Thinking about how unusual to finish exclusive log houses, pay attention to the floor from saw cuts. This is not a new solution; even in ancient times, such a floor adorned both the rich houses of merchants and the small shacks of the poor.

Today, the masters have returned to such a finish, saw cuts natural wood used to decorate floors and walls, to create decor and "paving" paths in the garden.

The advantages of decorating the floor with saw cuts of wood:

• Environmental friendliness;
• Savings on additional finishing materials;
• High strength;
• Aesthetics;
• Ease of creation.

Disadvantages of decorating the floor with saw cuts of wood:

• Large consumption of high-quality wood;
• Preventive inspection of the coating every two years.

Choice of wood

For finishing the floor, you can choose any type of wood, but it is desirable to avoid the use of species with a dense texture. These are beech, walnut, hornbeam and oak.

All wooden logs must be well dried, wet material cannot be applied.

It is necessary to dry the blanks in natural conditions: in dry weather in the open air. During precipitation, the tree is covered with polyethylene.

Technologies for finishing the floor with saw cuts of wood

There are several methods, each of which can be used when decorating exclusive log houses.

Method #1

Need end saw cuts of logs up to 12 cm thick. Saws allowed different size which will make the floor even more unusual and original. But work with blanks different diameter more difficult.

Stacked trim like a mosaic or paving slabs, making small gaps between the elements (1-1.5 cm). Before installation, an embankment (up to 10 cm) of sand and fine gravel is made on the base. Sometimes liquid cement is used instead of a sand and gravel embankment.

Mount wooden "ovals" so so that they are slightly pressed into the sand. During installation, it is important to control the height of the “flooring” with the help of a level - it must be even. To level the surface, use a wooden or rubber mallet. Knock on wood carefully so that cracks do not appear.

The gaps between the cuts are filled with a mixture consisting of:

• melted lard or animal fat;
• sawdust;
• lime;
• moistened clay.

Close up the seams very carefully and left to dry for a few days. The paste is injected into the seam and rubbed well so that there are no voids filled with air. The presence of "air pockets" leads to cracking due to the ingress of moisture.

The same composition close up the cracks in themselves wooden blanks. After the joints have dried, check the surface for the absence of new cracks. If cracking appears, the defects are again filled with the composition and allowed to dry for several days.

After polymerization paste floors are cycled with a machine, before that it is advisable to scrape out the remains of the mixture from the seams. After grinding is completed, they are checked again for cracks, if new defects appear, this place is filled with paste and, after drying, it is polished by hand.

How to prepare a mixture for filling gaps

We indicate the proportions for processing one square meter of surface. You need a 3-liter container (not metal or plastic, ideally glass). 0.2 kg of melted lard, 0.2 kg of lime, 1 kg of sawdust, 0.4 kg of soaked clay are placed in a container.

Ingredients thoroughly mixed, after which a paste-like consistency is obtained. To obtain a moisture-resistant “grout”, marble dust can be added to the paste.

Method #2

Logs are sawn on workpieces of the same thickness using a band saw. After that, the blanks are glued with building glue on a flat plywood or chipboard base. The gaps between the "ovals" are filled with a solution in which at least 1/5 sawdust.

After drying the surface is polished until flat surface. After grinding, the wood is covered with a sealant.

Finishing

After all the procedures, the floor is given another day to dry and proceed to polishing. For a natural floor, it would be logical to use it as finishing natural materials. Most often it is beeswax and linseed oil.

In demand and clear varnish. If desired, transparent cash floors based on polyurethane can be used, but this solution impairs the environmental performance of the finish. Covering paints can also be used, but the expediency of such a decision is doubtful, because all the beauty will be hidden.

Exclusive log houses with such an unusual floor will look very impressive! But sometimes owners are scared off by the price - only high-quality wood is needed! And you always have to pay more for quality than for consumer goods!

Before installing the floor, make sure that the wood saw cuts are well dried.

