How to make a round lampshade with your own hands. Original lamps and lampshades with their own hands. Ideas, master classes. Wine bottle chandelier

Home textiles are an integral part of the appearance of any room. The lamps are playing important role in the interior, being responsible not only for the ability to correctly illuminate the room, but also bringing an aesthetic component to its walls.

A properly selected lampshade can become a harmonious addition to an existing interior. In addition, with its help you can update the design, which is already rather boring. In this case, you do not have to spend money, especially if you do everything yourself

What can be useful when making a lampshade for a floor lamp with your own hands?

any beautiful fabric;
a thread;
needles;
scissors;
sewing machine;
pin;
thin elastic band;
ruler or centimeter;
soap.

Preparing materials for a new lampshade

A table lamp is perfect for making a beautiful lampshade from old things that are already shabby, but which the hand does not rise to throw away. Such a product, designed with my own hands, will look great in a bedroom or living room, especially if you make a lampshade from the leftover fabric from the curtains that hang in the room. To determine the size of the future lampshade, think about the width of its upper and lower parts. For convenience, you can use a thread that measures required size. After that, just write down the data.

Take the prepared fabric and fold it in half, pin it with needles. cut fabric better fabric at an angle. Thanks to this method, the cutting fabric is much better stretched, and in the future it will be able to fit perfectly into the size of the lampshade, this will greatly facilitate your task. The resulting cut is marked with chalk or soap, highlighting the top and bottom.

Making a lampshade

Connect one end of the top line to the other end of the bottom line. It is necessary to leave allowances for the top and side seams about one and a half centimeters lower. This is followed by processing the edges of the fabric along the perimeter with a zigzag seam. Then tuck the bottom and top edges in, baste them lightly and evaluate them on the lamp. If all goes well, sew the seam tightly on sewing machine. Fold the fabric in half and repeat the same operations with the side seam, leaving about a centimeter for the allowance. Take a pin and use it to thread the rubber band through the bottom seam of the lampshade, and then sew the rest of the seam.

Put the finished cover on the old lampshade and carefully sew them together with a needle and thread. You should not fix the products very carefully, because a new lampshade must be removed from time to time for washing so that the lamp always maintains an excellent appearance.

As you know, a floor lamp is a lamp standing on the floor and supporting the lampshade with a rod. The word "floor lamp" came to us from French, which in translation means "torch". Of all the variety of lighting fixtures, floor lamps, without a doubt, are the most homely, cozy and comfortable. Soft, diffused light quietly flows from under the lampshade and pleasantly illuminates the space.

Since the time when grandmother's floor lamp with a shelf on a leg, the lampshade of which was decorated with fringe, was a family heirloom, passing from generation to generation, the calming light of a floor lamp has been associated with peace and home comfort. After some oblivion, floor lamps are experiencing a period of rebirth. Now they can be seen again in almost every home. Bright, sometimes even blinding light, like loud sounds, can not only tire, but also irritate, so twilight is sometimes simply necessary. A floor lamp in this sense, a miracle how good and quite capable of bringing to life peace of mind and tranquility.

Room lighting is practically the main aspect in the interior. By combining light with shadow, we somehow create a mood in the house. central lighting for all its attractiveness and economy - once and for all to illuminate the entire room, does not create coziness and some, hmm ... sincerity is a completely different matter, lamps with subdued light, different kind sconces, table lamps and, of course, floor lamps. The latter, well, just the same aristocracy among the lamps.

Of course, the main function of a floor lamp is to provide a certain level of illumination of a room or part of it, but their usefulness does not end there. Whatever, not for dinner will be remembered, the designer would say that the floor lamp helps to "zone" the space. Obviously, the area in which the floor lamp is located is intended for relaxation - with a book, in easy chair and with a cat on my lap. In addition to the obvious functions, there is also an underlying functionality - decoration. You can choose an option for any style of interior. There are models that will successfully fit into the interior and will not distract attention to themselves; in contrast to them, there are many floor lamps that can become a sort of highlight of the interior of a living room or bedroom, and even a pantry. It all depends on what effect we expect from the presence of a floor lamp in the room.

