How to glue wallpaper to plastic. Wallpaper and decorative panels: decoration and combination in the interior Is it possible to paste wallpaper on MDF

Still, it’s worth starting with one small but fundamental question: pasting or wallpapering, how to write? Everything here is simple, make no mistake - wallpapering (that is, wallpapering) or wallpapering the walls of the house (that is, you are pasting the walls). So wallpapering will mean that you are pasting them with something, and wallpapering is also not the right expression. Immediately it is worth making a reservation - a wallpaper sticker on what. But, of course, not these rules will be dealt with in the next review. Main question how to paste the wallpaper so that there are no bubbles, so that the pattern converges, so that they do not peel off, finally.

There are situations in life when wallpaper in an apartment or house needs to be glued quickly. And if a professional and his services are not available to you, you will have to glue it yourself, it is not so easy, but some recommendations may help you.

How to paste wallpaper quickly:

You need to paste over the room from the corner that is closer to the window;
The strips must be glued strictly vertically, and a plumb line is used;
An additional segment that exceeds the height of the room is 10 cm on the floor, and 10 cm on the ceiling (then cut off the excess);
Do not unfold the bottom of the wallpaper strip until the top has been smoothed out with a roller;
To stick the strip parallel to the doorway, you need to measure the distance from the edge of the wallpaper to the door;
The top layer of wallpaper, superfluous, is cut off with a clerical knife.

If the canvases are glued to corner area, one strip should not protrude on the other wall by more than 6 cm. Cut off all excess before spreading with glue.

Wallpapering quickly and efficiently (video)

Wallpapering tool

Which tool to take, it is impossible to say unambiguously. Someone manages with a minimum, for someone the list with ten names will be small. The master also will not give a universal recipe, everyone works to the extent of their convenience. What one needs, another will interfere, and the repair will be delayed. But you can list the entire tool, which, in principle, is used when wallpapering walls is in progress.

What tool will you need:

Carpenter's pencil (for precise marking);
Stationery knife (it is more convenient for them than to cut strips and cut off excess with scissors);
Metal ruler for marking;
Scissors for trimming;
Square (if there is a need to build a perpendicular;
A plumb line to mark a straight vertical line;
Level to check the verticality of the paintings;
Paint roller;
Brush or roller to smooth the streaks;
Glue mixer;
A paint spatula to trim the strips at the joints;
Wallpaper spatula to smooth the stripes on the surface;
Wallpaper roller that smoothes thin wallpaper;
Roller to smooth the joints;
Container for stirring glue;
Basin to use clean water;
Sponge;
Rags;
Upholstery cord;
Ladder.

And, by the way, this list is incomplete, there are special tool, there is also a tool, let's say, home-made, which a person adapted just in order to paste wallpaper.

We prepare a tool for pasting walls with wallpaper (video)

Wallpapering: answers to all questions

There are at least a dozen and a half questions that become important both before and after gluing, especially if there were any failures. So, so that neither before nor after there is excitement and annoyance, you can wind the information from the following list on your mustache.

The most popular questions about wallpapering:

