Do-it-yourself ultrasonic humidifier. How to make a humidifier at home: from a bottle. Decorative humidifier

How to humidify a room without a humidifier? Our "Kulibins" from "homemade" solved this problem by several methods at once, without spending a lot of money. Several very simple and interesting ways we would like to offer you for review.

Increasing the level of humidity in a room without the use of climate technology is actually very possible, the main thing is to be smart.

Simple options for humidifying the air in your home

The easiest humidifier: hang on the battery wet towel. The battery heats the fabric and the moisture evaporates.

Advantages are obvious

It does not require electricity, and does not require anything at all, except for a piece of cloth or a towel.

The disadvantages are also huge.

humidifies the room directly near the place of evaporation of moisture, requires constant "recharging" and very little efficiency of this method.

Complicated option. A towel with one end should be lowered into a basin of water, and the other end should be hung on the battery. The water will soak the fabric and gradually evaporate on the battery.

Advantages are obvious

Automated humidifier that does not require investment.

Disadvantages of the method

The low efficiency of the method, although automation through a basin of water increases the level of humidity near the battery quite noticeably.

If such solutions seem to you not aesthetic and not effective, then you can always familiarize yourself with

This process is not the easiest and will require certain tools and supplies from you. parts. To make it you will need:

plastic rectangular container for storage food products with a lid, liters for 5-7.
Used CDs, the more the better.
Plastic. You can use any plastic trim, the same thickness. Each piece must measure at least 5 cm by 5 cm.
Two pieces of thin plastic tube. The diameter must be selected empirically.
Choose a gear from a children's toy empirically
Electric motor from an old tape recorder.
Fan

The main tool you will need is a glue gun.

A homemade humidifier-purifier is done like this:

Take CDs. The central hole of the disc is sealed on both sides with pieces of plastic using a glue gun. It is better to make them round and the same.
After that, make through holes in them for a thin plastic tube. The plastic tube should have a size slightly larger than the width of the container.
The next step will be to put all the disks as close to each other as possible and fix them glue gun. The resulting workpiece should resemble the inside of an air washer.
We make 1 hole in opposite sides of the container and insert the blank with disks across it. On one side, you need to glue the washer with a glue gun so that the workpiece does not pop out.
On the other hand, to the protruding end of the plastic tube, using a gun, we glue a large gear.
We fix the electric motor with a small gear so that it engages and can rotate the inside with CDs inside the container.
In the lid of the container we make a hole for the fan and several holes so that moist and purified air comes out of them.

It remains only to fill in the water, plug the device into the network and enjoy the fruits of your own labor.

Do-it-yourself ultrasonic humidifier

Do-it-yourself ultrasonic humidifier, its scheme is as follows. A piezoelectric emitter will be lowered into a container with water on a special float mechanism, which will produce “cold steam”. The fan will supply air inside, which will push the steam out of the tank.

As a container, it is best to take a plastic bottle.
Fan with power supply
Ultrasonic emitter. In Chinese online stores, it is called Mist Maker or fog maker, and costs about 4-5 USD.

We begin assembling an ultrasonic humidifier with our own hands.

Step 1. Cut a hole in the bottle for the fan

With the onset of cold weather, various heating devices begin to work in dwellings. In addition to comfort, they also create some problems - they dry the air in the room, which causes problems with well-being. To avoid this, the air in the room must be humidified. Stores are filled with various humidifiers, but they are often not affordable. Therefore, such a device can and should be designed by yourself. Learn how to make a humidifier at home.

Master class: humidifier from a plastic bottle

Homemade humidifiers can be the simplest, made from improvised means, and using more complex devices. The basic principle of the humidifier is the evaporation of water. The more efficiently the water evaporates, the more comfortable it will be to breathe in the room.

The devices use different ways water evaporation - this is cold steam, in which water is dispersed with the help of a sprayer and a fine mesh, and with the help of a heating element, when water evaporates into air under the influence of temperature, and with the help of ultrasound, which turns water into mist.

The most elementary room humidifier is a container of water standing near heating appliances, which may be several. The disadvantage of this method is very low efficiency, because the water from the tank evaporates very slowly, and no special result is felt.

More effective is a device that can be built from a conventional one and a half to two liter bottles of water, two segments dense material, gauze cut, adhesive tape. The design is attached to the outgoing battery central heating pipes. Assembly order: a rectangle 10-12 cm long and with a clearance of 5-7 cm is cut out on the side of the bottle. Next, you need to take two pieces of fabric of such a length that it is convenient to hang the bottle for them to the radiator pipe. For greater strength and reliability, pieces of fabric can be attached to the bottle with tape.

The next step is to fold a large piece of gauze with a length of not less than a meter to make a ribbon about 10 cm wide. One edge of this tape is lowered into the gap in the bottle, and the other is wrapped around the pipe in a spiral. Two tapes can be used to enhance evaporation. Water is poured into a hanging bottle, and the free humidifier works!

Photo of a simple way to humidify the air

To make a more modernized humidifier from a bottle, you will need computer cooler, scotch, plastic bottle large volume (from 5 l). The bottle needs to be cut off the top so that you can install the cooler. They fix it with adhesive tape or electrical tape, and for greater strength and reliability, it can be fixed on a sheet of thick paper. Water is poured into the bottle, the cooler is connected to the network, and the air humidifier works.