Materials:
Pieces of logs are about 10-12 cm thick (the diameter may differ from everyone's imagination).
Sawdust, limestone, clay, linseed oil, beeswax, water, lard.

Floor installation is similar to laying paving slabs.
Stages of work:
1) Prepare the floor. We fill it with river pebbles by about 7-8 cm.

3) When laying the saw cuts of a tree, we tap with a hammer and check with a level so that the floor is even. The distance between saw cuts should be from one to two centimeters.

4) We make a mixture for filling the joints: For a floor area of ​​​​about 5 square meters in a 15-liter bucket for 1 kg of melted pork fat, add 1 kg of lime, 5 kg of sawdust and 2 kg of clay with water. This mixture must be thoroughly mixed. You should get a pasty mass. You can also add marble dust to this mixture to make the mixture waterproof.

5) Rub the prepared mixture between saw cuts. We try to rub it in thoroughly so that no air remains inside, as cracks may occur later.

6) Leave the floor to dry for one or two days. After drying, we check if cracks appear, then cover them up and wait for complete drying again.

7) After complete drying, the floor must be leveled so that the surface is smooth (you can rent a scraping machine). Again, check the floor for cracks and chips. If they are, then cover them up.

8) We polish the floor. Since our floor is made of natural materials, we will polish it - beeswax and linseed oil. This will make the floor waterproof. If desired, you can cover the floor with various stains and varnishes, but these are all chemical compounds.

All buildings and structures (gazebo, terrace, swimming pool, greenhouse, vegetable garden and different elements landscape design) at the dacha or personal plot communicated through tracks.

What kind of path to make, or rather, from what material, everyone decides for himself, specifically within the framework of this article, we will consider the manufacture of a garden path from chopped tree rings.

Among all the options (from boards, timber, shields, garden parquet, branches and bamboo), one of the most accessible in terms of material and the most difficult in terms of device is the path from tree cuts. The material is structured according to the principle step by step instructions so that anyone can build such a path with their own hands.

Track from wooden cuts can be called differently: from slices, stumps (dice, block, stump, log, ends of logs), but the method of construction will be identical.

Garden paths from saw cut wood - step by step guide

For work you will need materials and tools:

1. Saw cuts (cuts) of a tree
2. Roll waterproofing or geotextile (geotextile)
3. Sand, pebbles, gravel, water
4. Level
5. Hammer (preferably a mallet)
6. Chainsaw manual
7. Shovel, buckets, brushes

Step 1 - preparation of wooden saw cuts

You need to start working with pre-training saw cuts (cuts) of a tree. Then they will be ready just in time for laying.

When choosing wood, you need to proceed from how long it is supposed to operate the track, and what load it will have. When arranging garden paths from tree cuts in the country, it is better to give preference to hardwoods. So, for example, oak will serve you for about ten years, pine - no more than seven. And larch is practically indestructible and will delight you for more than a quarter of a century.

But, most often, blanks for the track are made from those rocks that are available. It all depends on the budget, saw cuts from poplar will cost much less than from oak or larch.

To prepare the cut, you need to dissolve the log into pieces 150-200 mm high.

The rule works here, the larger the diameter of the log, the greater the saw cut height should be. And of course, the height of all blanks should be approximately the same.

If the thickness of the saw cut is less than 100 mm, there is a high probability that it will not be fixed in the ground, and may “pop out” when pressed.

To extend the life of the saw cut, it must be cleaned of bark. Because it is the bark that will begin to flake off first.

In addition, it is better to refuse to use saw cuts that have cracks. They will begin to deteriorate first of all and very quickly, and the crack may increase under the influence of loads on it.

The saw cut must also be pre-processed. The most common can be called drying oil treatment.

To do this, it is heated to a boiling state and the saw cut is completely coated. Please note that this work is dangerous, so it is better to buy special antiseptic solutions that will provide both moisture protection and biosecurity. In such a solution, the saw cut should be from two hours to two days.