How to glue one wallpaper. For beginners, the option is dubious, but if you have already got the hang of it, then not very big room this is real. You can buy more expensive wallpapers that do not need to be smeared with glue (only the wall). Or make cheat sheets with instructions on what to do and after what, how to properly paste wallpaper in the corners and around windows.
Is it possible for pregnant women to glue wallpaper. No one will ban it, but what is not desirable is for sure. And it's not just the materials, the so-called "chemistry", the process is tedious, long. Often you have to stand with your hands raised high, and women in a great position are not advised to do this, especially in the later stages.
How to glue wallpaper with a pattern. In fact, the technology is fundamentally different from conventional gluing. Unless there are the following nuances: you can combine the pattern when gluing the first canvas, when the second is applied and marks are made so that the fit is according to the markup. If the measurements are already on the wall, then you can reduce the drawing on the floor, which many successfully do before sticking the canvas to the wall.
How to glue wallpaper on concrete walls . Most often, concrete walls are puttyed and primed, after which we can only talk about gluing. Sometimes, in order for concrete walls to become even, they are also plastered. Experts advise doing the primer in two layers in order to level the concrete walls to perfect evenness. For a primer, a liquid primer is applied to concrete walls. adhesive solution, after the first layer follows the second, thicker. And even after that, draft wallpapers, the same newspapers, are usually glued. And although technology has stepped forward, modern glue has good adhesion, it is not worth wallpapering concrete walls without preparatory work.
How to glue meter wallpaper . This is done according to the same principle as pasting the wall. ordinary wallpaper, do not use only fast drying glue. The easiest way is to paste over the ceiling with meter wallpaper.
Is it possible to glue wallpaper in winter. Wallpaper is "afraid" of sudden temperature changes, and not specifically winter or summer. Drafts are another enemy when wallpapering. Well, one more nuance, which is just the same for winter, if you paste over the walls near the battery, in this area the wallpaper may lag behind.
When is it better to glue wallpaper in winter or summer. Better in summer if the air temperature is not higher than 23 degrees and drops are not predicted.
Is it possible to glue wallpaper on whitewash. The answer is simple - you can, but only if you glue the wallpaper after the preliminary quality primer. acrylic primer will bind a layer of whitewash, so that the wallpaper will take better.
Is it possible to glue wallpaper on plywood. It is possible, but not desirable. The relief of plywood appears through a thin canvas, another nuance is the hygroscopicity of plywood. Under the influence of the level of humidity, it will change, which will also affect the wallpaper.

Little tricks

Here are questions with short answers, after which you usually reject one solution, or make sure another is correct.

Short answers on wallpapering:

Is it possible to paste wallpaper on plastic panels . In principle, yes, but you will need two coats of primer: one for processing PVC materials, after which you will need to apply a layer of a special adhesive primer.
Is it possible to glue tiles on wallpaper. Technically, this is possible, but the masters unanimously say - it’s not worth it, you suffer both in the process and after it, the result may be unaesthetic.
What can be pasted on the wall besides wallpaper. All the same wallpaper, only textile. In fact, these are fabric canvases that will look like wall upholstery with fabric. Well, no one has canceled the good old version - photo wallpaper.
Is it possible to glue wallpaper on fiberglass. Theoretically yes, but with a good primer and glue. But there is little point in such an occupation, the canvas itself can be perfectly puttied and painted.
Is it possible to glue wallpaper on MDF panels. It is possible, having degreased well, cleaned the surface, and primed. The seams can show through the wallpaper, so the primer must be applied in a thick layer.
How to glue wallpaper. Jointed, overlapped, with or without drawing together - it all depends on the type of wallpaper and the type of walls.
At what temperature can wallpaper be glued. The main thing is that it should not be higher than 23 degrees plus, there are no drafts and temperature changes.
Is it possible to glue wallpaper over wallpaper. It is possible and even necessary, you definitely don’t need to peel off all the wallpapers, it’s enough to remove those that are themselves well behind.
Is it possible to glue wallpaper on chipboard. It is possible, without missing such stages as plaster and primer, and sometimes chipboard is glued with gauze.
Is it possible to glue wallpaper on a rotband. It is possible, but again, without putty and a primer, it will not be possible to do this qualitatively.
How to glue wallpaper behind batteries. wide or narrow wallpaper, it doesn’t matter, an even piece of canvas will have to be cut into equal parts, and lay out this mosaic behind the battery.
Is it possible to glue wallpaper horizontally. This, of course, is unusual, and visually cuts the height of the room, but this option is also acceptable. True, think three hundred times, an unusual look and an unsuccessful selection of wallpaper will suggest plywood.
Wallpaper glue. It's better to use the same glue that glued all the wallpaper. It's more expensive to experiment.
Is it possible to glue wallpaper on OSB boards . Yes, you can, and even thin wallpaper.
How to glue wallpaper on baguettes. It’s better not to do this, isn’t it easier to remove the baguettes and stick them on top?
Why glue newspapers under the wallpaper. This habit came from the Soviet era, when both the glue was homemade and the wallpaper was simpler. Today, there is virtually no need for this.
What wallpaper to glue on uneven walls. Any, but the walls still have to be leveled. Otherwise, the result will not please you.
How to glue meter wallpaper for one person. There are only two tips here, buy non-woven wallpaper to spread only the wall, and cut the strips in advance. Well, the tool so that everything is at hand, there is no one to run after it, and distractions are more expensive for yourself.

