How to properly connect the ceiling plinth. How to join a ceiling plinth in the corners. Proper trimming of the ceiling plinth - how to do it
It is no secret that the main function of the plinth, which is fixed at the junction of the ceiling and walls, is decorative. Despite this, both the fixation itself and the joining of the ceiling plinth in the corners is a rather difficult undertaking. The plinth strip must be cut into segments of a clearly defined length and carefully sawed down their ends at an acute angle, using a miter box or a fine-toothed hacksaw. Only after these procedures have been completed should the ceiling plinth be joined in the corners and around the perimeter of the room. In view of the specifics of such work, it is necessary to consider in more detail how to join the corners of the ceiling plinth correctly.
The use of a skirting board for a ceiling: technical features
As you know, the direct purpose of the plinth is to hide the junction of the ceiling with the walls. If we are talking about a stretch ceiling, then here you need to hide the gap between the stretch surface itself and the walls. Besides, ceiling plinth can also visually fix the problem uneven corners in room.
The production of a ceiling plinth is most often carried out from materials such as polyurethane and foam, therefore, as a result, these elements do not have much weight at all. But you can also find wooden or plaster cornices. The standard length of the skirting board is 2 meters. The surface structure can be either embossed or even. Most popular color skirting boards - white, but if desired, you can always purchase plastic plinth almost any shade.
Skirting board for the ceiling is perfectly combined with, for example, plastic tiles, panels and wallpaper. Often, the installation of the plinth is accompanied by the installation of elements of gypsum stucco, which gives the interior even more harmony and a finished look.
How to join the plinth on the ceiling?
It is important to remember that the installation of the cornice is best done before finishing the ceiling and walls, that is, before painting and pasting the wall with wallpaper. Particular difficulties may arise with how to join the corners of the ceiling plinth and its elements around the entire perimeter of the ceiling.
The length and width of the plinth strips may vary depending on who is the manufacturer of this finishing material. The width of the plinth should be determined, as a rule, by the size of the room being equipped. As for the length of the bar, it can have indicators ranging from one to several meters. The material itself, from which the skirting boards are made, whether it be wood, gypsum, polystyrene, etc., does not affect the process of joining the cornices in any way (more details: "").
Undoubtedly, modern market building materials also offers such samples of skirting boards, which are already completely ready for docking in the corners of the room. When mounting such material, the connecting sections will have to be straight, not oblique. Of course, the cost of such cornices is higher compared to standard skirting boards.
The mounting surface must be properly prepared. It must first be cleaned of dust and dirt and allowed to dry. Before joining the planks, you need to level the attachment point, and also treat it with putty and a primer. When installing the skirting board on plaster, it is recommended to pre-treat the surface with water-based paint.
Not knowing how to join the ceiling plinths in the corners, if the corners themselves are uneven, you should remember that such a device is quite possible to implement, it is only important to clearly follow all the installation instructions (for more details, see the article: ""). It is necessary to start mounting the plinth from the corner of the room near the entrance to it. To properly cut the material at an angle of 45 degrees, it is best to use a device such as a miter box. This tool has the appearance of a box, which is equipped with slots at a variety of angles.
Elements necessary for joining the plinth
It is much more difficult to join the skirting boards in the corners of the room than along the perimeter.
To do this job well, you will need the following set of tools:
- hacksaw or clerical knife;
- goniometer;
- miter box;
- pencil;
- ruler.
Thus, tools such as a miter box and a hacksaw are a kind of economical devices, since when working with them, the percentage of waste due to poor-quality work is extremely low. Moreover, the material is not subjected to excessive loads, as, for example, when using a standard saw, so the risk of its deformation is much less.
But it often happens that there is no possibility to use the miter box, and the corners of the room are far from perfectly straight. All installation will have to be done by hand. To do this, you need to make a special stencil from cardboard or thick paper that repeats the shapes of the inner and outer corners.
In the event that polystyrene acts as the material for the plinth, then it is not necessary to use such a difficult tool as a miter box at all, it will be enough to get by with an ordinary construction knife with a sharply sharpened blade.
Corner connection of the skirting board for the ceiling
You can connect the ceiling plinth in the corners of the room by arranging two types of corners - internal and external. The indicator of internal angles that are in any room is always less than 180 degrees (usually 90). External angles are much less common, and their value is already more than 180 degrees (usually 270). The basis of each of the corner joints is made up of two plinth strips - right and left (more details: ""). Trimming of these strips must be carried out based on which of the corners of the cornice is planned to be equipped.
Working with inside corners
Initially, you need to measure the angle between the siennas of the room. If it is straight, that is, equal to 90 degrees, then the ends of the plinth should be cut at an angle of 45 degrees.
The strip is cut as follows:
- The plinth is installed in the miter box.
- The edge of the bar is pressed against the groove marked 45 degrees.
- Using a knife, part of the element is cut off from the canvas.
Arrangement of external corners for a ceiling plinth
Cutting the outer corner for the skirting board to the ceiling usually does not cause any particular problems, despite the fact that such an angle is much less common than the inner one. His device follows the same principle exactly the opposite.
It is important to remember that even before marking, the cornice must be completely ready for installation. This means that the inner corner must already be cut off or ready to be joined. The plinth needs to be laid in a miter box and pressed.
In the event that the longer element of the plinth is located on the left side, then it must be cut along the left mark of 45 degrees in the same way as the inner corner. Next, cut off the right corner in the same way. Do not forget about the need to check the quality of the joining of skirting boards in the corner even before their final gluing.
Installation of non-standard corners
It also happens that the room can be equipped not with standard corners of the usual shape, but with unusual corner structures, for example, rounded ones. If plinth trimming of ordinary corners is carried out according to standard scheme, then the arrangement of rounded corners with a plinth should be approached slightly differently.
In this case, how to cut off the ceiling plinth is affected, first of all, by the curvature of the mounted corner. The bar needs to be cut into separate elements, for example, 5 centimeters each. To stick the skirting exactly in the corner, you will need about five such segments. After completing the installation of the rounded part, it is necessary to get rid of excess putty with a spatula, and then stick the ceiling plinth according to the standard scheme on a flat surface.
How to join a ceiling plinth, details on the video:
So, after completing all of the above steps strictly according to the instructions, the ceiling plinth will turn out to be neat and reliable, and the device process itself will not become something extremely complicated. In order to perform the entire installation with the highest quality, if you have any questions regarding the installation of a skirting board on the ceiling and in the corners of the room, it is recommended, as necessary, to seek help from interior finishing specialists, who can often provide photos of options for installed skirting boards and detailed videos on their installation.