If we talk about the advantages of floor lamps compared to wall or table lamps, they have a number of obvious advantages:
to install a floor lamp, there is no need to drill holes in the wall (as is the case with wall lamps - sconces);
the floor lamp is mobile, we can move it to any place, turn it in any direction, as long as there is somewhere to put a socket nearby;
depending on the height of the floor lamp, it is able to visually increase the height of the room.

Floor lamps with lampshade, this is the most classic version floor lamp, consisting of a stand, a high tripod and a lampshade fixed on its peak. It is the lampshade that is responsible for specifications device, the level of dispersion and background illumination. Well, the main contribution to the attractiveness of the lamp as a whole, as a rule, is behind it, behind the lampshade.

A lot of materials are traditionally used as a material for the manufacture of a lampshade - fabric, fiberglass, glass, paper, ceramics, metal and plastic, well, all sorts of designers with homemade ones not deprived of imagination, sometimes they will use such that at least take out the saints.

Having decided to make a small table lamp, we were faced with the task of making a lampshade. It was decided to make it rag, for this a wire frame was needed. Since it was available, I used it.

What was used in the work.
Instruments.
A set of small metalwork tools, a mallet, scissors for metal. Good cutters. 65W soldering iron with heat regulator, accessories. Definitely a circle. Jewelry jigsaw with accessories. Small brush for flux, sandpaper. For varnishing - dishes, brush.

Materials.
Galvanized steel wire with a diameter of 2mm. Solder POS-40, flux - "soldering acid" (zinc chloride). A small piece of galvanized steel. LMB, rags.

This kind of lampshade at the factory is traditionally made in the way resistance welding, here, for the lack of such, soldering is used.

The wire was first used galvanized steel. The previous frame and similar work was made of brass, for easy soldering. But the cost of a brass wire that went to one frame was approximately equal to the cost of a whole bay of galvanized steel, from which more than a dozen such gizmos can be made. Practice has shown that the assembly is no less convenient, soldered, galvanized steel, with the selection of the appropriate flux is good. "Soldering acid" was used - zinc chloride. And the usual tin-lead POS-40.

First of all, we form "parallels" - rings. The wire was sold in the form of a small bay, and the cut pieces strove to curl up into a ring anyway, it was only necessary to correct them a little. To fix the "parallels" in their places, in wooden pattern small cloves are clogged, they do not allow the rings to slip.

Rings-“parallels” are formed and soldered, we proceed to the “meridians”. It is convenient to measure the length with a string, I bit off the wire a little with a margin. Directly on the template "meridian" was molded. On the arcuate part, the workpiece had to be straightened a little, reducing its radius; in the lower part, the workpiece was straightened almost completely. Marks were made with a pencil on a wooden blank, the wire of the "parallels" in these places was cleaned with a medium-sized sandpaper and tinned with zinc chloride. Then the places of soldering at the blanks of the "meridians" were cleaned and tinned, and there was no need to mark them - two ends and a middle-bend. "Meridian" was applied in the right place, the middle was pressed with the left hand in a rag glove, flux was applied and soldered. Then the ends of the "meridian" were soldered, it was even easier, the workpiece was molded so that the middle almost reached its place. After soldering it, the ends were pressed tightly against their "parallels".

For simplicity, the workpiece was marked "visually", by eye, that is. Four "meredians" are soldered, two each, opposite each other. The angle of 90 degrees is well defined by the eye, further, the “meridians” are soldered into the middle of the empty sections, where the marking task is also very simple - to divide the segment in half.

Several times there were such difficulties - a new soldering, next to the old one. No “stepped soldering” with different solders, just “old” soldering was organized with an additional heat sink in the form of pliers sponges. There was not enough heat to melt the solder and everything that was needed remained in place.

Well, the whole disc is evenly covered with “meridians”, but, something is a little rare. I wanted the finished rag lampshade to not have a blatant “facetedness”. It was decided to add "meridians" in the intervals.

Well, this is more like a hemisphere. Let's leave it. Small carnations are pulled out and the frame is carefully removed from the blank.

Now you should take care of mounting it on the lamp. Socket in a lamp with a small E14 base, with a thread on the outside and a large carbolite nut on it. With this nut, the lampshade is clamped onto the lamp.

The platform for the nut was cut with a favorite tool - a jewelry jigsaw with a large nail file. From galvanized "roofing" steel 0.5 mm. A square blank is cut out with metal scissors, diagonals are drawn, at the intersection, the blank is slightly punched. The leg of the compass is installed confidently, without slipping, in this hole.