That, in fact, is all. Although no, there is one more important question, but it is worth considering separately.

What kind of wallpaper to glue a small room

How to glue wallpaper in a small room? The first universal advice- take light-colored obi without a pattern. dark shades, by the way, "steal" up to 40% of the space. White is also not the best option.

Perfect for a small room:

Cream;
Light pink;
Grey-blue;
Greenish blue;
Sand;
Light yellow.

In a dark small room, the wallpaper should be warm. colors, and vice versa. Wallpaper with a relief, even a small one, will visually increase the space. Glitter wallpapers also do a great job.

If you really want a pattern, then let it be horizontal. If you want brightness, then let it be only one wall.

Wallpapering: doing it right (video lesson)

How to paste wallpaper? collect all essential tool, find a patient partner, glue exactly according to the instructions, observing temperature regime and other wishes. And do not rush, in a hurry a person is not so critical of details.

Happy repair!

The main problematics of voluminous and large rooms- this is the need to fill the space of the walls with some content. Additional furniture or interior items are sometimes suitable for this because they absorb space. The best way out in this situation is a combination of facings.

So you disguise bad qualities rooms and turn them into pluses. A fairly popular finish of this type with my own hands- This is a combination of panels and wallpaper.

The combination of wallpaper and panels is considered one of the very famous design techniques.

Particularly popular is the horizontal and vertical alternation of panels with tapestries.

Horizontal or vertical combination of claddings

Horizontal alternation of facings.

Wall decoration with alternating sheer or in horizontal position stripes of wallpaper and panels suitable for any room design.

Plots can be distinguished by alternating plastic, wood, cork planks and different types wallpaper for finishing works. Best of all, strong vinyl or non-woven fabrics with relief are suitable for this.
You can change the stripes of both polar and colors with one shade.
The instruction says ideal width strips must be selected based on the height of the ceiling or the length of the wall.
Often, when work is performed related to the decoration of the corridor with panels and trellises or another room, they are separated from each other by borders, friezes, moldings. They not only hide the connections, but also serve as decorative elements.

Using inserts

In the photo, the reception of the connection of the facings with the help of inserts.

At the very beginning, the walls are prepared.
After they are glued with wallpaper or lined with panels.
Further, on the areas left in advance, the connected cladding is installed.
Inserts can serve as cuts of canvases or strips of various shapes and sizes.
A similar design involves the design of the inserted components with curbs, thin slats or moldings.

Wallpaper inserts on large volumes

This method is optimal for finishing works of various semantic sections of one room, i.e. its separation.

For example, a nursery is divided into sleeping, play and educational areas. Place panels next to the bed and work table instead of wallpaper (calm shades), and glue the playing area with canvases bright color. This kind of semantic load will enable the baby, where necessary, to concentrate or show emotionality and his dynamics.
In the reception room, a wonderful option is to mark a wall or a niche with a TV with contrasting panels or trellises.
AT sleeping area the best thing to note is the headboard. Perfect option to do this is to combine panels and wall planks that have different shades of the same color.

Use of flaps

Patchwork technique of combining different coatings.

This unusual way choose combinations of coatings if you want to make original interior in room.
Here your imagination is not limited, you can cut and paste pieces of panels on the panel different sizes, colors, textures and shapes.
With all this, you can organize the flaps into some patterns or stick them abstractly and chaotically.

Worth paying attention!
It must always be remembered that before sticking tapestries on panels made of plastic, the planks must be finished and primed in advance.
Only then will the materials be consistent with each other.

Emphasis on ledges, niches and structures

When your housing has a complex configuration (ledges, niches, crossbars, etc.), you do not need to consider it a minus of the house. A similar design can be done with a plus. Moreover, the cost of such a change will be small.

You can furnish the complex shape of the room by highlighting original plots from its total volume. So the room will appear in a completely different form. You can sheathe the walls, for example, with planks, and glue the niches with canvases that contrast with them in color.

Wallpapering on panels

Often the question arises when combining facings, is it possible to stick wallpaper on MDF panels or plastic, wood, and other analogues. Let's figure it out.

Analogues from wood processing products

The ISOTEX panels are already covered with trellises or textiles, which can be re-glued if necessary.