Ceiling skirting joint
When repairing premises, decorative elements such as ceiling plinths made of different polymers are often used. They are also called fillets, friezes or baguettes. They not only decorate the ceiling, but also complete the repair. However, their installation does not represent special difficulties. But how to join ceiling plinths between themselves and in the corners so that they look neat and aesthetically pleasing?
Let's take a closer look at this point.
Choosing a plinth
A wide variety of finishing materials on the market sometimes confuses the consumer. Which baguette is better and why? How to choose the one that will be easy to install and look great? To understand this, let's look at the properties of the ceiling fillets offered by modern manufacturers.
There are several types of such decorative elements on sale, differing in the material of manufacture:
- wooden
- gypsum
- polyurethane
- polystyrene foam
Important! When purchasing material, buy an additional pair of fillets - in case of incorrect cuts in corners or other errors.
What is the difference between the elements different materials?
Wooden skirting boards
Wooden friezes are rarely used nowadays, as they must be combined with the rest of the finish. This implies that the room will also have wood wall panels and a wooden floor.
But not everyone likes it. And the cost of such products, performed, as a rule, manually, will be quite high.
Gypsum skirting board
Gypsum skirting boards are also rarely used because of their disadvantages:
- they have a lot of weight
- they are difficult to install
- their price is much higher than that of products made of polymers
Therefore, for economical repairs, fillets made of polyurethane or foam are left to choose from.
Foam elements
How to stick ceiling moldings
Polyfoam - the lightest and most cheap material. But it has significant drawbacks:
- low mechanical strength - therefore, even with a slight pressure on the skirting boards, dents remain
- not every type of glue or paint can be used for foam, so the sticker of ceiling plinths from it requires careful selection of paints and varnishes
- weak bending ability - which means that such a fillet can easily break
So that the best choice there will be polyurethane skirting boards.
Polyurethane fillets
They differ high strength, durability and excellent flexibility.
When choosing such decorative elements, you should pay attention to their appearance- they should not have dents, scratches, various stains and scuffs.
Usually these are products of pure white color, but they can also be colored. If you need painted skirting boards, then you should take a piece of wallpaper that is planned for decoration with you to the store and choose the necessary color for the fillets.
Before starting work on the sticker, the ceiling skirting boards must adapt to the ambient temperature environment within 24 hours.
Cutting ceiling fillets
Cutting a ceiling plinth
These products go on sale, as a rule, in the same size in length - 2 meters. Therefore, before proceeding with the sticker, it is necessary to calculate how many pieces will be needed for all the walls. And also evaluate how they will be combined with each other in the pattern and in the corners. In addition, you need to prepare the corner fragments in advance, namely, to cut the corners, which is the most difficult thing.
Important! You can mount the ceiling plinth both after wallpapering and finishing the ceiling, and before carrying out these works.
Our apartments and houses are built in such a way that one can only dream of geometric accuracy. This is especially evident when you have to stick wallpaper or decorative elements such as ceiling fillets. Therefore, before connecting the ceiling plinth in the corners, you need to use a goniometer and determine its size.
Indoor corners are:
- internal
- outdoor
And if the external ones may be absent altogether, then the internal ones are always present.
To work, you will need the following tools:
- ruler
- goniometer
- stationery knife
- hacksaw with fine teeth
- pencil
- clean rag
- miter box
How to cut the material?
Miter box for trimming the ceiling plinth.
The miter box is a special device in the form of a rectangular box with slots located at different angles. With it, you can quickly and very accurately cut the desired angle on the baseboard.
A hacksaw will provide even cut on polyurethane parts, without fringe on the ends of the plinth. If such a fringe does appear, the cuts are cleaned with a sharp clerical knife. You also need to trim the factory ends, since they initially have a slightly rounded shape, and the joints of such elements are subsequently clearly visible.
If the corners do not match those provided in the miter box, then it is easier to use the following method. Cut the first part at an angle of 45 degrees, and already adjust the second in place, gradually achieving a perfect joint.
You can do it differently. Put a piece of paper in the corner and knead with your fingers until it stops. The resulting fold will be the template for the cut line.
If a foam product is used, then it is not recommended to use a hacksaw - the joints of the ceiling plinths with this cutting method are ugly, since the foam is crumbling.
Well, in order not to suffer at all with cutting and fitting corners, it is easier to purchase ready-made corner elements in the store. They can also have a pattern in a style that matches overall design premises. This option will greatly reduce the time of work and save your nerves.
Ceiling skirting sticker
Ceiling board gluing
Ceiling decorative parts can be mounted before or after wallpapering. If the plinth is installed before the wallpaper, then, of course, its installation is faster and easier. At the same time, it is easier to close the cracks with putty and paint the elements if necessary.
But on the other hand, in this case, you will have to stick the wallpaper as carefully and accurately as possible in order to prevent the formation of gaps between the baseboard and the top of the wallpaper.
If it is decided to mount the fillets after wallpapering, then a break is needed for them to dry completely. In addition, when installing elements on finished walls, as well as when painting them, it will be necessary to protect the top of the wallpaper with masking tape from possible ingress of glue or paint.
For the installation of fillets you will need:
- acrylic based adhesive
- special gun for a cylinder with an adhesive composition
- putty knife
- acrylic putty
If not ready corner elements, then start gluing the skirting board from the corners. Otherwise, decorative corner inserts are fixed first.
The surfaces of the elements must be clean and free of dust.
Do not forget which side you are going to install the fillets to the ceiling and which side to the wall, as they may have different sizes shelves.
Important! If you need to hide electrical wires or other communications under the ceiling plinth, then they must first be attached to the wall so that they do not cut off your decor with their weight. On sale there are fillets specially designed for such purposes.
We glue the ceiling plinth
With an existing stretch ceiling, the ceiling plinth, if it is made of polyurethane, is glued only to the wall surface.
Glue is squeezed out of the cylinder inserted into the gun in a thin continuous line. It must be applied on both sides of the product or on the marked line on the ceiling and on the wall. It's more convenient for anyone. Before making the joint of the ceiling plinth, enough glue is applied to the ends so that when the products are combined with each other, it protrudes a little. The excess is removed with a wet sponge, without waiting for the composition to set.
It is undesirable to repeat the curvature of the walls with a plinth. It is better to let gaps remain under it, which can be hidden by subsequent puttying, rather than the unevenness of wall structures or the ceiling will be emphasized. Therefore, when installing the fillet in place, press it gently in a straight line, without pressing it into the walls.
After applying the glue, the plinth is applied to the surface after a few seconds, so that the glue has time to thicken a little.
Conclusion
Beautiful fillets, made in various patterns and styles, will give your home a respectable and luxurious look.