Paradoxically, straight wires turned out to be not so easy to get - I had to work pretty hard with a mallet on a wooden stump. It was decided to make fasteners at four points, so as not to measure the angles with a protractor (usually, they are made in three - they save wire and it is somewhat easier to get to the light bulb).

Taking on the arrangement of the interior space, it is important to think through every little thing. After all, we all subconsciously strive for comfort and that is the smallest details able to create special atmosphere, hand over general idea, mood and character of the room. Professional designers claim, and the interiors clearly prove that right choice Chandeliers can not only decorate the interior of the room, but also make life brighter, more fun. They give special grace and gloss to the lamps beautiful shades for chandeliers with original design. About how to make them with your own hands and what materials it is better to use for this, you can find in this article. Detailed, step by step master class, as well as visual photo will be a great help to you in this exciting process.

Material selection

In the manufacture of a chandelier, it is difficult to single out any one material that would meet all the requirements. Each of them has its own individual characteristics and features. For example, paper, which is the most simple and available material, lends itself well to transformation.

Lamps made of glass fragments and strips of metal have a dazzling brilliance and a beautiful appearance. Wood and fabric add warmth and comfort to the interior. Lace lampshades are distinguished by their special beauty, captivating everyone at first sight.

In a word, you can make a chandelier with your own hands from anything, the main thing is to be smart in time and turn on your imagination.

A paper napkin chandelier is a bold enough but justified experiment.

We will describe in detail in this article how in an ordinary object you can see its creative potential for creating an exclusive decor element.

Step-by-step instructions, with a description of each action, will help you make improvised, incredibly beautiful and unique lamps, which will become great addition to your favorite interior.

What you need to pay attention to before making a chandelier

Many are interested in how to properly make a chandelier in, and other rooms. After all, I want this element of the interior to be not only beautiful, but also functional.

On the one hand, the chandelier is lighting fixture, capable of providing the proper level of lighting in the apartment. After all, a lot depends on the choice of light in the room, including the safety of the eyes. On the other hand, I would like ceiling structure complemented the interior design, creating a special atmosphere of warmth and comfort.

When making a chandelier, the first thing to consider is the height of the ceiling. For example, a chandelier with a bar mount is suitable for low ones. So, the ceiling will look visually higher. If the ceilings are high - 3 m and above, then it is better to make your choice in favor of hanging lamp with hook fastening.

Lamp selection

For any room you need to individually approach the intensity of its lighting.

For a small bathroom, 80-100 watts will be required.
Kitchens need a lamp power of at least 120-150 watts.
The living room and the hall cannot do without light bulbs in the range of 150-300 watts.

The number and power of lamps is calculated based on established standards - 20 watts are required per 1 m². electricity. It is also necessary to take into account the parameters of the room, its dimensions and reflective properties.

Edison designer lamps - look beautiful and unusual

Plafond design

The appearance, decor and design of the ceiling takes important place in the design of the chandelier. It is selected for the interior of the room, depending on the style. Crystal for classics, metal and glass for, wood will fit perfectly into country or chalet style, fabric and silk are great suits the style provence

To illuminate a room on several levels, you can additionally make wall sconces or floor lamps.

Step-by-step master class on making

To make a beautiful ceiling decoration, it is not necessary to start everything from scratch. Take a look around, you probably have something in your house that you have not used for a long time. And who knows, maybe it will become the main subject in the manufacture original lamp. Moreover, there are more than enough ideas and inspiration for creativity on the Internet.

Important! It is best to start searching for the necessary things from the kitchen or balcony. It is there that we store all sorts of rubbish that was once so necessary for us and which, as often happens, is so difficult to part with later.

Spectacular chandelier from mugs

No matter how strange it may sound, but it is from dishes and other kitchen utensils, the most unusual and interesting models lamps. For example, tea mugs are ideal material to make a spectacular lamp.

For work we need:

Mugs
Saucers
Drill
Porcelain drill with special hole

Mastering quickly and easily

At the bottom of the mug, with a drill, we make a small hole for the wire, fasten the electric chuck and bring the wire out. It is desirable to seal the hole with a gypsum mixture.
Next, the mug must be glued to the saucer, where there should also be a hole, insert a light bulb and hang the newly made lamp in the right place.