It is worth noting that all of the above methods of air humidification are not highly effective, but as an "ambulance" or for small spaces are quite suitable, because comfortable indoor air in winter is a component of good health. Knowing how to make a humidifier at home from a bottle, you can save on the purchase of expensive equipment and at the same time humidify the air well in own apartment with your own hands.

The ingenuity of craft lovers truly knows no bounds. For example, many people prefer to make various simple appliances for the home, while spending a minimum of money and effort. In this article we will tell you how to assemble a household air humidifier from improvised materials with your own hands and give detailed diagrams actions for each described method.

Before starting assembly homemade unit, we advise you to understand the algorithm of its work. As a rule, the humidifier functions according to the following principle: water is poured into the tank, and then it evaporates. Thanks to the formed steam, the air in the room becomes more humid. Some housewives apply this rule in everyday life: they pour water into the basin, lower a cloth or towel on top and in this way increase the humidity in the room. True, this method is not very effective, and it increases the level of humidity only in the immediate vicinity of the pelvis.

Of course, modern devices work much more complicated, and this should be taken into account before creating your own humidifier. Traditional Humidifiers air act on cold steam using the built-in fan and filter cartridges. Steam models reminiscent of how they work Electric kettle : their main mechanism is internal heating element, or heating element. And finally, ultrasonic devices are based on the operation of a piezoceramic membrane, using alternating current converting water into tiny particles water mist, which subsequently enters the room.

Based on this simple knowledge, you should imagine what kind of device you want to get. We will highlight some of the most popular and understandable ways to make both a humidifier and an air purifier.

Yes, that's right: the simplest humidifier can be built from an ordinary plastic bottle! Such a device gives cold evaporation effect.

We will need:

plastic bottle volume 10 l;
desktop computer cooler;
tape or duct tape.

Cut the neck of the bottle so that you can easily insert a computer cooler into the hole. Pour water into the existing tank.
Immerse the cooler in this hole and secure it with tape. You can also cut out fasteners from cardboard or a piece of thick paper. For the second option, it is enough to make a slot that is inferior in size to the cooler body itself and attach it to the bottle, additionally wrapping it with adhesive tape.
Turn on the cooler in the power supply. As a result, the air in the room will receive enhanced moisture.

From expanded clay and buckets

To develop this device, we need expanded clay. This material is able to absorb moisture well and, accordingly, release it.

Here is a list of items we will need:

4 waste baskets: 2 small and 2 larger;
a bucket with a volume of 10-12 liters;
aquarium pump;
computer cooler;
building hair dryer with a high heating temperature;
plastic straps.

Instructions for creating a humidifier look like this:

We attach two medium-sized wastebaskets to each other along the edges of the rims. This can be done using a household hair dryer or ordinary plastic ties. This is how the body of the future humidifier is formed.
We connect the baskets in the same way bigger size, having previously placed inside the case, folded from smaller baskets. It turns out double layer construction, according to the principle of operation, reminiscent of a thermos or a heater.
Cut off the bottom of the basket that is on top. In some cases, it is enough to simply make a hole large enough to fill expanded clay inside. Keep in mind that expanded clay should be so large that it cannot seep through the holes in the trash cans.
We place the aquarium pump at the bottom of a pre-prepared bucket. We direct the tubes from the pump to the very top makeshift corps from mesh baskets. As a "cover" of the structure, we install a plastic ring with holes. From here, moisture will flow down, passing through the expanded clay into the bucket.
Finally on top of it complex unit it remains to install a computer cooler. Its task is to direct air into expanded clay nets saturated with moisture.
The final stage is also related to the operation of the cooler: it will force moisture-saturated air through the holes in the wastebaskets.

As you can see from the instructions above, homemade humidifier air is a very real and feasible task.

From the fan

Is it possible and how to make a humidifier with your own hands, if you only have floor fan? Attach a thick, damp cloth (or even a small mat dampened with water) to the pipe. Hang this structure at a height greater than the height of the floor fan. It can be a floor lamp, a stable stick, etc. Install a fan directly behind the fabric structure and turn it on. This moisturizing technique isn't very effective, and you'll have to constantly make sure that the cloth or mat stays damp all the time.

Incidentally, the same principle applies to incubator humidifier made by hand. Amateur poultry farmers adapt a moistened cloth or large sponge and create an air flow that enhances evaporation. Sometimes quite effective method it turns out natural evaporation water from pre-prepared baths.

Antibacterial humidifier from a plastic container

If you set yourself the task of not only slightly moistening the air, but also holding it basic cleaning We recommend using this method.

To make the device you will need:

Plastic container;
fan with low level revolutions;
filter with disinfectant (antibacterial) properties.

Note that an ordinary moisturizing sponge impregnated with an antibacterial agent can act as a filter.

Thanks to the pores, it can easily retain animal hair, hair, large dust particles. Antibacterial impregnation, in turn, provides disinfection.