And sticking ceiling plinths is not difficult if you follow the recommendations for their installation. The main thing is to make cuts in the corners correctly. This will help such a device as a miter box, or ready-made decorative corners.
Ceiling plinth gives the interior a finished, neat look
One of important elements interior decoration rooms, this is a ceiling plinth. It would seem a small detail, but without it the room will have an unfinished look. Gluing straight elements is not difficult, difficulties may arise with fitting corners. Therefore, in order not to get into a dead end during installation, you need to know how to join the ceiling plinth - if you do it wrong, it will be quite difficult to hide defects.
Ceiling plinth, it is also called fillet - an integral part modern interiors. Their use allows you to hide imperfections at the junction of walls and ceilings and give the interior a finished look. Ceiling baguettes They are made from different materials, but the most popular are foam and polyurethane. Working with them is quite easy - they weigh little and are easy to cut.
The plinth is produced in strips up to 2 meters long, so during the installation process, joining of the strips will be inevitable. The most difficult joints are corners. They are of three types:
- Internal.
- Outdoor.
- Non-standard.
Skirting boards are attached before the walls and ceilings are finished, but the surface must be prepared, leveled and primed. If the walls do not differ in perfect evenness, it is better to take a narrower plinth - it will be much easier to join it. Respectively wide skirting boards best used on flat walls.
If the joining of the plinth was not without gaps - this often happens when fitting non-standard connections, they can be sealed with sealant. It is best to use acrylic - you can paint on it. After the gap is sealed, you need to form a joint. The sealant can be smeared with a finger, and the residue can be wiped off with a sponge.
Trimming the plinth depends on the type of corner: external or internal
Mounting sequence
The baguette must be glued in the following sequence:
- the ceiling plinth is attached first in the corners;
- then flat areas are glued.
It is necessary to join the fillets on flat areas. Therefore, installation begins from the corners. If you glue the plinth in series, it will be difficult to fit, because. on straight sections it is much easier to cut fillets along the right size. Joints are best placed in that part of the room where they will be less visible.
Sequence of work
First of all, you need to prepare all essential tool. However, it is not so much:
- construction knife or hacksaw;
- pencil, tape measure;
- miter box;
- goniometer;
- rubber spatula, sponge.
Before installing baguettes, you need to do two things:
- Check the angle - if it is 90 degrees, then you can use a miter box to fit, if not, you will have to cut the baseboards manually.
- Attach the bar to the ceiling and measure with a tape measure: how far does the plinth go to the ceiling.
This distance serves as a guide for the correct fit and installation of baguettes. Since installation starts from the corners, each bar must be set at this level. Otherwise, you can get a situation where the skirting boards will be glued at different heights in different corners.
It is necessary to use a level so that the corners are at the same height
Why You Shouldn't Buy Trimmed Items
Manufacturers of ceiling plinths decided to make life easier for finishers by releasing already trimmed elements. It would seem that on this question how to join the ceiling plinths in the corners can be closed - it is enough to purchase ready-made parts and glue them. Unfortunately, not everything is so simple.
Cons of ready-made corners:
- high price;
- most often, the corners in the rooms are not even, i.e. not 90 degrees, but more or less. Therefore, prefabricated connectors are not suitable.
You can purchase them only after checking all the corners in the room.
Why you need to glue fillets before wallpaper
This question is asked by many novice masters - after all, if you glue the fillets first, the wallpaper will be harder to customize. And if after - the uneven joint of the wallpaper with the ceiling will be closed with a plinth. You can glue in any sequence, each person decides for himself how it is more convenient for him. But there is a difference.
If you glue the plinth after wallpaper:
- all uneven seams between walls and ceilings will be closed;
- when changing the wallpaper, you will have to change the baguettes;
- a high probability of smearing the wallpaper with glue during the installation of skirting boards;
- during installation, gaps may form between the fillets and the walls, which must be sealed with putty. If you do this on finished walls, they can get dirty.
When installing the skirting board, glue may leak a little.
If you glue the plinth before the wallpaper:
- the wall can be dirty as much as you like - fine finish not yet;
- all cracks are sealed without problems;
It turns out that it is better to glue the fillets before finishing - this way it is much easier and faster to work.
Miter box use
The miter box is special tool used for trimming the corner elements of ceiling and floor plinths. It was made in the form of an inverted letter "P" with slots in the walls at different angles.
Using it is quite simple. It is important to remember the rule - that part of the plinth that is pressed against the sidewall of the miter box is glued to the wall. And the one that is attached to the bottom will stick to the ceiling. To make it clearer, you can imagine that the bottom of the instrument is the ceiling, and the walls of the room are its vertical parts.
The joint of the ceiling plinth is done in this way:
- the baguette bar is turned over and inserted into the miter box. The ceiling part is pressed to the bottom, the one that is glued to the wall - to the vertical part. The plinth is pressed against the near wall of the miter box;
- the cut is done carefully, without pressing - otherwise torn edges will turn out.
The difference in trimming external and internal ceiling corners, consists in the correct placement of the left and right bars:
- left inner and right outer corners are cut in the same position;
- accordingly, the right inner and left outer are also adjusted in the same way.
Therefore, the main thing when working with a miter box is not to confuse the left and right bars. To facilitate the work, and each time not to remember through which grooves to cut, you can make the appropriate signatures on it for each docking position. It will take a little time - but in the future it will become much easier to work.
It is good to trim the plinth with the help of a miter box
Trimming ceiling plinths without a miter box
In some situations, you have to join the ceiling plinth without a miter box. For example, if it is not at hand, or the walls are crooked. Therefore, it is desirable to know how to join the corners of the ceiling plinth using other tools.
There are several ways to manually dock:
- using a goniometer;
- making markings on the wall;
- drawing a miter box.
An important point - in addition to the fact that the planks need to be marked, when cutting, they must be kept in the same position as they will be on the wall. Otherwise, the cut will be crooked. Usually, a 90 degree template is made for this.
Making it is easy:
- screw an ordinary bar to any surface - it will serve as an emphasis for joined baguettes;
- if there is no bar, draw a straight line on the plane, and use a square as a limiter.
It is worth noting that the miter box does not always help. Therefore, you need to know how to join the plinth manually.
Docking with goniometer
In general, a protractor should be included in the arsenal of any finisher - in our apartments, the angles are rarely 90 degrees. When using this tool, joining the ceiling plinth consists of the following steps:
- the angle is measured with a goniometer;
- the resulting value is transferred to both strips of the ceiling plinth. It is important to align the planks in the same way as they will be glued to the wall;
- after marking the plinth, they are cut with a hacksaw or a knife, while there is no need to rush so as not to fill up the knife blade - then there will be gaps when joining.