As you can see the original fashion design can be obtained from completely ordinary items.

Fascinating yarn chandelier

Since it's pretty a simple product, for its manufacture we need a minimum of things, namely:

Wire with a section of 4-5 mm.
wire cutters
Fine thread
colorful yarn

Manufacturing instructions:

A ring is made of wire, the diameter of which will correspond to the future size of our chandelier. To get perfect even circle, it can be wound on any object that has a cylindrical shape.
We bite off the excess wire with wire cutters, leaving 2-3 cm in reserve on each side. We tie the ends with a thin thread.
It remains to decorate our chandelier beautifully and brightly. To do this, we cut the threads of yarn in such a way that the length of each segment is twice the height of the ceiling.
Alternately, on a knot, we tie the resulting threads until we hang the whole ring with them. From the same yarn, we make a hook mount.

You can use such a lampshade both in the form of a chandelier and in the form decorative element decorating the interior of the room.

By combining the skills of macrame and papier-mâché, you can get stylish chandelier bedroom

Important! To make such a lamp, instead of woolen yarn, you can use any other thread. The main thing is that it harmoniously fits your interior.

Unusual teapot lamp

How to make your own chandelier ordinary teapot, you will learn from this master class. Here's what we need for this man-made masterpiece:

Teapot
The wire
Electrochuck
metal chain

Step by step guide to making

First of all, the bottom of the teapot is cut out. This is done in such a way that the resulting cutting edge is not sharp, otherwise you can get hurt on it.
Next, an electric cartridge is fixed to the lid of the kettle, the wire of which is led out through a small hole drilled at the top.
A chain is attached to the handle of the kettle, through the links of which a wire is threaded. The lamp is ready.

Breathe new life into bottles

glass bottles, especially if they have beautiful shapes, can be used to make a wonderful chandelier. Required material:

thin rope
Flammable liquid (alcohol or gasoline)
Glass bottles (preferably colored)
Edison lamps (having a beautiful spiral)
Wire and electric cartridge

Do it yourself

We wind the rope on the bottom of the bottle, after wetting it in a flammable liquid. Then we set fire to it and let it break, and we begin to slowly rotate the bottle around its axis until the rope burns to the end. After that, we lower the bottle into a container with cold water, wrap it with a towel and, with a little effort, break off the bottom.
So that the cut edge is not sharp, it must be sanded. To do this, it will be enough to twist the bottle in sand or small gravel for a couple of minutes.
It remains to properly mount the electric cartridge, stick the wire through the neck, screw in the light bulb. From the remaining bottles, the rest of the shades are made in a similar way.

This chandelier will perfectly fit into the interior made in any, especially if you hang it over the bar counter.

Can decor

No less beautiful are lamps made from cans. They are made in the same way as from bottles. The only difference is that the bottom of the jar does not need to be cut off, as clear glass is usually used for shades.

We need:

Beautiful thick-walled jars (preferably with a relief pattern)
Hammer and nails
Wire, electric chuck
Paint can
Edison lamp

How to do it right

To begin with, using a nail and a hammer, holes are stuffed in a circle in the lid, after which the inside is gently squeezed out. The diameter of the circle must match the diameter of the socket in the chuck.
We insert the cartridge into the cover, mount the wire.
Next, paint the lid along with the cartridge in the color we have chosen. Metallic paint with a golden tint will look best.
It remains to screw the light bulb, close the lid and install the lamp in its place.

We all know what a globe is, but not everyone knows what amazing things can be done from it. For example - a nice lampshade for a chandelier that will perfectly fit into the interior of a children's room.

Here is everything we need:

the globe
Bulb
Electric chuck with holding element

Step by step master class

Usually the construction of the globe is not solid, so in order for us to get desired element, it is necessary to divide it into equal two parts (hemispheres).
Next, in top point hemisphere, you need to make a hole for the cartridge. For this, it is best to use a drill with a crown.
The electric chuck is put into place and securely fixed by the retaining element. Congratulations, your chandelier is ready!

Suspended antler structure

Making a unique lighting device from deer antlers is quite simple, the main thing is to have the necessary material at hand.

Such designs are famous for their special sophisticated look and are best suited for rooms with high. Such chandeliers are used in many interiors, but they look especially attractive in country, chalet or rustic style.