Now in many big stores for construction, purchase decorative panels made from wood products, for example Finnish "ISOTEX".

They consist of milled pine needles. Particles of the material are held together due to its pressing at high temperature. In other words, it does not have "chemistry" - resins, glue, etc.
Similar panels have good sound and heat insulation qualities..
Their width is 58 or 60 cm, height 2.7 or 2.55 m, thickness - 12 mm.
Now in production big choice most different colors and invoices.

Worth paying attention!
innovative production technology makes it possible to release light, porous panels, which at the same time have a good density.
This provides the opportunity to stick on similar wallpapers and acoustic panels or textiles.
Moreover, canvases can be used different varieties- paper, vinyl, fiberglass, etc.

How to stick canvases on vinyl planks

PVC panels must be finished with an abrasive washcloth before wallpapering.

Is it possible to stick wallpaper on PVC panels? Yes, it usually can be. But the base must first be sanded and primed.

You will need an abrasive washcloth (Scotch brite), plastic primer, white spirit and adhesive primer.

First matte the plastic cover with scotch brite.
Then remove any dust from it..
Then apply two primer coats for plastic.
Thin the adhesive primer mixture with solvent and coat the panels with it using a paint roller or brush.
When the primer dries out, the question of whether it is possible to stick wallpaper on panels made of plastic will be resolved. Do it courageously.

SIP panels and liquid wallpaper

Wallpaper liquid perfectly fit on the SIP Panel.

Liquid wallpaper is considered a very popular type of cladding. They have good decorative and soundproofing properties.
They perfectly hide small and medium wall irregularities.
Another important thing good quality coating lies in the fact that it can stretch without changing the structure. This property indispensable if the lining is carried out in a brand new house, which did not give the final shrinkage.

It is quite convenient to apply liquid wallpaper on SIP Panels, because. the walls are perfect. If you use them in kitchen area or a room with a bathroom, then cover the cladding with a varnish without color so that it does not absorb moisture, grease and dirt.

Conclusion

Combination different materials considered a very popular type of cladding. This kind of combination increases the possibilities of decorating the premises and makes it possible to hide their bad qualities.

The video in this note will illustrate the topic.

There are two opposing views on this issue. Some of the masters speak of the complete impossibility of carrying out such internal works, the second is the opposite.

The fact is that non-woven, vinyl and paper products It is customary to stick without serious surface preparation. Often this easy cleaning from the old cover. But this happens in the case of walls finished with plaster, which provides the necessary adhesion of materials. If the work is carried out on the basis of wood-based panels (chip and fibrous), then problems arise. First of all, this is the subsequent delamination of the strips in the corners and at the joints. These defects are due to poor preparation surface, it requires much more time and effort.

Indeed, it is not easy to glue wallpaper on fiberboard, chipboard and MDF, but if everything is done in stages and correctly, then the integrity of the coating will be ensured.

When gluing wallpaper on fiberboard, chipboard and MDF, some difficulties may arise

Why do you need putty?

This composition is necessarily used if you want to lay roll products on the walls with high quality. It performs the following functions:

Creating the right grip. In the production of wood-based panels, various resins are used, which ensure the unity of the canvas, but prevent the wallpaper from setting.
Foundation protection. Due to the porosity of the material (especially untreated chipboard), the adhesive is quickly absorbed without creating a binding film, so the application has to be repeated many times. Application of the composition on water based may cause surface deformation.
Coating leveling. For filing vertical structures, panels are not used high class, and puttying allows you to eliminate existing shortcomings (recesses, chips, scratches).

Without preliminary putty, it is impossible to glue wallpaper on a wood base.

Also a significant problem are spots that can appear on the decorative layer due to the presence of resins in the composition of the sheet. They appear even after a significant amount of time has passed and spoil appearance walls.

Technology for gluing roll products

paste over wood boards wallpaper can be done exclusively with your own hands. In order for all procedures to be performed correctly, it is necessary to observe the accuracy and sequence of actions.

Materials and tools

For pasting work, you will need the following materials and fixtures:

Everything you need is purchased in advance. If used tools are used, they are pre-cleaned from previous materials.