If everything is done carefully, the corners will turn out beautiful.
Measure the angle conveniently with a goniometer
Marking on the wall
This method is useful when there is no goniometer. For marking, you only need a pencil.
Sequencing:
- bring one panel to the corner, draw a line with a pencil on the upper border of the plinth on the ceiling;
- make the same markup for the second plinth;
- the corner on the wall and the intersection of the lines on the ceiling are guidelines for cutting. To mark the cut line, you need to attach the plinth to the wall and connect the resulting points.
After that, the borders can be cut.
Draw a miter box
Another trimming option is according to the drawn markings. The markup is drawn according to the miter box principle - two parallel lines are drawn, and corners are marked between them. Also, you can transfer values \u200b\u200bfrom a protractor to such a markup - cutting baguettes will be clearer this way. In this case, you must not forget to put the plinth in the right position when cutting.
Of course, these methods, at first, will not give perfect result- the junction will have to be adjusted, but this is done very simply. But over time, the hand will fill up, and the cuts will become much smoother.
Joining outside corners
The docking of skirting boards in the outer corners is done in the same way as in the inner ones. If the angle is even, a miter box is used. If not, cut by hand.
Sequencing:
- on the ceiling, the distance of the skirting board for both planks is marked;
- the left and right baguettes are alternately applied, marks are made with a pencil along the upper edge of the plank opposite the corner;
- the intersection of the lines - the top point of the cut, the corner - the bottom;
- panels are applied and marked;
- baguettes are carefully cut, while they must be kept in the same position as they will be on the wall.
When joining ceiling plinths at external corners, one unpleasant feature may appear. When the baguettes are already fitted and glued, they begin to disperse. To fix them, it is good to use long needles from syringes. To do this, the fillets are connected at the top and bottom. When the glue dries, the needles must be removed - there will be small holes that are easy to repair.
Irregular corners
good option for semicircular corners is the use of polyurethane plinth
Sometimes you may encounter a situation where you have to glue fillets at non-standard angles. For example, how to dock a ceiling plinth if the corners are semicircular? This is done quite simply.
Since it will not work to give the desired shape to a whole baguette - it must be cut into pieces of 3-5 cm each. The size depends on the radius of the corner.
Docking flat areas
The final stage in the installation of ceiling moldings is gluing straight sections. Everything is much simpler here. Smooth planks are fastened end-to-end to each other from one corner to another.
Sometimes skirting boards have to be trimmed - the edge can be damaged or unevenly cut at the factory. To do this, it is most convenient to use a miter box. In order for the bar to stick well, you need to press it down and hold it with your hand for several minutes. It must be remembered that baguettes are quite delicate and it is easy to leave a dent on them.
Thus, making neat joints of ceiling plinths is a doable task. The main thing is not to rush and act carefully. This is where the old saying comes in handy - measure seven times, cut one. It is better to make sure once again that the markup is done correctly than to cut off the baguette again.
To decorate the ceiling surface with a stand, you need to connect the corners. For the qualitative implementation of this stage of work, it is necessary to have a complete tool for marking and cutting. When all technical aspects are taken into account, the fusion will be almost or completely invisible even with uneven corners with a large deviation.
Tools and materials
To join stitches you need:
- a pencil with a ruler;
- goniometer and dirt;
- electric puzzle, saw or knife.
The cutting tool is selected according to the material from which the edge is made.
If it's plastic, he makes a writing knife. A suitable wire is required for a wooden or metal product. Otherwise, it is impossible to make a high quality outer or inner corner.
The best tool for a perfectly smooth cut is an electric saw.
It is fully occupied by plastic, aluminum, wooden tiles. It's hard to get even cutting edges knife and wire.
Preparatory work
The place to place the base must be pre-aligned.
There should be no dust at the intersection between the wall and the ceiling. First, prepare the space for fastening ceiling tiles.
The corners in the room are not always the same. The deviation from the standard speed can reach 5 degrees. Therefore, it is only necessary to start cutting the grating plate after measuring the drive angle.
There are some important shades to consider in order to make high quality corner joints:
- Place the straps only after finishing the ceiling and finishing the walls.
- Cutting sheet metal without strong pressure.
If you apply too much pressure on the tool, the foam may fall apart and the hole may burst.
- Cutting to connect the elements of the outer corner is made from the inside of the rod and the inner corner from the outside.
- Use a chair - a tool that gives you a clear angle so you don't have to measure for a long time.
- Technological cuts on sprinkles to remove any defects.
Paste bonding ceiling panels only after preinstallation.
How is a ceiling blade cut?
The final design step for the ceiling surface is to be installed on the ceiling strip.
Depending on the configuration of the room, along with the internal corners, it is also necessary to make the exterior.
Procedure for cutting adjacent knitted boards
The containers are placed in the mud, and pressed from the side that is glued to the wall, and the one that is attached to the ceiling is mounted on the bottom of the tool. If the base is cut at a right angle, the cut forms an acute angle.
Set on the right side of the fillet, cut off from the left edge.
The base is placed in the mud and fixed, and then cut with sharp instruments. If it is wooden, use either a saw or wire. The plastic file is cut with an office knife. Using hand tool work your best so that torn edges don't appear.
The measures are repeated for the second line, and then the parts are installed at the installation site, checking if they fit close to the corners.
When there are gaps between the elements at the junction, the parts are recycled.
If cutting is done by hand?
Trimming is done by hand when there is no dirt, or it is not completely straight in the corner of the room. The latter is measured using a transducer. The resulting value is divided by two. The resulting value is the angle of intersection of the cross.
Using a pencil and a toothpick on the base, labels are used and then a cut pile or knife office is worked on these lines.
Finite elements are used at the corner to check accuracy. If there is a defect, cut it.
When cutting without residue?
Filte is quite difficult to combine without the use of tools, but it is possible:
- The rod is attached to the connection and then the place where the ceiling is held is removed with a pencil.
- Likewise, they come with another line that is planned to be connected to another.
- The intersection of two rows on the ceiling surface is transferred to both plates, and then the cut is removed from the edge to a given mark.
- When marking, they are cut with a knife or saws.
To test how hard it is to press down on the tool to get a good cut, you can first cut a small piece from the edge and then just around the mark.
If smooth edges still can't work, you can use decorative corners that cover all imperfections.
How to cut fillets for outer corners?
The procedure for cutting the edge of the ceiling for the outer corner is almost the same as the similar scheme for trimming the outer corners. The bar is installed on the ceiling surface, indicates the place where it will be cut.
The part is then placed in a chair with sharp corners.
When the fillet is located on the right side of the corner, cutting to the right is performed.