The following instructions will help you assemble a humidifier and air purifier with your own hands:

Take a plastic container (box) and make a cutout on the side. The height of the cutout is approximately ½ of the height of the filter itself.
Fasten the filter with plastic ties.
Next, we form a cutout in the container lid. The size of the cutout depends on the size of the fan.
Attach the fan to the top of the tank.
We pour water into the structure. The water level must not reach the point where the cutout for the filter on the side of the box begins, otherwise leakage may occur.
We turn on the fan.
The filter must be changed periodically. If you notice that the sponge has darkened, most likely you should replace it with a new one.

ultrasonic humidifier

If you decide to do ultrasonic humidifier air with your own hands, then for this you will have to stock up on a few more special devices. So, you will need:

ultrasonic steam generator (piezoelectric element);
computer cooler;
plastic tank up to 10 l;
cup;
power unit;
any flexible pipe, preferably corrugated;
stabilizer;
an integral part of a baby toy (pyramid) in the form of a donut;
aluminum corner.

The final cost of all assembly parts will not exceed 1000 rubles, which is much more profitable compared to a "store" humidifier. So, let's start creating the structure:

We drill holes in the lid of our plastic container with a drill. Keep an eye on the diameter of the holes obtained: in the future, fasteners from the cooler-fan, an output flexible tube and wires of the ultrasonic piezoceramic steam generator element will be inserted there.
Screw the fan to the tank and insert the corrugated pipe into the prepared hole.
The steam generator needs to stay on some kind of surface. To do this, we will make a platform floating in the container, on which we will install the steam generator. The platform can be built from a measuring plastic cup and a donut from a children's pyramid. Place the cup in the bagel, making a small hole in the bottom of the cup beforehand. Attach a piece of dense fabric to the bottom with an elastic band - it will act as a filter.
Install the UV converter in the beaker.
This device operates on the basis of direct current voltage 24 V. For normal operation of the fan, 12 V is enough, so the power supply can be regulated thanks to the stabilizer microcircuit.

This model of humidifier requires the constant presence of water in the tank. Also make sure that the water is distilled, otherwise the device will quickly fail, scale will appear.

Conclusion

Creating a humidifier at home is not at all difficult, and sometimes very exciting. This will save a lot of money, as well as develop the skills of a novice master. And the final effect of do-it-yourself humidifiers is sometimes not inferior in quality to factory models of famous manufacturers.

Affects the human body a large number of factors. One of them - the relative humidity of the air - affects the constant body temperature and mood. In summer periods, the body suffers from a lack of moisture: the air is dry, intense evaporation negatively affects a person, often he becomes ill, drowsy.

The problem was solved by air humidifiers - devices based on the release of moisture into the atmosphere in order to increase relative humidity air in your home. How to do it yourself? Let's find out!

Before proceeding directly to work, it is worth understanding the device of the humidifier. The functionality of this device is to evaporate the water that you pour into the humidifier. To date, 3 types of air humidifiers have been invented.

actually create this device at home is not difficult at all. With a little knowledge in reserve, everyone can afford a humidifier, spending a minimum of effort, time and money!

Bottle option

This type of humidifier is easy to assemble, it does not require knowledge of the device, the only condition is the presence of a central heating battery that is not immured into the wall. What do we need to create this humidifier? Several elements:

central heating battery;
one and a half liter or two liter bottle;
scotch;
long gauze, about a meter;
thick, tear-resistant fabric or rope.

This homemade humidifier does not require electricity, is easy to make and costs minimal money!

Instruction. We use scissors - we cut a rectangle in the bottle about 6 cm wide and about 11 cm long. We take a piece of fabric and cut two identical strips from it.

We hang the bottle with strips so that the hole is on top and the bottle cap is turned towards the battery. In order to avoid mistakes, we fix the structure with adhesive tape. Next, we need gauze - we fold it several times, making a rectangle out of it with a length of about a meter and a width of 10 cm.

We place one end of the gauze in the opening of the bottle, the second we wrap the battery pipe. Pour water - our humidifier is ready!

It will be less efficient than others to humidify the air, since it does not contain elements that heat water.

But you can use your imagination when creating a humidifier - all the decor details you want! What do we need? A few useful details:

Instruction. First, let's prepare a decorative container. It can serve as a basket for bread, and a wicker basket for a picnic.

It is best to work with materials that are not afraid of water. Cover the container with all necessary details. I advise you to use stones - they go well with water.

Next, place the water container without liquid in a decorative container. It is advisable to glue them to each other. After we line the bottom of the water tank - use sand, stones, figurines, just use your imagination! Do not forget: stones and other elements other than sand should be fixed with glue.

After the whole structure is ready and the glue has dried, you can safely fill in water and enjoy. fresh air in the room!

I note that the drying time of the glue depends on the glue itself. We advise you to use superglue - it is not afraid of water and seizes in a couple of minutes.

Expanded clay humidifier option

You won't find a humidifier like this very often. Not every day a couple of kilograms of expanded clay may appear at hand. In fact, this humidifier is great for the home. It is easy to make at home, but you will need parts that are not always at hand. So what do we need to make? The following elements:

Instruction. To begin with, it is worth connecting two wastebaskets that are small in size. This can be done using household or plastic fasteners. This building is the future housing for the humidifier. It must be durable.

Next, you should connect two large wastebaskets in a similar way, but at the same time the two connected wastebins should be inside. To fill expanded clay in the bottom of the upper large bucket, we make a hole.

Expanded clay should be taken according to the size of the "holes" of the trash can - it is important that it does not spill out of the holes. We put the pump from the aquarium on the bottom of a 12-liter bucket, we draw the tubes from it to the very top.