As a rule, the shades of such chandeliers have various forms and only natural materials are used for their manufacture.

We will need:

Antler
Rope
Copper wire
Electric chuck and wire
Bulb

Make a chandelier like this

Observing the precautionary rules, according to the diagram, we connect the wire to the electric cartridge.
Next, the wire must be beautifully wrapped with a decorative rope. For better fixation, you can use a universal transparent glue.
Via copper wire, in the lower part of the resulting rope, horns are attached, placing them 2 cm above the cartridge.
We repeat a similar procedure with the rest of the shades, then combining them into a single composition.

Update a lampshade for a floor lamp with your own hands, make a new one or repair an old one good idea to give a fresh gloss, a new mood to your home.

How can you make a lampshade for a floor lamp with your own hands, if the old one is worn out or no longer corresponds to the new time or the new tastes of the owners.

Everyone loves floor lamps. This is the most versatile light source. It is so comfortable to sit under it with knitting or a book, it can be moved, it is mobile and is an interior decoration. Therefore, the decor of the floor lamp so attracts the eyes of needlewomen.

Many lamps are inherited from previous generations, and, perhaps, at first, they push it somewhere, but then the aura of old household items becomes attractive. There is a desire to repair old floor lamp, update the lampshade and all this at home.

This is a good idea, now there are so many ideas around and the possibilities for their implementation that it is simply embarrassing to sit idly by. Arrange the constriction of the lampshade on old frame or completely remake the floor lamp, the process will be exciting in any case.

Lampshade frame

From wire disposable hangers

Using pliers, unroll and straighten wire from disposable dry cleaners hangers.

Using a ruler and wire cutters, cut two pieces of straightened wire to the desired length. The length is equal to the length of the perimeter of the floor lamp shade

Use pliers to make a circle with each hook and loop wire to hold the circle together

Measure and cut two pieces of straight wire equal to the height of the lampshade + hem allowance for the hinges

Bend loops at both ends of these wires, use a round stick and pliers

Slip the loop at one end over the circle and pull off, and the loop at the other end over the other circle. Do the same with your own hands with the second wire. To secure the frame structure.

Glue the loops. Adhesive for metal « Cold welding”, “Epoxilin”, “Superglue”.

Cut 4 pieces of wire with a size equal to the radius of the circle minus the radius of the small circle for the bulb, plus hem allowances for the hook. You can calculate the radius from a known circumference using a formula known from school, or you can use online calculator at allcalc.ru/node/783

Make a small circle for the light bulb with your hands from a piece of wire a little longer than the circumference of the light bulb socket plus an allowance for the hook. Connect the wire into a ring and glue the ends

Attach all 4 needles to the big circle and to the small one.

wire mesh

For a floor lamp you will need 2m of mesh 40cm wide

How to sew a fabric lampshade video

What can be made

Do better with what you know how to do. If you knit cool, show off the talent of a knitter, if you embroider boldly embroider a plot that beckons you. The main thing is to do it yourself. Your guests will gasp with delight and admiration.

Fabric lampshade

Highly convenient option if you need to update or repair with your own hands at home. And it happens that the furniture has been updated and you need to change the colors of the accessories. Or is it finally over beautiful embroidery and it turned out to be appropriate for a floor lamp. Padding saves in many cases, see detailed wizard class on the site.

You can make a lampshade for a floor lamp or a table lamp in minutes, or you can create a masterpiece from the world of lampshades with your own hands for weeks.

Master class fabric lampshade. Master class fabric lampshade with paper pattern

Lampshade in macrame technique

A macrame lampshade can be found even on the street, as an attractive advertisement for a store or a cozy cafe.

Thread lampshade

Surprisingly, threads have been used for this purpose for several decades. The threads create a particularly cozy look, whether they are tightly attached to each other or scattered in sparse, light, elegant weaves.

Choose threads for harmonious combination with room interior
Use dense, thin threads, they hold their shape and color better. Loose gain glue and become faded.
Before winding the threads, evenly grease the ball with petroleum jelly
Use transparent glue that becomes glassy when it dries.

For a black lampshade, we took a skein of black satin thread and 2m of strong black braid.

crochet lampshade

Crocheted lampshades look incredibly cute and cozy at the same time, and at the same time can be exquisitely stylish. Create an exclusive thing with your own hands. Even for beginner knitters, crocheting in a circle is a simple thing. And for experienced needlewomen, a whole expanse of ideas is more complicated.