To protect the wood from decay even more reliably, the bottom of the round timber must be additionally treated with bitumen. Wood can be aged with a solution of copper sulphate.

The treated saw cut must be dried well.

Step 2 - marking the track

The complexity of this step is in determining optimal sizes paths - 350 mm, sufficient width for one person to move freely. As well as its route - to provide access to all the required objects.

Step 3 - ground preparation

In order for wooden garden paths to serve you as long as possible and be safe, they must be securely fixed.

To do this, along the marked route of the future path, you need to dig a trench. Its depth depends on the length of the hemp (cut) plus 50-100 mm. (depending on the type of soil and the expected load on the track).

The width of the trench is equal to the desired width of the path.

A waterproofing film is laid on the bottom of the trench (you can apply polyethylene film used for greenhouses or geofabric).

Gravel or small gravel is poured over the film. This drainage is necessary in order to protect the wood from moisture. The height of the first layer of the cushion is half of the required height (25-50 mm). It is important to pack it well.

The sand and gravel cushion must be leveled using building level. This will significantly save time and effort when laying saw cuts.

Step 4 - installation of curbs for tracks (sides)

If a curb is provided, then they must be installed before the installation of saw cuts.

Stones, bricks, sheet iron, wooden bars or long logs.

But, in order not to disturb the harmony of the garden path, chibouks sawn along are used.

Step 5 - filling the second layer of sand cushion

Sand is used as the second layer. The total height of the pillow is 50-100 mm.

To compact the sand well, a technique such as watering it with water is used.

The material was prepared for the site www.site

Step 6 - scheme for laying saw cuts from wood

The order in which the wood slices are mounted is not critical. The formation of the pattern depends on the preferences of the owner.

It can be positioned so that there is as little space as possible between the cuts. And you can, on the contrary, arrange them widely.

The main thing at this stage is to slightly “drown” the saw cut (tamp it down), and also align them in level.

Step 7 - decorative design of a garden path from tree cuts

The space between the cuts can be covered with sand or earth mixed with seeds of ground cover plants.

And leave the cuts themselves in their original form or paint with bright colors.

You can more clearly show how to make paths from tree cuts using a sectional drawing of a path.

Caring for wooden walkways

So that a do-it-yourself garden path made of saw cuts of a tree does not lose its original view She needs constant care.

To do this, once a year you need to clean the cuts with a metal scraper, treat with an antiseptic and apply a special protective coating, drying oil or paint.

Advice
When you make a track, set aside a few cuts in reserve, in the future, it will be possible to replace individual elements during the repair process. In order to reduce the sliding effect after rain, do not polish the ends of the logs heavily before installation.

If you are interested in the process of arranging a path from tree cuts - a video illustrating DIY manufacturing

Garden paths from saw cuts of a tree - arguments "for"

• cheapness;
• high speed and ease of arrangement;
• the ability to carry out the entire process independently;
• do not accumulate moisture (do not create puddles);
• have a natural appearance;
• very maintainable;
• environmentally friendly;
• opportunity to make a unique garden path from wood. After all, all saw cuts are different, which means that it is impossible to repeat the pattern;
• the ability to use end-of-life logs as mulch or chop and add to compost.

Country paths from saw cuts of a tree - arguments "against"

• subject to decay;
• react to temperature changes;
• require constant care;
• become how many after the rain (leveled by using a special composition for processing).

Conclusion

Based on the foregoing, it becomes clear how to make a path from tree cuts with your own hands, without resorting to excessive costs and outside help. Although, you should not rely too much on cheapness, even with self-production you will have to spend money, but such a path is worth it

How to make a floor from wooden cuts?

So, further it will be written how to make a floor from wooden cuts, what are their advantages. Recently, tree cuts have become very popular. They are used for interior decoration, they are made various items, they are also used to make floors in the house.

To make floors from saw cuts, a lot of work is not required. The result will delight with the natural expressiveness of the texture.

Today it is very fashionable to use natural materials for decorating rooms. Next, it will be described in detail how to make a floor from wooden saw cuts in a house.