We install a structure of 4 wastebaskets on the pump, fill in expanded clay. The pipes will return the water to the top. The final detail is a computer cooler mounted above a hole in the bottom of the top trash can. It will distribute steam throughout the room.

Despite the manufacturing costs, this device perfectly humidifies your home in a fairly short time. You just have to remember to add water!

Humidifier option from a bottle and a cooler

A cold steam humidifier costs a lot of money. You can create its analogue using a computer cooler and a ten-liter bottle of water. The price of such an analogue is about 3 thousand rubles, which is many times less than the cost of a real humidifier. Note that making this humidifier is easy even at home. What will we need? A few details:

Also, be careful when plugging in the cooler - we advise you to position the humidifier so that it is not near the sockets. It never hurts to follow the safety rules!

These options for humidifiers will help without extra costs make the air in your home fresh and pleasant!

Normalization and maintenance of indoor air humidity at the recommended level is one of the most important tasks for a person's well-being. The simplest DIY humidifier will improve your well-being and protect your health. How to make a humidifier with your own hands from a bottle and not only a way

Assembling a humidifier with your own hands

The well-being of a person often depends on numerous factors, including the humidity of the air in the room. Moisture index atmospheric air, acceptable for human life, is approximately 50 to 60%, in winter period it drops significantly due to heating devices. Dry air is dangerous for several reasons:

the mucous membrane of the eyes dries, which can lead to conjunctivitis;
the nasopharynx dries up - leads to respiratory diseases;
dry mouth and throat reduce resistance to various inflammatory diseases;
the content of dust increases, which causes allergic reactions.

It is very important for the home that normal air humidity is present in recreation areas, since during sleep a person is more vulnerable to illness.

Simple options for humidifying the air at home

It is not always possible to buy or interrogate men to make a humidifier in the house with their own hands from plastic tableware. Therefore, a few recommendations for women on how to assemble a simple do-it-yourself humidifier:

put a container of water near the battery, lower the edge of the wet towel into the water tank, and spread the rest of the canvas over the heater;
install a container on the battery and periodically add water to it, it is desirable that the container is metal, and the moisturizing effect is achieved;
put glassware, such as an aquarium, a vase or a simple jar, lower an ordinary aquarium compressor into it and put a small fan next to it, better cooler computer. For an aesthetic appearance of this humidifier, you can put in a transparent dish glass pebbles and plastic figurines, they will imitate ikebana.

An elementary way is to start a large aquarium with all the equipment, although it is simple, but not cheap.

DIY humidifiers, step by step instructions

Why buy expensive equipment when with the help of the simplest items and a little ingenuity you can make a household homemade humidifier. The scheme of the humidifier is simple, the main thing is to choose suitable container and attach it to the heater. It is not always possible to find the funds to purchase a factory-made vaporizer, and a plastic bottle is almost always at hand. Consider the simplest ways to make a humidifier with your own hands:

Air humidifier from a plastic bottle. Any bottle of mineral water, lemonade, etc. will do:

in the body of the bottle, an arbitrary-shaped hole is cut out with a width of not more than 2 cm;
with the help of ropes, adhesive tape or ribbons, the bottle is suspended from the upper pipe of the radiator with a gap of 3-5 cm, so that it does not turn over;
done with gauze or bandage thick wick, the gauze is twisted into a strip, and the bandage is folded into several layers about 1 m long;
one end of the bundle is lowered into the slot, the other is wound around the battery, for more effective work humidifier from a plastic bottle with your own hands, you need to put 2 harnesses and breed them in different sides. Then the evaporation area will increase;
pour water into the container and add as needed.

The disadvantage is that a humidifier from a bottle is a device of local action, that is, air humidification in an apartment occurs within a radius of no more than 3 m.

Homemade mechanical humidifier from a plastic bottle. Necessary:

take a bottle with a capacity of 5 liters. and cut a hole in it for a cooler from a computer;
fix the cooler with adhesive tape so that it does not fall inside the container;
connect the fan using the power supply from the phone, and the humidifier is ready for use.

Do-it-yourself ultrasonic humidifier is more difficult to assemble, but more efficient. Small costs and the following elements will be required:

ultrasonic steam generator;
container or bottle 5–7 liters;
plastic disposable cup;
ring from a children's pyramid;
corrugated tube of small diameter;
power supply converter and fan from the computer.

holes are made in the lid: for cooler fasteners, laying wires from the steam generator and arranging corrugated hose or tubes;
the fan and the tube are mounted on the cover on opposite sides;
a hole is made at the bottom of the glass and with outer side a piece of cloth is stretched to filter the water;
a steam generator is placed inside the glass and tightly closed with a toy ring. The cord from it is brought out through the hole of the ring; we connect the current converter to the cooler and the steam generator, pour water into the container, lower the glass and close the lid tightly.

The principle of operation of such a humidifier with your own hands is very simple. The ultrasonic device forms water vapor, and with the help of a cooler and a tube, they come out. The ring from the toy plays the role of a float so that the steam generator stands on required level. It is advisable to fill the water into the ultrasonic steam generator with purified water in order to prevent white coating on furniture. Instead of a toy ring to attach the ultrasonic humidifier, you can use a piece of foam, cut a hole in it and insert a cup into it.