A lovely lampshade for a flat kitchen lampshade is crocheted according to the scheme. The diagram is attached below.

Wooden lampshade

Wooden lampshades are made from slats or from a single piece of wood. The mind-blowing video shook my imagination.

Video how to make a floor lamp from a log with your own hands

A selection of photos for inspiration and pleasure

Ideas used in the article:

lazuli-handmade.nl, http://marrietta.ru, arxip.com

Always with you, It's beautiful here.

Decorating lamps or creating lampshades is not only interesting, but also useful. You can get the perfect item that matches the interior of your home and still save a lot of money. You just need to buy the simplest lamp, and make it exclusive.

cozy house- this is not only the right furniture, but the right lighting. Thanks to beautiful lampshade, the interior will become exclusive, and the room will become warmer and more comfortable.

If there is a desire to make a rearrangement in the room, then along with it you need to update the chandelier and floor lamp. You can buy just a new product, or you can change the textiles on the lampshade with your own hands.

A detailed master class on making a lampshade will help you create a unique, decorative piece of furniture. Getting to know everyone possible ways production, you can choose for yourself exactly the option that will be ideal for you.

Lampshade material

Having finished frame, you can start choosing the material for the lampshade. It could be:

the cloth;
plastic;
Knitting;
leg-split;
beads;
paper.

Suitable and waste materials, which are usually thrown out:

egg cartons;
newspapers;
gift wrapping;
old spare parts for a bicycle or car, etc.

Choosing the material for the lampshade, you need to remember its color. It should perfectly match the created style. In addition, you need pay attention to room lighting. If the room is poorly lit during the day, and there is twilight in it, then a lamp made of transparent or light material. For a bright room, you can choose a dense and dark material for the lamp - but this will depend on the overall decoration of the room.

As you know, red yellow add warmth and light to the room; therefore, in order to make the room warmer, you need to install a lamp with a yellow or red lampshade in it. If the room is located south side, and the sun warms up its walls all day, then the lampshade for the lamp installed in this room can be blue or green.

Gallery: do-it-yourself lampshade (25 photos)

How to make a frame for a lampshade with your own hands

The frame is a stable base, mainly consisting of two circles. Circles can be both different and the same diameter; they are interconnected by vertical partitions. The length of the partition is the height of the lampshade.

To make frame cylindrical shape , you need to make two circles of the same diameter. If you need to make a classic frame for a lamp, then in it the lower circle should be of a larger diameter than the upper one.

round shape can be obtained if the partitions are not straight, but slightly curved. The classic frame will only benefit from this.

The shape of the frame will be interesting if there is a ring at the base and not at the top. It turns out that the concave partitions will be connected at the top at one point, and at the bottom they will be fixed at the same distance from each other.

Best for making frames wire, since it can ideally keep its shape, besides, it is non-flammable. Suitable for work copper, aluminum or steel wire with a diameter of 2 mm.

DIY lamp types

I really want to update not only the furniture, but also the accessories after the repair in the room. These include lamps, chandeliers, floor lamps and table lamps. It is desirable that such a piece of furniture be an exclusive detail; it can be installed in the room on coffee table or in the bedroom bedside table or on a chest of drawers.

To get an exclusive chandelier model, you need to visit exhibitions of handicrafts. If the model you like is worth a lot of money, then you should not be upset. You just need to use your imagination, “turn on” your hands and head - then you can make an exclusive model with your own hands. Since a chandelier usually has not one, but several identical shades, it will take more time to make them than for one.

Modern lampshades can have the most different shape, decorate them to your liking. Preference is given to products decorated with colored beads.

If you want to update your table lamp shade, then ideal option will be cardboard. It must be strong, but thin, then the product will be completely different from others. The work is performed in the following sequence:

From cardboard you need to cut 4 identical frames, similar to those into which photos are inserted.
A piece of fabric must be glued to the back of each product.
In each product, on the side, you need to make holes at the same distance. For this, a needle or awl is suitable. With the help of laces, the parts are sewn together, and a flashlight is obtained.

This method of creating a new lampshade is considered the simplest, in addition, the product is very light. Depending on the situation in the room, the color of the fabric with cardboard is also selected. The decor of such a product can be anything.