Surface preparation

The sticker of rolled products on different panels may vary slightly, so it is necessary to proceed from the specific situation. Preliminary work includes a number of procedures, individual for each species:

General preparatory processes after completion of preliminary work:

The walls are left to dry completely.

On a note! If the vertical structure has a deviation, then it is initially recommended to plaster the surface, and then lay finishing layer putties.

pasting

Work begins with an assessment of the adhesion of putty, for this the surface is slightly tapped. In the absence of delaminations, the process is started:

There is a recommendation that the surface should be varnished. Indeed, it can be done, but to achieve the desired decorative effect it'll be hard. In addition, the face layer will become heavier, which can lead to peeling.

Should know! If the strips are joined end-to-end, then it is advisable to attach a special intermediate tape.

Features of applying liquid wallpaper

Work with this material differs from the previous process by the technology of the last stage. This variety must be laid with a spatula and a grater according to a scheme identical to puttying. To do this, the pre-prepared mixture is evenly distributed over the sections.

Gluing technique liquid wallpaper akin to putting putty on

There is an opinion that when using liquid wallpaper, putty is not needed, but the technology should not be violated.

MDF panels are an excellent decorative finishing material, which is characterized by high speed installation and the absence of the need for "wet" work at all stages of finishing.

They have panels and their drawbacks (for example, MDF, like any wood, is afraid of water and high humidity, is less resistant to mechanical damage compared to synthetic materials, work to restore damage to it is associated with a number of difficulties, etc.).

The fastening of MDF panels depends on the type of base and the desired result. The most common type of fastening is mechanical (on the base, a frame is often equipped with wooden or metal rails, to which MDF panels are attached with nails, self-tapping screws or kleimers) and chemical - using adhesives.

The latter method assumes an even monolithic base, since there is no frame made of profiles or guides in this case.

Glue for MDF - an overview of the best options

The most commonly used adhesives for MDF panels are:

Liquid Nails. Universal adhesive, which is characterized by high adhesion, resistance to corrosion and moisture. Liquid nails do not react with bases, unlike deep-penetrating adhesives.
Mounting (or construction) foam. It is characterized by various properties such as thermal insulation, sound insulation and high adhesion.
General purpose building adhesive. A wide group of products, divided into many segments and areas of application. For MDF panels, it is necessary to use only those adhesives that provide adhesion to the base materials (brick, concrete, drywall, tiles, etc.) and wood (MDF consists of fine sawdust).

The most popular adhesive for MDF panels is liquid nails (TYTAN or TITEBOND Multi).

In addition to the economic effect, when choosing an adhesive, it is necessary to take into account the specifics of working with it (time for primary fixation, final drying time, application method, service life, necessary tools and materials, etc.).

Mounting MDF panels on glue - instructions

Consider the technology of mounting MDF using the adhesive compositions indicated above.

Liquid Nails (similar - universal building adhesives). The thickness of the adhesive layer is only 3-5 mm, so the base on which the panels will be glued must be perfectly even. Otherwise, the panels will repeat all the irregularities of the walls or peel off in places of loose fit.

How to glue MDF to the wall

Therefore, before gluing the MDF panels to the wall, it must be leveled.

Degrease the surface, remove all contaminants, putty crumbling areas.
Before starting work, you need to make sure that there are no irregularities with the help of building rule, long level, or other instrument.
The glue is applied in wave-like movements or in another way (for example, pointwise with large drops) so that it is evenly distributed over the width and length of the panel. The pitch between the adhesive strips determines the force with which the panel will adhere to the base. That is, for example, when installed in places of greatest load, the frequency of application can be increased. Usually this is 10-15 cm. If the manufacturer specifies a waiting time before gluing, the required pause must be maintained.
Using a construction bubble or laser level the launch panel is installed at the desired angle (depending on the intended pattern and mounting direction). Most commonly used vertical installation panels. Start from the corner.
The adhesive on the first panel must have time to grab the base before installing subsequent ones (the same principle applies to other difficult places adjoining, for example, internal or outside corners). The setting time depends on the type of adhesive (see instructions).
Thanks to the tongue-and-groove connection, subsequent panels can be mounted without waiting (except for the waiting time before gluing).