A simple humidifier from a bucket and expanded clay. To assemble a homemade humidifier you will need: four waste baskets, different diameter; fan from the computer; a bucket of about 12-15 liters, so that it includes a large basket.

Assembly step by step:

baskets of the same diameter are placed on top of each other and fastened together with a hair dryer or plastic fasteners. And first, smaller diameters are connected, and then baskets with a larger diameter are assembled around them. Thus, a two-case construction of the thermos type is obtained with containers built into each other;
in the upper outer part, a hole is cut out for filling expanded clay. The diameter of the crumbs to be poured must be larger than the holes in the baskets;
an aquarium pump is installed at the bottom of the bucket. Tubes from it are thrown to the top of the structure, ending with a ring with holes through which water, flowing around the entire perimeter, wets the expanded clay and drains back into the bucket;
the cooler is installed at the top of the humidifier and blows air into the interior. Through the holes in the baskets, passing through the wet expanded clay, enriched with water vapor, it comes out.

Expanded clay for a humidifier must be thoroughly rinsed before backfilling warm water, it performs not only the function of a moisture accumulator, but also a filter. Since the room air passing through it leaves microparticles of dust and dirt on the surface.

It is not difficult to assemble a homemade air humidifier with your own hands, but in addition to elementary humidification, you can achieve cleansing in the premises and assemble a sink.

Instructions for making an air purifier

Dust particles and bacteria in the air are not noticeable, and even a constant wet cleaning unable to remove them. Factory-made air washers are very expensive and not everyone can afford. It is possible to make a humidifier-air purifier with your own hands using improvised materials. For example, how you can use old disks:

the surface of the discs must be sanded, the gloss removed, plastic pieces soldered to the edges;
put prepared disks on a tube with a diameter of 15 mm, alternating with plastic washers 3 mm thick;
in rectangular shape install several coolers from the computer to draw in air;
install a shaft with disks and connect a small toy motor to it;
install a fan in the lid of the container to extract humidified air;
fill with water, so that it does not reach the coolers and plug it into the network.

An air purifier assembled in this way at home can be used not only in houses and apartments, but also in other utility rooms.

For poultry entrepreneurs, it is easier to assemble a humidifier for an incubator with your own hands than to buy expensive factory equipment. Humidity and purity of air in such rooms are very important for a young brood.

Air Dryer

Important for general well-being has moisture content in the air. There are production facilities and premises where the level of humidity exceeds allowable norms and have to dry the room. It is easier to make a dehumidifier with your own hands than to buy a ready-made one. This will require an old freezer. Air dehumidification occurs due to its condensation. Therefore, surfaces are needed on which moisture settles and collects:

a sheet of plexiglass the size of the freezer door is installed in an open opening;
a hole is cut out on the glass, and a fan is installed so that it sucks air from the room;
holes are drilled in the upper part of the glass for the outlet of treated air;
a condensate drain pipe is installed in the lower corner.

Having considered various ways changes in air humidity, it can be concluded that for own health no need to run to the store and spend exorbitant funds. You can, having thought over how to make a humidifier yourself, and, having picked up everything you need, assemble the device. By measuring the humidity in the room, own hands further humidification, dehumidification and purification.

The structure is ready for operation. Due negative temperature on the walls freezer moisture in the atmosphere is attracted to them. The air dried in this way is vented to the outside. This device can reduce humidity up to 10%. It must be taken into account that the air at the outlet has a lower temperature.

How to make a humidifier at home: from a bottle Dry air in an apartment - frequent problems with health. Older people, small children suffer the most from dryness in the room. How to make a do-it-yourself humidifier from a bottle and not only

How to make a humidifier at home: from a bottle

Dry air in the apartment is a common health problem. The elderly, young children, asthmatics, and family members prone to allergies suffer most from dryness in the room. The natural humidity in the room should be at least 40%. If the percentage of humidity is less, dryness in the throat will be felt, there is a risk of developing bronchitis, asthma, the skin loses its healthy shade, the hair becomes dull and loses its shine.

Dryness in the throat indicates that the mucous membranes are overdried. This leads to the fact that microbes will more often penetrate into the body, it cannot cope with such a flow of bacteria, and therefore, against the background of dry air, frequent colds will occur.

The bronchi can no longer clear themselves, leading to respiratory problems. Dryness in the room is also felt by people who wear contact lenses, their mucous membrane of the eye quickly dries out, and the “dry eye” syndrome develops, this is manifested by unpleasant sensations in the eyes and sharp pain.

To avoid all this, you need to purchase a humidifier, or make a humidifier at home with your own hands. We will talk about this in this article. And so we went:

Do-it-yourself humidifier from a plastic bottle

Let's take a closer look at how to make a do-it-yourself humidifier from a plastic bottle. This makeshift device can be left in the children's room, and it will do its job. At the same time, it will not kill anyone with electric current, like a humidifier from a computer cooler, will not leave a coating on things, as happens with ultrasonic humidifiers, and is not harmful to health.

To work, you will need a 2-liter plastic bottle, wide adhesive tape, scissors and a central heating battery. Additionally, you will need either gauze or a long piece of cloth. Everything is ready for work. Cut a long hole in the bottle 6 centimeters wide and 12 centimeters long.