Thread lampshade

A ball made of threads looks very impressive in the interior. To make it, you will need patience and perseverance, and besides them:

thread or twine;
round inflatable ball;
PVA glue;
scissors.

The desktop should be covered with oilcloth or unnecessary newspapers, and only after that start work.

The balloon must be inflated and tied with a thread.
We wrap the ball with the selected thread. You can try to make different patterns, or you can just wind the thread around the ball without changing direction.
The winding must be tight.
Having reached the desired density, the thread can be cut.
Carefully impregnate the entire winding with glue. The better the thread is saturated with glue, the stronger the lampshade will turn out after drying.
When the glue is completely dry, the ball can be pierced with a needle and pulled out. Where the tail of the ball was, you need to cut a hole for the cartridge.

If, for some reason, you do not like the color of the resulting product, it can be repainted using spray paint.

The finished twine lampshade can be varnished, decorate with beads or beads.

Paper lampshade

So that the paper cannot heat up and catch fire when the light is on, the lampshade should be quite large. Under such a lampshade, it is better to buy an economical light bulb that heats up less.

Many ideas for making a paper lampshade for a floor lamp can be found on the Internet. Are used various colors, different figures are cut out. The result is a unique creation that can decorate any room.

DIY fabric lampshade

For work you will need:

piece of new fabric;
scissors;
tape measure or centimeter;
thread and needle;
pins;
textile glue or stapler.

Next, you need to select an object for restoration: it may be an old table lamp or any other lamp that has been “living” with my grandmother for a long time. Think in detail about its appearance, which should fit the already created interior of the room.

For example, you can make a new lampshade for a lamp from tissue to cell. It is sewn on a frame of a certain size. If old lamp there is a frame - then, consider that half the work has already been done. And if the frame of the lamp is missing, then this is not a disaster - you can do it yourself, there is nothing complicated about it. Checkered fabric lampshade is ideal for country style.

How to make a lampshade for a floor lamp? A master class on its manufacture can be found on the Internet.

To sew a lampshade onto a cylinder-shaped frame, you need to measure its circumference and height. On the fabric, make a pattern according to the dimensions obtained, then cut it out like a template.

For the cone, you need to make a blank from whatman paper. Try on what was cut out, cut off everything superfluous. If something doesn't work out, you need to redo it.

The fabric for the lampshade is attached to the cone, and the pattern or ornament must be placed correctly. To make the surface smooth, the fabric must be stretched.

The fabric for the lampshade can be cotton or linen.

Lamp shade for children's room

When the child is small, the lamp in the nursery is very relevant. You can always buy such a product, but to make it, you need not only time, but also imagination. It is advisable to make a lampshade for a lamp together with a child in order to develop his imagination. Since the ceiling will stand in the children's room, you need to completely trust the taste of the child.

Naturally, the child will want to see his favorite cartoon characters on the night light. You will need to work hard, and cut them out of paper with him or buy ready-made translations. You need to use the idea with a print on cotton.

For the bedroom

If the bedroom is purely feminine, then the ideal option for a lampshade would be a model, tied with thread. The proposed version is crocheted of white threads of the iris type, which are used to knit napkins to decorate shelves or tables. You can pick up a pattern for thin knitting needles, if it makes it easier for you.

For a classic frame, a napkin is not knitted from 3 air loops. The length of the chain should be slightly longer than the top ring of the frame. Further, the lampshade is knitted in a circle, according to the scheme, like a napkin. It is possible that the height of the product will be greater than the length of the napkin, then it will be necessary to knit more in several rows.

The finished product must be washed and be sure to starch so that after drying it has a certain shape.

White knitted lampshade can decorate with colored beads or colored ribbons- It all depends on your imagination.

In a creative experiment, the main thing is to choose the right shade of small decor elements. When the style, color scheme and shape are correctly chosen, then even the most simple thing handmade will look exquisite.

To make a lampshade made by yourself look neater and more beautiful, you need to first paint a new frame made of thick wire, and then carefully wrap it with cotton tape. Then the fabric of the sewn lampshade will not suffer.

Conclusion

It is very easy to update the lamp, the lampshade of which, over time, has lost its original view. After reviewing the relevant information and purchasing all necessary materials, can be done unique thing that will decorate the interior of your home.

Categories

Popular