Corners (internal or external), as well as horizontal and vertical junctions without a tongue-and-groove connection, are covered with decorative moldings ( universal angles MDF). Glue should be applied to the middle of each side decorative corner(so that when pressing down, excess glue does not come out).

The main thing is not to damage the decorative layer of the panels.

Option 2. Mounting foam.

The technology of mounting MDF panels using construction foam in many respects similar to the installation technology using liquid nails or universal adhesive, with the only difference that the error of wall irregularities using foam can be higher due to a significant increase in foam volume.

The waiting time before gluing the MDF board to the base depends on the requirements of the foam manufacturer.

Basic installation errors

For liquid nails:

Do not overexpose the adhesive before mounting the panel on the base. Otherwise, adhesion will be significantly lower.
Incorrect application of glue - MDF panels will lose their attractive appearance if glue gets on the decorative front surface.
Wiping off excess adhesive with a highly damp cloth may cause peeling of the decorative coating.

For mounting foam:

For gluing, use foam with a low shrinkage coefficient and professional tool(high-quality guns for construction foam can smoothly and strictly dosed regulate its supply).
If you do not wait for the setting time of the first panel, then during the movement of subsequent panels, the foam may collapse and not be fixed on the base.

Question - why it is impossible to glue MDF on liquid nails

Glue "liquid nails" is distinguished by its versatility. It is suitable for mounting a large number diverse building materials. And if “wood” is listed in the list of materials to be glued, then liquid nails are not only possible, but must also be used for gluing MDF panels.

Often, ordinary people can confuse liquid nails with sealants or silicones (they are applied using the same tool, the tube is very similar to the tube of liquid nails and they can be on the same shelf in the store).

However, sealants for gluing MDF panels are not recommended, since their main purpose is to fix sanitary ware and seal joints.

How to glue MDF - features of installation work
You are interested in the question of how to glue MDF. Consider the technology of mounting MDF using liquid nails and foam.

Go through the joints with sandpaper, then prime them and seal them with putty with gluing the sickle mesh. After that, you need to thoroughly prime the entire area of \u200b\u200bthe MDF wall and you can glue the wallpaper. Why don't you want to dismantle MDF and paste wallpaper on the main wall? What are these unnecessary, extra layers for? There will be a little more work, but the area will increase.

Wallpapering on MDF panels? Are you seriously? Although it's up to you. And if it comes to that, I recommend using it better. for sealing your recesses, hard wax. Or putty on wood, matching in color. In general, sealants are still colored. With them, it’s really difficult to match the tone by color, although you still have to cover them with wallpaper. The main thing is that your recessed recesses do not differ strikingly in color from the panels themselves. Through not dense wallpaper, such a difference may become noticeable over time.

Putty will not work on wood, take car putty for metal based on epoxy resin. This is the only way the putty will hold at the joints of the panels, plastic without adhesive base will not hold putty even with a sickle - there is such a negative experience. Then process the seams with sandpaper, so that there would be no “shells” and you can glue the wallpaper. but glue is better to take on the basis of bustilat.

You have already been given advice / recommendations about sealing seams on MDF panels, I will add only one thing to you (actually, according to the very preparation of them for gluing). Just be aware that when wallpapering, your panels will need to be completely puttied to ensure good adhesion (adhesion) of the wallpaper to their surface. And don't forget about primer.

It is not necessary to putty completely, adhesion is simple wallpaper paste of course it won’t, wallpaper on MDF can’t be glued to them with high quality, but .. you still need to level the surface, and for this you just need to putty the joints. And you need to glue, for example, on bustilat, glue is perfect for such a case. You can use PVA glue. You can also use Titanium, but it is very difficult to work with it over large areas.

Preparing MDF for wallpapering, what to do?
Preparing MDF for wallpapering, what to do? Go through the joints with sandpaper, then prime them and seal them with putty with gluing the sickle mesh. After that you need to be good

MDF panels are a finishing material consisting of wood fibers that are interconnected by organic resins. Due to their cost-effectiveness, they have earned great popularity in repair work. This material is especially often used for finishing public institutions - offices, shops. A wall or ceiling lined in this way will look aesthetically pleasing and modern. The latest technology made this product completely safe, which allows it to be used in almost any room. For rooms with high humidity, such as a bathroom, series of especially durable moisture-resistant panels are produced.