Details on how to trim the edges in the corner and connect it
Similar actions are repeated with another footer. Then place both parts in the place where the ceiling rails are to be installed.
How to properly attach a fillet in non-standard corners?
When the space configuration is different from the standard, which means that it has a rounded edge, it will take more force to connect than when installing the fillet in the standard form space.
In such situations, knitting of knitted fabrics is carried out either from pre-prepared polyurethane profiles, or from ordinary ones.
If you are using standard planks, cut them into pieces. In order for the work to be done efficiently, allow the angle of curvature. The fillet is usually cut into 5 or 6 pieces. detailed information refers to the area on which the bonding is bonded, repaired if the surfaces do not follow curves and do not fit closely.
Glued parts also require precise work with the kit.
The structure penetrates the void, making the joints invisible. When this part of the work is completed, proceed to install the fillets on flat parts.
Dock fillet on a flat surface
This last phase is passed when the outer and inner corners are completely closed.
How to properly glue ceiling panels?
Typically, the fillet is placed on liquid nails or glue, which are applied to the back. When the glue is applied, the part refers to the mounting location, but do not press. The pedestal is held with the edge of the palm.
Don't press too hard, especially if the file is made from a base.
Remove any exposed adhesives immediately with a paper towel or cloth. Otherwise, it will be difficult to remove it. To attach the fillets, the elements are secured with colored tape.
When the adhesive composition is completely dry, the strip is carefully and carefully removed and the strips are fused with the sealant matching the color of the files or putty. Installation completed. The only thing that may be required is to paint the surface of the base.
conclusion
In order to correctly connect the edges of the ceiling in the outer and inner corners, it is necessary to correctly use the mark and cut the fillets accurately.
If accuracy is not maintained, large gaps will form or belts will fit tightly together.
Details on how to trim the edges in the corner and connect it
The final level of space renovation is completed by installing sidewalks to the ceiling and floor. Here's the question: how to cut like a ceiling.
The same problem arises in the formation of the earth. Therefore, in this article we will tell you how to properly cut the pedestal in the corners.
Knowing the main product of mystery and nuance, it can be installed quickly and efficiently, the space will be attached to the filled form, which will create a harmonious environment for the cut surfaces.
Catch cutting characteristics of ceiling edges
At first glance, installing the package on the ceiling is very simple - most of them are attached to the adhesive.
The most important of them are preparatory work: cutting strips and corner pieces for ceiling gaskets.
The room was beautifully decorated and didn't need any refurbishment, you need to know how to make corner baguettes.
By mastering the knowledge of how to cut the corner of ceiling rails, you will not only save Construction Materials and install temporary objects, but also resources that you could spend on a good wizard.
Design and cutting of the inner corner of the ceiling bag
When cutting surfaces, the question arises: how to join the corners of ceiling surfaces.
They may be:
Connecting ceiling fillets - external and internal (external) corner
We analyze in detail how we can cut the corners of the ceiling surfaces.
A typical rectangular space without ledges or columns has 4 corners where inner join disks.
Therefore, before applying the markings are marked, during which it is necessary to measure the circumference of the ceiling, mark the points of the connecting and connecting parts.
There are places for cutting on baguettes
How to make sheet metal to form an inside corner?
First check the angle between the ceiling and the wall. If the surfaces are smooth, they should be at 90 degrees. In this case, the curved elements are cut at an angle of 45 degrees. cutting knife can be used for cutting (foam injection, polyurethane, metal saw, but it is best to use a special carpentry tool- countertops (slit with grooves) and grinding.
Baguette cutting machine, photo
Advice. Before cutting ceiling walls.
check if the tool blade is sharp - dull knives leave jagged edges. A wide bag should be kept on the other side.
Then the first sheet is inserted into the chair evenly, fixed and cut on the right side at a 45 degree angle.
Cutting edges at an angle
Before gluing the baguettes, the other corner piece is cut so that it is cut from the opposite side.
Details are checked, check the tightness of the connection
After cutting all the details, you can proceed with the installation of the ceiling on the ceiling.
Recommendation: if the angle between the ceiling and the wall is uneven, the file is applied to the wall, this is done by counting their placement and crossing at the corner, and then manually with a knife made from the fit (while the joints need to be adjusted).
Cutting and joining ceiling sheets at external corners
If the space has complex ceiling or projection walls, outside corners form.
How to cut off the ceiling in this case? A chair is also used for these purposes.
How to cut correctly ceiling coverings to form an outside corner? First, the fillet is inserted into the tool for the side closest to you. The edge next to the ceiling should be at the base of the dirt.
In addition, cutting at an angle of 45 degrees.
Important: carefully store the baguette, otherwise, with uneven cutting, a gap will appear during the connection process, which is difficult to restore.
Diagram - how to cut like a ceiling to form an outside corner
Before placing the corner of the ceiling edges, you need to reduce the number of bags and check the smoothness of their connection.
The two cut pieces are put together. If there is no gap and edges of products that fit snugly, cutting is performed correctly.
An example of how to correctly combine the numbering details in the corner
tips
If you don't have a special baguette cutting machine, you can use a square or make a cardboard sample.
Any unevenness can be carefully cut with an office knife and if there are small cuts, they should be filled with sealing material.
Many people are concerned about the question: how to connect the footer if the walls are uneven?
In this case, the first fillet can be scored in the chair and the other hand adjusted manually until the cuts match.
Important: in this case, all spikes are made inside the fillet.
Via plastic corners joints can be carefully formed
Characteristics of working with various materials
If you install file from plaster ceilings generally do not cut.
They should be cut off from the decorative side. In this case, the chips remain on the underside of the product. If burlap is attached to the back of the plaster, it must be cut with a sharp knife. Then a special saw cuts the slices at an angle of 45 degrees, forming the outer and inner corners.
Advice. In order not to break the fragile gypsum product, you must first screw holes in the screws and start repairing them.
Installation of a plaster bag, connection of two edged parts
How to cover joints between fillets?
The sealing of the joints is done with plaster or putty, and after the drying process, the rough surface is rough.
Full presentation of how to cut a ceiling pedestal - video:
Characteristics of the occurrence of catches of floor coverings
The floor side panel not only covers the final look, but also hides the deck along the walls of the wall, improves the soundproofing in the room.
How correctly and exactly you can join the arches in the corners will depend on the perception of the space as a whole.
How to cut a section in a corner? Required tool:
- tape and pencil;
- chair;
- saw or sawdust for cutting the product;
- abrasive paper;
- print or putty.
Step-by-step instructions for forming the corners and joints of the ground
First, the marking and calculation of the required edge material must be done.