Advantages and disadvantages of sawn flooring

First, more about the advantages of this method of decorating floors:

1. The floor will be made of natural material, which will not have any negative consequences for human health;
2. Due to the fact that it is made of natural materials, this will save money;
3. The strength of the floor exceeds all expectations;
4. Such floors will have an aesthetic appearance and a pleasant surface for the feet;
5. To make a floor from wood cuts, you do not need to hire specialists, which also saves money.

Now a few shortcomings:

1. For this floor you will need a large number of wood High Quality. For this reason, it is desirable to cover small areas in order to protect the forest;
2. Sawn floors will require regular Maintenance. This must be done every 2 years;
3. To perform such floors, any tree species can be suitable. But it is recommended to choose wood that has a dense structure. Oak, walnut, hornbeam, beech have such a structure.

To perform work, the wood must be completely dried. Wet wood is not suitable for the floor.

Option one

For this option of making the floor with your own hands, end log cabins of logs up to 120 mm thick can fit. However, in this situation, you can show your imagination and lay round log cabins of various diameters. The following materials will also be needed to complete the work: lime, sawdust, wax, clay, flax oil, water.

Laying is done as for a mosaic with small gaps between adjacent parts. Sand with small pebbles up to 10 cm thick should be poured onto the surface. Then saw cuts should be laid, pressing them into the sand a little. You also need to adjust the height of the parts - it should be the same. Gaps should be filled with the following paste: 1 kg of fat, 5 kg of sawdust, 1 kg of lime, 2 kg of moistened length.

Then you need to carefully fill in all the gaps and cracks in the cuts of the tree. Leave everything to dry for 2 days. Then the surface must be well polished. You can do this with wax and oil.

Option two

Wood cuts need to be cut band saw. Then they are placed on plywood, glued with glue for construction works. Seams to be filled special solution, in which there should be 20% sawdust.

When everything is dry, you need to sand it with a sanding machine. The surface of the floor will become even, and the cuts will be clean. Then the surface of the floor from the cuts must be covered with a sealant. Mortar 80% is a self-leveling epoxy-based self-levelling mortar. The color is recommended to choose dark. But it will be necessary to watch that the dark paint does not stain the surface of the log cabins.

In some cases, saw cuts are placed on liquid concrete. However, the choice of material is at the discretion of everyone.

After final alignment and polishing, the floor surface can be covered with a stain, then apply a finishing lacquer coating. So the floor can be given a certain shade.

Now we know about the implementation of the floor of wooden log cabins. Here you can give freedom to your imagination and make various ornaments from log cabins of different diameters. Follow our instructions on the technology of work and the saw cut floor will be excellent. We wish you success!

More articles on this topic:

Using wood oil

What are the wood impregnations for internal works: reviews and recommendations

Types of paints for wood and their features

Do-it-yourself wood cut floor: its features and do-it-yourself installation

The statement that it is not difficult to make a floor from saw cuts with your own hands, to put it mildly, is not entirely true - despite the fact that technologically such decorative coating looks simple, in fact it is replete with a mass of various subtleties and nuances.

If you treat such a floor with disdain and underestimate the complexity of its manufacture, the result is depressing - several years, and the coating will have to be redone. Do you need this? To do, to do so - at least such a floor should leave for a dozen years. And at least its dismantling at the end of its service life should not entail a global, large-scale repair - ideally, it should look like, for example, replacing linoleum or laminate. I agree that it is very difficult to create such a coating with your own hands, but you need to strive for this - in principle, it is real, and we will tell you about how to make such a floor from wood cuts with your own hands on this page of the Dream House website. But first, let's look at the advantages and disadvantages of such floor covering.