MDF panels: advantages and disadvantages

Among the advantages of finishing material:

relatively low cost
variety of colors and textures,
installation speed,
safety,
high heat and sound insulation,
practicality.

They have practically no disadvantages. The only significant drawback is the fire hazard. Therefore, manufacturers recommend wiring in special heat-resistant boxes.

Installation can be done in several ways. If you mount the product using a crate, then special preparation of the walls is not required. In addition, communications can be hidden under the crate. You can simply glue the panels to the wall. We will tell you how to glue MDF panels, and how to choose the right adhesive mixture.

MDF panels can also be glued to difficult sections of walls

What glue to choose?

Usually the manufacturer finishing materials gives recommendations on the choice of glue. The right glue for MDF panels is a guarantee that the product will stick firmly and will serve for a long time. Universal means do not always live up to expectations. Although there are universal adhesives which perfectly glue any materials.

Among such generalists, Kleiberit 636 can be distinguished. It is perfectly applied, dries very quickly, and can withstand significant loads. It contains synthetic resins. German manufacturer guarantees product safety.

Moment Crystal is also great for gluing wall panels, including MDF. It has high moisture resistance. Not afraid of temperature changes.

Clay Moment Crystal for panels

Specially designed for the installation of such a finishing material and adhesive composition MitreFix. By applying it, you can be sure of the durability and reliability of gluing.

Often, so-called liquid nails are used for gluing MDF panels. This is a universal adhesive that can withstand significant breaking loads. With their help, you can even glue materials that do not fit together well. Working with this composition is easy and convenient.

Before you decide which glue to glue the MDF panels with, you need to know what parameters the glue is chosen for. The selection criteria for the adhesive mixture are:

high bonding strength,
resistance to temperature changes,
moisture resistance,
not toxicity.

Operating procedure

Unlike the method of fastening panels with a crate, gluing them to a wall involves preparatory work. Here is an example algorithm of actions:

It is necessary to prepare the surface to be glued: level, remove old wallpaper, prime the wall.
Mark the panels with a tape measure, cut to the required dimensions.
Apply glue to the wall or panel (depending on the type of adhesive mixture).
Press down on the panel being careful not to damage the outer layer.
Trim seams if necessary.
It is better to fill the seams with sealant. This will prevent moisture ingress and deformation of the panels.
Leave until completely dry (for a day).

Wallpapering MDF panels

If MDF panels have served you for many years and have lost their former attractiveness, it is quite possible to update them. To do this, it is not at all necessary to buy and mount this finishing material again. Just paste old wall wallpaper.

To the question of whether it is possible to glue wallpaper on an MDF panel, we answer with confidence: it is possible! And not just wallpapers. Self-adhesive and even fabric will do if you have a creative approach to repair. Wallpaper is better to choose textured, foam-based. They will hide the panel joints.

Since the panels are made of wood, they instantly absorb glue. Therefore, wallpapering should occur at a fast pace. And you need to smear both surfaces. First - wallpaper, and at the last moment - panels. It is best to additionally coat the joints with PVA and be sure to roll them with a rubber roller. Otherwise, they may fall apart.

If everything is done correctly, then the panels pasted over with wallpaper will last for many years, and they will look beautiful.

An example of gluing wallpaper on Wall panels MDF

Glue for MDF panels: how to choose and stick
Glue for MDF panels can be selected quickly enough if you know what characteristics are required for high-quality gluing of panels to the wall. Pay attention to the composition of the glue and consult with professionals.

Often when interior decoration premises, we are forced to resort to the use of several types of finishing materials at once. In some cases, this can be explained by constructive conditions and features that are inherent in this room or apartment, and based on which, we must accept certain decisions for interior design. Very often one of optimal solutions becomes use combined species finishes, when several decorative materials are used at once.

This approach makes it possible to focus on the obvious advantages, while hiding, at the same time, some of the disadvantages of both the room itself and each of the finishing materials. To date, one of the most popular solutions is a combination of wallpaper and panels: plastic, PVC, wood, MDF, SIP and others. By the way, this method proved to be excellent when working both in residential and in non-residential premises with high ceilings.

How to glue wallpaper on the panel?