The hole should be on the side. Next, make two wide ribbons that will attach the bottle to the battery. Glue the junction of the ribbons and the bottle well with adhesive tape so that the bottle does not fall. Next, cut two wide strips from the fabric, wet them with water. Hang the bottle from the battery, pour water into the hole and put one end of the ribbon into the water, and put the other on the battery.

Homemade humidifier is ready to use. Now you need to periodically add water inside the bottle and there will be humid air in the room.

How to humidify the air in a room without the use of chemicals

Dusting and damp cleaning the room will help get rid of dry air. But, you can't use household chemicals. Thus, moisture will naturally saturate the air. Additionally, ventilate the room several times a day.

It is worth recalling that in frosty weather, airing will be irrelevant. There is almost no humidity in the frosty air. Remember how difficult it is to breathe on the street when it is 15 outside the window. Humidify the air in the room will help ornamental plants. They not only humidify the air, but also absorb toxic substances, carbon dioxide ionize the air.

In addition, they perfectly decorate the interior. For support natural humidity can be grown indoors hibiscus , ficus, home fern, ornamental linden, geranium . It will be interesting to look at a small greenhouse in the room.

To cope with the problem of dry air in the room, a small decorative fountain or aquarium with fish . Additionally, you can spray water from a spray bottle on plants, curtains, just spray around the room.

In winter, you can put a jar of water or a basin near the battery. Under the influence of heat from the battery, the water will evaporate and saturate the air. When using this method of humidifying the air, remember that the water in the container must be changed every day.

If this is not done, microbes will develop in it, which can cause colds. You can solve a one-time problem with dry air in a room using the above methods, but if you want a long-term effect, you need to go the other way.

How to make a humidifier at home? This question has visited everyone who is faced with dry indoor air, but does not want to use chemistry.

How to humidify the air in the room: ways

If you are not satisfied with any of the above ways to humidify the air, you can look at ready-made humidifiers. They There are several types: ultrasonic, steam and conventional. The conventional humidifier is popular because it forces dry air through the valve where the wet sponge rests. It turns out interesting system: dry air enters one hole, and wet air comes out the other.

Steam humidifiers photo

A steam humidifier has the same principle of operation as a boiling kettle. It has a water tank and two small coils that heat the water. The water heats up to 70 degrees and begins to actively evaporate, spreading moist air around the apartment.

When the water in the tank runs out, the fuse is activated and it turns off. The device will turn on only when you fill it with new water. Steam humidifiers are not recommended for those who have elderly people or small children in the house.

ultrasonic humidifier photo

Ultrasonic humidifiers are considered the most convenient to use. The device is small in size, runs on electricity, but does not take much energy. Air humidification occurs due to the fact that water, falling on a special plate, breaks into microscopic particles and spreads through the air.

It is important to remember that you can not take water from the tap or mineral water. There is too much salt in it, which will settle on your furniture and things after the water dries. You only need to fill the ultrasonic humidifier with distilled water or buy a special filter for ordinary water.

How to humidify the air in the apartment, everyone chooses for himself. Much depends on the size of the room, the number of family members and their health status, and your preferences. In general, it is better to think about how to make a humidifier at home than to buy ready-made options. By doing the work yourself, you will know that the device will work.

Well, on the undergrowth, as usual, the video:

How to make a humidifier with your own hands video

The easiest way to make a humidifier is to place a small saucepan on top of a battery. The water will gradually evaporate and humidify the air. But, such a humidifier will not last long, and soon you will get tired of messing with the pan.

The principle of operation of air humidifiers and how to make a humidifier with your own hands. Options for making an air humidifier from a plastic bottle, expanded clay How to make a do-it-yourself humidifier from a bottle and not only a method

DIY homemade humidifier - 3 manufacturing options

Russian "kulibins" are brainy people and making a humidifier with their own hands is a trifle for them. Moreover, the principle of operation of the device is simple. Consider the most popular options for making a humidifier for the home and try to give detailed instructions for each of the proposed methods.

How does a humidifier work

These devices evaporate the water poured inside, and then supply the formed steam together with the air into the room. You can even "draw" the following picture: a basin with water and a towel dipped into it. This simple humidifier can also be used in everyday life, however, it is ineffective, since it humidifies the air only in its immediate vicinity.

Modern units work a little differently. Cold steam appliances atomize moisture with a fan and fine mesh, steam ones use the principle of operation of an iron (a heating element immersed in water evaporates it and “pushes” the resulting steam out), ultrasonic ones convert water into a water cloud using a piezoelectric element that produces high-frequency vibrations.

Bottle option

To make a "bottle" humidifier, you will need:

central heating battery (not wall-mounted)
one and a half or two-liter plastic water bottle (of course, empty)
wide tape
a strong long piece of cloth or rope
gauze about a meter long

This homemade device does not consume electricity at all, is easy to assemble, does not leave salt deposits on objects in the room, as is usually the case with ultrasonic devices that are now popular. But the most important thing is that it does not require any financial investments, well, unless you have to buy scotch tape, gauze and drink a half-ton of mineral water.