Floor from wooden saw cuts photo

Advantages and disadvantages of a do-it-yourself wood cut floor

Agree, almost all construction and Decoration Materials, which today a person uses to equip his living space, are mostly of artificial origin. Even if they are not toxic and are classified as environmentally clean materials However, they do not have a natural origin, and from the point of view of Feng Shui science, their energy component tends to zero. But this is not the point - unlike them, wood (including its cuts) is a creation of nature, which is the first advantage of the floor from saw cuts. Do not rejoice in advance - this is a double-edged sword. On the one hand, natural wood, and on the other, synthetic polymer binders, which will have to be used as protective coating- in general, the situation from an environmental point of view is twofold and, most likely, negative factors here they will win and nullify the entire ecological component of the floor.

By by and large, here you can highlight only a few advantages that can really be called the advantages of such a floor. Oddly enough, but this is a decorative component - in fact, it is a mosaic. which you can do at your discretion, creating various patterns. And save money by doing the installation work yourself. In my opinion, everything else is far-fetched. Judge for yourself.

1. Saw cuts are natural and cheap, and sometimes even free material. I agree, you can cut thin sections yourself - having the same power saw on hand is not a problem, even if you use thick branches brought from the nearest undergrowth or planting as raw materials. But look further - to bundle all these stumps into a single floor from saw cuts, nothing more than an epoxy or polyurethane self-leveling floor is used. which today is considered almost the most expensive coating, which, by the way, will need much more than to create a decorative 3d floor. You can talk about the cheapness of the floor from saw cuts only in the case of installation, so to speak, folk methods(a bunch of clay with sawdust), which are by no means durable.
2. High floor strength. The situation is the same as with cheap raw materials for such coatings. The strength of this floor is due to three factors - the presence of a rigid base under the cuts of the tree, the strength of the wood itself and the strength of the protective coating. It's no secret that high-quality and durable wood, such as oak, hornbeam, beech, to put it mildly, does not roll underfoot, and the one that rolls requires additional processing, i.e. preparation. In principle, and this is not a problem, such a nuance simply increases the duration of the installation work.

Floor from saw cuts photo

But back to our strength - a good and durable floor from wood cuts cannot be made cheaply. Spending money in the short term is also a very dubious undertaking. Basically nothing but unusual beauty, such gender cannot be offered to a person. This is solely my opinion, but if you think carefully about this issue, you will surely come to exactly the same conclusion. In the meantime, we will go ahead and tell you about two ways to make a floor from saw cuts with your own hands.

Wooden saw cut floor: an option for giving

Why for a summer residence? The reason is simple. This is a simplified version that does not involve the use of polymer binders. Such a floor can really be called environmentally friendly, and it will cost you the minimum. Along with this, the floor will lose strength, aesthetics and other characteristics. In addition, it cannot be washed in literally words, as unprotected wood will quickly rot. Such a floor is made from saw cuts in a very primitive way.

1. To begin with, we make a blank in the form of thin slices of wood - their thickness should be about 40-60 mm.
2. Next, prepare the base. We make waterproofing in the form of a film laid either on the ground or on the base that is in the house, and pour a layer of sand in order to be able to align the sections in one plane.
3. And then the principle of laying paving slabs comes into play - we drive the sections with a rubber mallet into the sand, tightly fitting them to each other, and setting them with the help of a level into a single horizon plane.
4. At the final stage, when all the sections are laid, the seams are sealed, and at the same time the floor fragments are fastened. For this, a kind of original paste is used, in which wet clay, lime and sawdust, formed during the sawing of logs, are mixed. This paste must be literally pressed into the empty space between the slices - so that it goes along their entire height.

Floor from end cuts photo

When everything is dry, the floor will need to be sanded. In order for such a miracle coating to last longer, each section must be thoroughly soaked with an antiseptic. In addition, before laying the wood must be properly dried.

End-saw floors: durable technology

As in the previous case, all wood used for the manufacture of such floors must be well dried and treated with an antiseptic. To achieve various effects, it can be tinted with a stain. An important condition creating such a floor is to strictly observe the thickness of the cut - if in the first case this moment of great importance does not, then here differences of 1 mm will result in a large consumption of polymers, which will make the floor very expensive.