Many people are wondering: is it possible to glue wallpaper on the panel? Plastic (PVC), wooden, MDF and others. In fact, to answer this question, you need to know some details about the use of this decorative material.

Please note that a wide variety of different types of decorative wall panels are presented on the building and finishing materials market.

Let's look at the most popular of them, and see if wallpapering on such surfaces is possible, and how to glue them correctly.

Sticking wallpaper on PVC trim

A prerequisite for such gluing is preliminary preparation working surface. Therefore, answering the question of whether it is possible to glue wallpaper on PVC plastic panels, you should say: yes, you can. However, it is necessary to remember that certain conditions must be met. So, what tools will you need and what is the sequence of your actions? Let's see:

Prepare a primer for plastic and vinyl surfaces, thinner or equivalent, fine sanding paper or equivalent.
First of all, process glossy surface, making it matte so that the wallpaper can gain a foothold on it, and wipe off all the fine dust.
If possible, wipe the surface of the plastic a little damp cloth and wait for it to dry. It does not take a lot of time.
Then it is necessary to apply two primers designed to work with PVC and similar plastic-based materials.
The next stage of work: surface treatment with a special adhesive primer diluted with white spirit. This is done using the appropriate tools.
After that, you can start sticking yourself and no longer worry about the question of whether it is possible to stick wallpaper on pvc plastic panels. The answer is, of course, positive: yes, it is possible!

Work with surfaces on a wooden and combined basis

It should be remembered that today a huge number of decorative panels that can be bought in specialized stores, as well as building supermarkets in Russia and the CIS countries, are made on the basis of wood, or a combination of wooden raw materials and other materials and elements, incl. fastening. At the same time, we can mention not only wooden panels, but also the so-called wall SIP panels (osb on both sides with a layer of insulation in the middle), which are used for the construction of prefabricated housing.

The design features of many of similar materials is that they may not use any special bonding materials, such as glue or resin, in their production. fastening wood chips made possible by the use of strong compression at elevated temperatures, as well as a special level of humidity. Thanks to innovative approach to production, such materials are well known for their excellent operational characteristics.

Wallpaper can be glued to this type of panels, and the work itself does not differ in any features compared to traditional ones. wooden surfaces. Proceed by analogy. By the way, you can preview the articles about that, or similar surfaces.

At the same time, the already popular “liquid wallpaper” is often used for finishing SIP panels. What you need to know about their use:

They have excellent performance and look great.
Able to hide some minor imperfections of the wall on which they are applied.
They are flexible to some extent. In other words, they are able to stretch a little, which is especially important when repairing new buildings.
Easy to install: even a non-professional can handle their application, subject to the instructions and recommendations.

Therefore, the installation of liquid wallpaper on decorative surfaces, as well as on SIP panels - quite simple. At the same time, you should remember that if you intend to use them indoors with increased level moisture (when finishing the kitchen, bathroom, etc.) - it is advisable to apply an additional protective layer of a special varnish.

How to combine

Well, now is the time to understand the features of the application of various combined materials. Let us dwell on the main options that are most widely used in finishing. modern apartments and country houses.

Using Fragments

To do this, you need to make an initial sketch, which fixes ideas for interior design. After that, you will need to prepare well work surface walls, followed by standard procedure pasting. However, that's not all. After the walls have been glued, in some areas, instead of wallpaper, inserts from panels are mounted, thus forming peculiar fragments.

Designer Tip! The edging of such inserts can be performed using separate decorative elements such as moldings.

Combinations using the dimensions of the room

If your room has sufficient height or width, it can serve as a place for such design reception, as a horizontal or vertical combination of wallpaper and panels. Thanks to its versatility, this approach is perfect for any style in the interior. One of the most common methods is alternating various surfaces with wallpaper. So, you can use plastic panels, then wood, then wallpaper, then PVC again, and so on. A kind of circle is formed.

In addition, you can combine not only different kinds finishes, but different colors. As for the correct choice of shades, it is advisable to use special color matching tables for this. Approximately the same as those used. In any case, with various examples You can get acquainted with the use of combinations in the numerous photos presented in this article. Experiment and do not be afraid to glue wallpaper on the panel, as you can see from this material. As for various options combinations, they are only limited by your imagination. Happy repair!

Categories

Popular