Manufacturing instructions

Using scissors, we cut a hole in a plastic bottle 10-12 cm long and 5-7 cm wide. The slot should be located on the side.
We cut off a piece of fabric and from it two long strips of the same size. We hang the bottle for these ribbons to the pipe extending from the "accordion" so that the cut hole is at the top
For greater strength and reliability of the structure, we fix the junctions of the bottle and ribbons with adhesive tape
We take gauze and fold it several times. You should get a rectangle 1 meter long and about 10 cm wide.
We lower one end of the gauze into the opening of the bottle, and wrap the other around the pipe. You can even enhance the moisturizing effect by taking two pieces of gauze and constructing two wicks.
Using the second bottle, pour water into the hole.

How to make a humidifier from an old bucket and expanded clay

Expanded clay can both absorb moisture and release it.

four trash cans (two smaller, two larger)
twelve liters bucket
aquarium pump
computer cooler with a diameter of 140 mm
household hair dryer
plastic ties

Crafting Instructions

Connecting two baskets small size. They are connected along the rims with the help of household hair dryer, but if suddenly it is not there, then you can get by with plastic fasteners. You should get a body of the future device, hollow inside.
Two large baskets are also connected, it is only necessary to first place inside them the case you already have from small baskets. As a result, you have a two-layer unit on your hands, resembling a thermos in its shape and purpose, consisting of four plastic buckets.
The bottom of the upper large basket must be cut with a knife or simply cut a hole in it for filling expanded clay. Expanded clay must be taken in such a size that it cannot "leak" through the holes of the baskets.
An aquarium pump is placed at the bottom of a twelve-liter bucket, and the tubes from it are led to the very top of the structure. A plastic ring with holes is located "on the top" of the future humidifier - from these holes, moisture will flow down the expanded clay back into the bucket.
At the top, you need to install a computer cooler that will force air into the expanded clay walls saturated with moisture, and then “drive” it out through the holes in the baskets.

The principle of operation of the wastebasket construction is based on the "work" of expanded clay, so it is worth paying more attention to this particular "ingredient". Select the granules carefully, and before pouring them into the device, be sure to rinse all the expanded clay with warm water.

Humidifier bottle and cooler

A cold steam humidifier costs 1,500-3,000 thousand rubles in a store. But its price can drop a hundred times right before your eyes. To observe this incredible spectacle, you will need one bottle of water (preferably a ten-liter one), one computer cooler and scotch tape.

Manufacturing technology

Cut off the bottle upper part with a neck so that a cooler can be installed in the resulting hole.
Attach the fan to the bottle with tape. You can take some thick cardboard, make a slit in it a little smaller than the cooler body and attach it to the bottle with the same adhesive tape - it will be more reliable.
Plug in the fan.

These simple options products for moisturizing are sure to come in handy. Even if not in a city apartment, but in the country. Air everywhere and always should be comfortable.

Using this simple knowledge, you can make such a design yourself.

Do-it-yourself air humidifier from a plastic bottle to a battery. How to humidify the air in the apartment without a humidifier? Homemade ultrasonic humidifierHow to make a do-it-yourself humidifier from a bottle and not only a way

How to make a humidifier with your own hands?

reland. en » Crafts » How to make a humidifier with your own hands?

Make your own humidifier it is possible both from improvised means, and using additional materials and devices. AT this material we have collected the most interesting options similar useful device for home.

The role of the humidifier

Before you do humidifier at home, you need to understand what it is, in general, needed. Air normal humidity in the room is particularly difficult to maintain winter time, since central heating dries it out very much, and breathing dry air is fraught with consequences. Among them are respiratory diseases, allergies and other troubles.

All humidifiers perform one important function, they maintain the humidity level in the room at the level of 40-70%, namely this indicator is considered optimal for a person.

Humidifiers for battery

Do-it-yourself humidifier on a battery it is very simple to do, for this you need to have a heating battery that is not walled up in the wall. From the materials for manufacturing you will need: a water bottle ( 1.5-2 l); adhesive tape, wide is better; a piece of cloth; gauze meter long.

So, the production sequence:

Cut a window in the bottle up to 12 cm long, up to 7 wide. This must be done in the side.
Hang the bottle with the slot up from the pipe that comes from the battery. To do this, use a rope or fabric cut. To this design not turned over, glue the place where the bottle comes into contact with the fabric with adhesive tape.
Take the gauze and fold it several times, so that a strip up to a meter long and about 10 cm wide comes out.
We lower the resulting piece of gauze into the bottle with one end, and wrap the other around the pipe, if you wish, you can make several such cuts, then the effect will increase.
After preparation, you can start the humidifier - pour water into it.

Another option for a battery humidifier is this: with the help of a rope threaded through the holes, you need to fix containers on the accordion, water from which will not spill. You can use light oblong vases, in addition to their main function of moisturizing, which will occur as a result of the evaporation of moisture from them, they will definitely become an interior decoration. If you don't want to look for similar decorative elements, you can do it even easier - put a metal container with water on the battery and that's it. True, in this case, perhaps in the end heating season you will have to say goodbye to her, as serious scale forms in the tank after tap water, as a way out, use several, while one is “working”, the second is undergoing a cleaning process.

Homemade humidifier made of expanded clay and a bucket

The expanded clay material has excellent qualities, which give it the ability to become an excellent base for a moisturizer.

In this option, you will need additional materials, such as:

Four mesh buckets (these are used for garbage), two slightly larger and two smaller.
A bucket, optimally 12 liters.
Aquarium pump.
Cooler from a computer with a diameter of 14 cm.
hair dryer ( building), which has high temperature heating.
Ties ( plastic).