To get a clean corner, the cut pieces must be cut at a 45 degree angle. To do this, the part is installed in the mud, attached and cut off on one side with a saw or saw blade.
Similarly, you should see the opposite end of the second line
Advice. It's best to practice small pieces first, so you draw conclusions for your own purposes.
To connect the surfaces along the perimeter of the wall, they are cut at an angle of 90 degrees.
The edged edges of polyurethane products are processed with scissors to improve them and better grip.
Connecting two rods at a right angle
Before installing the sheet, first check that the connection is correct.
Then attach the first piece, complete with the other, cut at a 90 degree angle.
Advice. It is recommended to use polyurethane and plastic strips co special glue, and if your floor is decorated with wood paneling. then the joints of their joints are attached with glue and further reinforced with nails.
A special PVC connector is used to hide the connections.
During installation, you can cut a piece of ribs to make a connection in it.
There may be connectors for connectors, switches.
PVC socket
The corners, internal and external, are designed in the same way as when installing ceiling bags.
Cutting a baguette is done in a similar way.
Special corners are available to close the joints of polished PVC products
tips
In order to quickly and efficiently cut and install packages, you must plan all the work in advance and prepare necessary materials and tools.
After the measurements have been taken, note the length of each wall, adding 50mm to each side (for the edge of the edge of the edge).
Try to cut the planks so that the leftovers are as small as possible. To save the material, cut it back and forth.
How to cut bags easily
To securely attach the workpiece for further cutting, you can use crochet. This is a special wedge clip and a grooved stick is attached to the back.
How to Join Ceilings in Corners - Installation Features
This groove is made at an angle of 45 degrees. Therefore, it can be used as a deep base cutting template.
To do this, take a thicker stick.
To accurately cut gratings, use a special cutting saw. Using this, cut the grooves in the template to the desired angle.
Result.
Beautiful ceiling and floor coverings are added to the interior of the room.
They not only decorate the room, but also protect the surface from damage. The stand can be made independently (wooden) or bought finished goods. To make this frame look nice, the edge details need to be trimmed properly during installation. Following simple guidelines, you can mow the bags yourself and shape the corners.
He will also talk about them.
Tools and materials
The ceiling (file) of the ceiling is made of different materials. Expanded polystyrene and PVC stand out from budget products. Both versions are crushed during cutting, the surface can be deformed, so you must work with them carefully. A denser structure is extruded polystyrene and polyurethane. But I personally prefer wood more. Eco-friendly, striking appearance combined with beautiful carving ornament will match any room decor.
In other cases, you need to cut the tool with a sharp blade.
Depending on the material from which the ceiling is made, there is also a certain degree of difficulty in trimming the edges of the ceiling in the corners.
From handy tools, which I used:
- roulettes;
- pencil;
- saw;
- chair.
Before that, I had to cut pieces of polystyrene in the decor of the wall without dirt.
I had to take myself, but in principle everything was done. Now I can evaluate the instrument. I will say without exaggeration, it really helps to make the cut smoother and more accurate.
I didn't use a saw blade to use the saw that comes with the kit and cut the saw with fine teeth, but if the goods are in order, it can be controlled and usually with a knife.
Ceiling Corner Trimming Instructions
Before I came to work, I set the parameters for each corner.
You rarely find flat surfaces in homes and old building homes. If they are aligned to the end of the wall and ceiling, then angular velocity is 45°. I also recommend that you follow this sequence:
Apply the base to the place of gluing, place the mark in the pencil;
At the bottom of the tray tray, place the fillet with the wrong side down (on which the glue is applied) and squeeze the bottom against the wall of the tool;
Step 3. Without excessive pressing with a sharp knife or wire, make a cut, observe the desired angle;
Step 4. The adjacent file is also cut on the other side of the chair;
STEP 5. Then use the tin on the ceiling to install.
If necessary, you can cut the cuts with a sharp knife. Small gaps that are just covered by the whale.
There are several marks in the dirt that determine the type of corner (external or internal).
The cutting principle does not change, only using control connectors from different sides. But it is difficult to install fillets on both sides.
It is important that the pre-designated length is maintained. Otherwise, there will be a break in connection with one of the elements.
If there is a relief pattern on the fillet, we take into account the integrity of the artistic end of the end.
How to join ceiling surfaces in the corners - no worse than a master!
Before trimming, you must test both elements to create a consistent transition based on the sketch.
1. To understand how to cover the edges of the ceiling in the corners, you can pre-work on small pieces. After trying to work with dirt and tuning mode without it, you still need to select correct option for yourself.
If it is not possible to use a table, you can draw it on thick cardboard or a wooden board. There is also a cutting method that involves applying directly to the wall.
Do not cut the cut with abrasive paper, even if it is made of fine abrasive. This method is only suitable for wooden cardboard, plastic foam just decomposes.
4. For preliminary measurement of the angle on the wall, attention should be paid to the degree of deviation of 90 °.
If the irregularities are obvious, and the edge is narrow, it is better to fix the corners of the wall with whales.
5. Do not install a wide surface in a room with a low ceiling.
They will hide the space even more.
6. It is very easy to build a chair alone with plywood and cardboard.
With reverse side you should note the markings on the paper that define 90° and 45° in two directions.
Finally, I would like to add that the work will facilitate prior knowledge of the properties of the material from which the file is made. This will allow you to choose the right cutting tool and improve cutting.
How to dock a ceiling plinth: trimming with a miter box and a manual method, docking in straight sections
Perfectly matched ceiling plinth
Since the installation of the ceiling plinth is always made from standard strips 2 m long, in the process of work it will simply not be possible to do without joining them.
How to join the corners of the ceiling plinth
At the same time, it does not matter what material the fillets are made of - gypsum, wood, polystyrene or other polymer material(See Ceiling Skirting for plastic panels: mounting technology).
High-quality docking of skirting boards is feasible, even if the corners in the room are uneven (with deviations of 90 degrees), the main thing is that the tool necessary for marking and cutting is available.
So, let's look at how to make the joints of the ceiling plinths on flat areas and in the corners as invisible as possible.
Docking plinth in the corners of the room
Since it is the most difficult to qualitatively arrange the corner joint of the ceiling cornice, we will first figure out how to properly dock the corners of the ceiling plinth.
To do this, you need to prepare the following set of tools:
- Stationery knife or hacksaw (with a fine tooth).
- Miter box.
- Ruler.
- Goniometer.
- Pencil.
Trimming the ceiling plinth with a miter box
Tool for trimming ceiling moldings for joining in corners
It must be stated right away that modern realities in our country, the miter box is far from always a life-saving tool for precise corner trimming of the plinth.