In this regard, it is better to think over a device that will allow you to make saw cuts with maximum accuracy. In addition, they also need to be made as thin as possible.

Such floors are made from saw cuts with their own hands as follows.

1. Foundation preparation. It must be made even and clean - ideal option will use self-leveling compounds.
2. Gluing cuts. A polyurethane or epoxy self-leveling floor is used for this - a concrete or wooden base coated with this compound will not only allow you to glue the sections, but also create a kind of waterproofing layer. Therefore, it must be applied without sparing, continuous over the entire surface. Naturally, in parts, so as not to trample and pollute the floor.

Do-it-yourself saw cut floor photo

Now such seemingly very simple at first glance floorings from wooden sections of logs have become very popular - such peculiar stumps. They are used as decorative elements, items for various arts, as well as for larger projects, such as paving paths in the garden and at their summer cottage, finishing all or part of the walls of the premises.

Some craftsmen have long tried to make a floor from wood cuts with their own hands for their own summer house or even an apartment.

They argue that the work is not at all as complicated as it might seem, but the result is striking in the natural expressiveness of texture and pattern.

Almost all the materials that surround us in a modern house may be beautiful and comfortable, but, to be honest, they are artificial, not always environmentally friendly, and sometimes even toxic. In our time, it has become very fashionable to use more natural materials, in particular wood, both in decorating the room, crafts, furniture, and in the manufacture of complete walls, floors, ceilings, even paths in the garden and in the garden.

As you know, everything new is a well-forgotten old. End cuts have been used in home and garden decor for a long time. Both in rich houses and in simple village ones.

They were laid in outbuildings, forges, on the streets, in houses in the form of parquet, but not the one that we know now, but the end. It was made in the large halls of palaces, from a variety of wood species, even interspersed with soft species, it looked excellent.

Do-it-yourself wooden floors from saw cuts

The advantage of saw cut floors is "naturalness", as well as low cost. The floors are very strong and hard, durable, have an excellent appearance. Make sure you can do it yourself. They are warm, well accumulate and retain heat from the battery, stove and just sunlight from the window.

This is a durable material, especially if you use special tools. For example, there are impregnations for protecting and preserving wood.

Real wood parquet will never go out of style. Today we will think about the production of a floor from wood cuts, radial or transverse cuts, otherwise they are also called end cuts.

The idea to make an original wooden floor with your own hands is in the air. As far as I know, there is far more than one option for implementing this idea.

I made a selection of photos, as well as information on one topic - saw cut logs as a "floor covering". Maybe someone will be inspired by this idea and make an exclusive floor from wood cuts for their house with their own hands.

You will never get tired of looking at such beauty - the structure of the tree on each cut is so unique, it is a drawing of nature itself.

As you can see in the photo, cracked logs will also be used for work and what is called “non-standard” - tree trunks that are not quite round in cross section. In the intervals between the large ones, small ones will lie well - saw cuts of small branches and twigs.

Someone decides to use round saw cuts (“round saws”) for themselves, some even take them with bark, while it must be understood that there is a problem of filling empty areas between wooden circles and attaching them to the floor. This floor looks very decorative.

You can make saw cuts yourself, many in summer cottages have such an opportunity, and you can also buy them, now such blanks are very popular, in particular for the manufacture of various crafts and interior decor.

Some people want to get around this problem by using wooden blocks of strictly geometric shapes - for example, squares, diamonds, hexagons in the form of "honeycombs", while the parts will fit together with little or no voids. But there is more work to process the source material, and it will take a lot of it.

In this age of new technologies, some have found a solution. Everyone knows self-leveling floors, which were first made in industrial premises, as well as in wet ones. Now there are lovers who have such a floor at home, it is good for the bathroom or kitchen, it does not require special care.

Its advantage is that under a transparent bulk coating you can place a drawing, a collage with some interesting objects, I even saw floors with small coins along the entire length. I don’t know how much money it attracts, but there is undoubtedly a decorative element in such a floor.