The first step in the manufacture of such an air humidifier will be gluing buckets, those that are smaller together. This can be done with a household hair dryer, if there is none, then plastic fasteners will do.

Thus, we get a humidifier case, which has a void inside. You also need to connect large buckets. Before doing this, place the first creation inside.

To fill the voids in the humidifier with expanded clay, you need to cut off the roof at the upper container or cut a hole into which it will be convenient to fill it. Please note expanded clay should be chosen with such a fraction so that it does not wake up through a mesh bucket.

Now a bucket of 12 liters comes into operation, an aquarium pump is placed on the bottom of it, and its tubes are brought to the top of the construction of mesh buckets, then we install a plastic ring with holes on top.

On top of this whole creation, you need to mount a cooler, it will blow air into the expanded clay structure, which are saturated with moisture, and then moisture will enter the room through the holes.

Plastic bottle humidifier

Is easy to implement 10l) plastic bottle, computer cooler and scotch tape. Assembly sequence:

Such a humidifier can be made from a large plastic container, due to the fact that such containers have legs and a tight lid, as well as a much larger volume, it will be more convenient for you to use this option.

In this case, you need to cut a hole directly in the roof of the container, all other steps are similar to the previous one.

Humidifier from a plastic bottle, video:

plastic box humidifier

A slightly more complicated option, but also more effective. For such a humidifier, you need to take 2 plastic crate, one is larger - 30 liters, the second is smaller, it should be mesh and fit into a large one. In addition, gauze is needed ( bandage), wire or fishing line, fan.

It is made in this way:

Thanks to the use of a fan, the system works very quietly, without creating discomfort for the residents of the apartment, the water consumption is about 1.4 liters in 6 hours, it will be 5.6 liters per day - a very good option, and most importantly, effective.

Humidifier-air purifier, video:

ultrasonic humidifier

Create do-it-yourself ultrasonic humidifier quite realistic, but for this you have to use some special materials. For such a humidifier you need:

Ultrasonic transducer.
Computer cooler.
Plastic container for 5-10 liters.
Plastic cup.
Bagel from a children's toy pyramid.
Power Supply.
Corrugated pipe or any flexible.
Stabilizer.
Aluminum corner.

After you have purchased everything you need, you can start assembling. Use a drill to make holes in the lid plastic container. You will need to insert the fan mount, outlet tube, and steam generator wire into them. After that, screw the fan to the container and insert the corrugated tube.

For the steam generator, make a special floating platform that will be in the water all the time, thereby ensuring smooth operation ultrasonic humidifier.

But what to make such a platform from? And it's simple - take a plastic cup and a round piece that will have a hole in the middle. You can take this from your child, namely the part from the pyramid.

Insert a glass into a bagel, drill a hole in the bottom, and then attach a piece of fabric to its bottom with an elastic band. The fabric will act as a filter, then insert the steamer into the glass.

Its best work will provide a constant or variable resistor. It is better to hide the microcircuit, the speed control knob under the aluminum corner.

This unit does not need special care, the only thing you need is to make sure that there is always water in it, and one more important point it must be distilled.

Floor fan humidifier

If you don’t have time to make something at all, and you want to breathe normal air right now, then you can make such a humidifier: fix a dense mat on the pipe, which you pre-moisten, hang this structure, for example, on a floor lamp, slightly higher than the height of your fan . Behind a similar design, put a regular floor fan and turn it on. It is important to constantly keep the rug moist, only then there will be an effect, however, at the end of the season it will most likely have to be thrown away, since stubborn salts and rust are unlikely to be washed off.

Humidifier from improvised materials, video:

Air humidifier with antibacterial filter

For such a device, you will naturally need a filter, in addition, a low-speed fan ( 12V) and a plastic box.

The assembly process is not particularly difficult. AT plastic container, in the side part you need to make a cutout about half the height of the filter, then you need to fix it with plastic tie or in any other way.

A fan is attached to the lid of the container, for which a hole is prematurely cut out. The last stage is the filling of water, its level should be slightly lower than the height of the side cut. Everything is ready, it remains only to plug it into the outlet.

Another version of the humidifier will have a similar design, only instead of a filter there will be gauze, and for the convenience of pouring water in the container lid, you can make a hole of the same diameter as the neck of a watering can.

Its advantage is the absence of the need to purchase a filter. For an additional effect, you can add a few drops to the water. essential oil, while there will be moisturizing and aromatization.

Decorative humidifier

All these designs are not very attractive, if you crave aesthetics in everything, then this humidifier option will suit you.

In order to make it, you need to take a bowl, preferably blue or blue color. Inside it and at the edges, you can stick pebbles with special glue, if there are plastic fish, then they will go too - in general, create a marine entourage, you can throw pebbles on the bottom. Pour the whole thing with water and put it near the battery.

You can make any stylization that you like and what your imagination is enough for. It will be especially interesting for children to watch such a humidifier, and they will certainly help you replenish water resources in him.

Is easy to implement DIY humidifier from a plastic bottle, which will give the effect of cold steam. For this you will need a large 10l) plastic bottle, computer cooler and scotch tape. Assembly sequence.

Categories

Popular