The fact is that the angles in our houses are often not equal to 90 degrees, but arranged with an error of up to 5 degrees.
The miter box is designed specifically for trimming the plinth at even angles (see the final lesson of the ceiling alphabet: installing ceiling plinths). For this reason, when repairing high class, you will first need to correctly measure the angles with a goniometer and, depending on the result, use or not use a miter box.
Let's assume that the corners are still even, and a miter box can be used to trim the plinth.
In this case, the preparation of skirting boards will have the following features:
- Corner joining of the ceiling plinth can be formed by two types of corners - external and internal corners between adjacent walls.
There are internal angles in any room, and their value is always less than 180 degrees (usually 90). External corners are somewhat less common. Their value is always greater than 180 degrees (usually 270).
- In addition, each corner joint consists of two plinth strips - left and right. Depending on which corner of the ceiling cornice (external or internal) will be equipped, the left and right skirting boards will be cut in a certain way.
Scheme for trimming ceiling plinths in a miter box for arranging external and internal corners
- To join the plinth at the inner corner, the left and right planks in the miter box are cut as follows:
- The left bar is positioned in the miter box at the farthest wall from itself with such a slope, which is assumed during the final installation under the ceiling.
The hacksaw is inserted into the left near and right far grooves of the miter box, after which an incision is made.
- The right bar is also installed at the far side of the miter box with a similar slope and a cut is made using the right near groove and the left far one to insert the hacksaw blade.
- For joining at the outer corner, the left bar is cut similarly to the right one for the inner corner, and the right one is cut similarly to the left one for the inner corner.
Before joining the ceiling plinth and gluing it permanently, it is necessary to try on the planks in the corner and make sure that they form a clear joint without gaps.
Manual trimming of the plinth for joining
Cutting ceiling plinths manually for corner joining is done with a clerical knife at an angle of 45 degrees
In order to more clearly understand the question of how to properly join the ceiling plinth, it is necessary to understand the features hand pruning ceiling plinth without miter box.
This cutting method is used if the angle is not straight or if the miter box is not accessible for any reason during installation. The procedure is carried out as follows:
- With the help of a goniometer, the value of the angle being equipped with the plinth is measured, and the result obtained is divided in half.
- Alternately, markings are applied to the left and right planks of the plinth in accordance with the final value (usually the value for conditionally right angles is close to 45 degrees).
When drawing a cut line on the plinth, it must be inclined in the same way as at the place of further installation.
- Along the marking line, cut with a clerical knife and try on the planks in the corner.
If everything is done as a rule, there will be no gap between the planks, and the angle will be even and clear.
Docking the skirting board for the ceiling on straight sections
How to dock the corners of the ceiling plinth correctly, we figured out, now we will determine how docking is performed on straight sections (see.
Plastic ceiling plinth: first acquaintance). And it is quite simple to do:
- When the corners of the ceiling cornice are installed (glued), the planks with straight ends are butted against one of the corner planks and attached.
Before joining the ceiling plinth in a straight section, the edges of the plinth strips must be properly sanded
- The next bar is joined to the previous one in the same way.
When the straight bar reaches the corner bar of the far corner on the same wall, it is tried on in length at the installation site and a mark is made to make the cut. Next, along the mark, the plinth is carefully cut off at a right angle.
Advice! In order for the ceiling plinth strips to form a perfect joint, the cut edges should be carefully sanded with fine-grained sandpaper.
In our article, we found out how to dock a ceiling plinth in the corner of a room and on straight sections, described the rules for using a miter box for trimming a plinth.
Now you just need to arm yourself the right tool, purchase, in fact, a plinth and boldly proceed to self-fulfillment works. And for those who have not fully figured out the intricacies of docking, we recommend that you find thematic on the network for a more visual representation.
What are the floor plinths and with what tool they are installed, the rules for the formation of neat internal, external and non-standard corners.
The content of the article:
Docking floor plinth in the corners - this is a responsible process, which is important to carry out with high quality, since precisely drawn clear corners are pleasing to the eye and give the flooring a complete look. To connect the products and get a neat joint, you need to know the technology of their trimming and existing methods fixation. Before cutting the floor plinth, read the instructions and recommendations below.
The main types of floor plinths
To date, skirting boards from the following materials are used for interior decoration - wood, plastic, MDF.
Plinth made of wood is a traditional type of finishing product. In old houses, only such ones were laid on the floor. Wooden plinths have a relief surface on the outside and special grooves for mounting wires and cables inside them. They are fixed with self-tapping screws, less often with nails. It is allowed to use sealant to fix them on the floor. If self-tapping screws are used for fixing, then dowels are pre-installed in the walls.
Among the advantages of wooden skirting boards, it should be noted durability, environmental friendliness, safety for humans and animals, the possibility reuse.
However, their use does not always allow you to hide the wiring. In addition, after installing a wooden plinth, it must be additionally puttied and coated with varnish, paint, stain. In addition, wood is an expensive material, and therefore products made from it will be of high cost. And before cutting the skirting boards on the floor, you will need to prepare special equipment.
Plastic skirting boards are simple and convenient products for finishing flooring. In them, everything is most often thought out to the smallest detail: the design of external and internal corners, pockets for laying cables and wires, end caps, special fasteners for fixing on the wall and floor.
Plastic plinths are distinguished by quick installation, variety color solutions, no need for puttying and painting after installation, the presence additional elements for sealing joints. This finish goes well with any floor material: parquet, carpet, tile, laminate, linoleum. Whatever coating you have, you can easily pick up a plastic skirting board for it.
However, plastic is a brittle material, and with a strong impact, chips and holes can appear on its surface. This will require complete replacement a whole whip of the product, at least. Despite this drawback, modern builders prefer plastic plinth because of the large number of its advantages.
MDF skirting boards are eco-friendly and attractive products. On them front side paper impregnated with dyes is glued. Moreover, the process is carried out at high temperature and under pressure. This eliminates the peeling of the decorative coating during operation.
A melamine coating is applied on top of the paper. It protects the skirting board from moisture and stubborn dirt. Even when hit by direct sun rays the product will not lose its appearance for many years. Also, the advantages of MDF skirting boards include quick installation, easy care, economy, wide palette of shades.
Before joining the floor plinth in the corners, it should be remembered that MDF is characterized by increased fragility. In the process of installation and cutting of such a product, extreme accuracy is important.
Plastic or MDF, from which skirting boards are made, are lightweight materials that have a large number of color solutions. That is why the product is quite easy to choose for any interior decoration and design solution. Most often, when choosing the color of the plinth, they are repelled by the shade of the floor covering.
