element is equipped with power after the wall switch has been disassembled.