Wooden saw cuts - laying and pouring technology

Now let's talk about the most interesting - the actual technology. Almost any tree species is suitable for work, but it is better if these are plants with a dense solid structure. As we know, for example, oak, beech, hornbeam have solid wood.

In addition to hardness for wood, there is also the concept of stability, this is also important for what we are going to do. We do not take into account exotic species, and if we consider traditional species, then these two indicators are at their best in oak and walnut.

Trees such as linden, spruce, poplar, pine, aspen, cedar, fir have soft wood, they are not suitable for the production of floors. There is a measure of wood hardness, it is measured according to a certain Brinell scale. So, for the manufacture of parquet, only those trees are used that have at least an average hardness according to this very Brinell scale.

I think that it is clear that the saw cuts should be very well dried. No humidity is allowed.

Method 1

Here is a description of one technology. End cuts of logs 10-12 cm thick will do, but it's a matter of fantasy, you can take absolutely any, lay circles of different diameters in one floor. Lime, sawdust, wax, clay, linseed oil, lard, water will also be needed.

Laying as for a mosaic, with minimal distances between adjacent elements. Sand with small pebbles is poured on the surface with a layer of up to 10 centimeters. After that, the saw cuts are laid, pressing them into the sand, making sure that the upper level is approximately the same for everyone.

How to fill the space between the round logs_ “Holes” are filled with a composition according to the consistency of the paste: 1 kilogram of fat, 5 kg of sawdust, 1 kg of lime, and about 2 kg of wet clay. They say that it is not bad to add marble dust or small glass fragments to the composition.

Carefully fill all the voids, as well as cracks in the cuts, allow to dry for 2 days. After that, the surface should be well polished, a scraping machine will not hurt. Polished with wax and oil.

Method 2

Here is another description of the process. Sawing wood cuts with a band saw. Lay them on plywood, gluing them with building glue. Fill the seams with a specially prepared solution, in which 20% sawdust. After hardening, it is polished with a machine, while the floor surface becomes even and the cuts are clean.

From above, the floor with cuts is covered with sealant. I think 80 percent of the grout is an epoxy based self leveling grout. It is better to take a dark color, but then make sure that the dark color does not stain the surface of the wood.

I think, at the end, you can apply a topcoat, varnish, epoxy, polyurethane-based self-leveling floor.

By the way, some put saw cuts on liquid concrete, probably for greater reliability, as in the very first photo. So here everyone decides for himself what it will be more convenient for him to work with.

By the way, if you want the woody visible surface of the floor to have a certain shade, then this can be done, for example, with a stain, immediately after leveling and grinding, before applying the final varnish coating.

In interior design nowadays, saw cuts are widely used to create very beautiful countertops, chairs, decorative wooden wall panels in eco style. Remember the cartoon about the hedgehog in the fog? There, the hedgehog talks about juniper twigs. Crafts or artistic compositions from juniper are better not to be covered with anything on top, with no varnish - they have an amazing aroma that lasts for many years.

A saw cut of a tree is an interesting material for creating all kinds of crafts, and it is beautiful in itself. Children enjoy burning and drawing on them.

What else I would like to add is that the end parquet made of transverse rounds does not have to consist of round mosaic components.

If you have a beam, square or rectangular in cross section, it will also be interesting, only there is a certain specificity here - the gaps between the parts will be smaller. Looks like real parquet. However, this is parquet, only made using a different technology.

Mosaic on the floor with examples of geometric elements of the pattern

The floors are different, wooden saw cuts are also a kind of “mosaic”, since they are laid according to the same principle. But then we'll talk about the classics. Simple as well as more complex patterns and ornaments with two, three, four color combinations of tiles. Samples photographed in the museum, these are the work of old masters.

Unusual furniture, also made by hand, on your own, is best suited to such unique wooden floors. It will perfectly complement the interior. If you follow the link (a large selection of different options), then there, in addition to those in the picture, you will also see several examples of tabletops for tables with sawn wood.