Skirting installation tools
The procedure for cutting and joining skirting boards from different materials is not much different. The main difference is that wood, plastic and MDF have different hardness and density, and working with wood, for example, is more difficult. If a sharp knife is also suitable for cutting plastic, then a hacksaw is needed for wood.
To work with a wooden, plastic plinth or MDF, you will need:
- A miter box is a special carpentry tray for sawing, on the sides of which there are slots at different angles.
- Roulette and pencil.
- Hacksaw, jigsaw or carpenter's knife. Any of the above tools will work for cutting. But it's up to you to decide how to cut the plastic plinth for the floor. It depends on which tool is easier for you to work with.
- Fine-grained sandpaper.
- Sealant or putty.
- Fasteners (self-tapping screws, dowel-nails).
- Screwdriver and hammer.
How to cut the corners of a floor skirting board
The purchased plinth must be cut according to the perimeter of the room. To make this process faster and easier, you can draw a diagram of it on a piece of paper, marking all the outer and inner corners.
Cutting plinth to fit inside corners
Despite the fact that the rooms most often look like a regular rectangle, the angles in them are not equal to 90 degrees. Such an angle is the dream of any builder and repairman. If you are still lucky and you have a classic correct angle, then to cut the plinth, you must do the following:
- We place a wooden or plastic sheet in a miter box;
- We find on the side panel a furrow and a mark of 45 degrees;
- Focusing on it, we begin to cut the plinth with a hacksaw;
- The resulting edge is cleaned with sandpaper.
If you are unlucky and your corners do not have 90 degrees, then you need to do the following steps:
- We make a small markup on the floor. For this, a pencil or washable marker is suitable. On one and the other side of the corner, it is necessary to draw the future border of the plinth. In the corner you will get a kind of rhombus. Its diagonal is the cutting line.
- Having attached the plinth to the resulting rhombus, we make a mark of its diagonal.
- We draw a straight line from the received mark to the corner of the plinth. This is your cut line. Focusing on it, a cut is made with a hacksaw.
- The resulting end is recommended to be processed with sandpaper.
At the end, it is necessary to insert a plug into the resulting joint to form a neat inner corner of the plinth for the floor. If this is a tree, then the joint should be treated with putty and prepared for further painting.
Forming outer corners on skirting boards
If you have classic outer corner at 90 degrees, then the process of its formation is the same as the internal one. When cutting, you need to remember which baseboard you have on which side. After receiving the joint, it is necessary to close the ends with a special plug. If small flaws occur during the cutting process, they can be easily corrected with mastic, and then closed with a plug.
If you have non-standard angles, then cutting the plinth comes down to the following steps:
- We apply the canvas to one wall.
- Using a pencil, mark its inner and outer boundaries.
- We do the same with the other plinth.
- As in the case of the inner corner, we get a rhombus, only located outside. Its diagonal will serve as the border of the cut.
- With the help of a saw and a miter box, we trim.
- We carefully clean the resulting ends and install the plinth.
- The final touch is the stubs in the corners.
Cutting skirting boards at non-standard angles
Modern design solutions in interior decoration often involve the use of original forms. In this case, it is quite difficult to install a floor plinth in non-standard corners. After all, they are often both internal and external at the same time. Sometimes the corners are completely rounded. That is why the docking methods described above are not suitable.
If you are dealing with a round corner, then you need to cut the baseboard into 4-5 pieces. Using plugs for connection, carefully lay out the entire corner in small parts. Do not forget to fix them with glue or putty. Thus, you will get a neat rounded corner.
If you have an inside-outside corner in the room, then you should take the following steps:
- On the one hand, we apply the plinth and draw its border on the floor.
- Now we apply the second half and make two marks: one - the intersection with the drawn border, the second - with the wall.
- We connect the obtained points and make a cut.
- The ends are carefully closed with plugs.
Installation instructions for plastic floor plinth
We start the installation from the middle of the wall. To do this, we cut the butt at an angle of 90 degrees and carefully grind it with sandpaper. This will allow you to get a better grip between the two parts.
If you have sockets below, then you should carefully cut a recess for them with a jigsaw. The resulting surface is carefully processed with sandpaper.
If you need to dock the plinth with the doorway trim, then you should calculate the length of the canvas so that between the end and door jamb could only accommodate a side plug.
How to cut the corners of the floor plinth - look at the video:
Before cutting the corners of the skirting board for the floor, you need to prepare the right tool, depending on what material you are using. The procedure for installing products and forming beautiful and neat corners is simple, but it requires care and patience. With a little practice, you can carry out these finishing works on your own quickly and without problems.
Ceiling plinths perfectly complement the finish, are a wonderful decorative element. Sometimes they also perform a practical function, for example, they close the gap that appears during installation. stretch ceiling. A baguette can mask electrical wiring or serve as a basis for placement spotlights. Working with fillets is not particularly difficult. Problems can only arise when you have to decide how to join the ceiling plinth in the corners in order to get a quality result.
Corner preparation
The work will require several tools, devices:
- Pencil
- Ruler
- Goniometer
- miter box
Experts consider a reciprocating or miter saw to be the best tools for cutting skirting boards, electric jigsaw. But if there were none at hand, you can use a construction, stationery knife or hacksaw. The choice of tool depends on the material from which the fillets are made.
Sawing or cutting off a baguette should be done carefully to avoid formation, bumps, burrs, and not to crumble the material.
Before cutting off the ceiling plinth, you will need to determine the angle. Ideally, the walls should meet at a 90° angle. However, such an indicator, unfortunately, is rare. The real value must be divided in half to determine at what angle the fillets will need to be cut.
A special device, which experts call a miter box, will help to make perfect cuts. If it is not there, you can build a case from the planks U-shaped or corner. A slot is made on the side at the desired angle, along which the blade will move.
You can use a stencil made of cardboard or thick paper, exactly following the contour of the corner.
Docking fillets in corners
In most cases, you have to decide how to dock the ceiling plinth during inside corners. But in non-standard layouts there are speeches. In such cases, the design of external corners is required. Ideally, their value should be 270 °. If the actual figure differs from the standard, you will have to take this into account when cutting fillets.
On the preparatory stage corners must be thoroughly cleaned of dust and dirt. Before gluing the skirting boards, the surface must dry well. If the walls are uneven, you must first perform puttying. After drying, it is covered with a primer. This will ensure good adhesion. In the absence of a primer, you can replace it with acrylic water-based paint. She will provide high-quality fastening plinth to the wall. 
Some consumers prefer to purchase ready-made corner fillets so as not to cut them. Such elements greatly simplify the process. But you need to take into account that these baguettes have a higher price than ordinary ones. In addition, they are only suitable if the corners in the room are straight. Otherwise, a high-quality result will not be achieved.
Video