Platbands on a door wooden installation. Platbands for interior door structures - we put them on our own without any problems! How to make door frames

Sections of the article:

Any repairs in the house are planned to improve appearance housing, make it more comfortable. One of the final processes is the installation of doors. However, after installation, the door leaf and the frame have an unfinished look, and the open attachment points do not decorate the entire structure at all. How to make a doorway aesthetically pleasing and hide mounting gaps? To do this, you must use special lining - platbands on the door.

Types of platbands

Solid and glued bars should be considered as the main materials for the manufacture of platbands. Most solid beams require painting. Exceptions are valuable wood species. Glued type bars can be covered in the form of veneer or laminate.

When hand-made platbands are made from various wood materials the choice of the form of products is possible. So, platbands can be:

smooth;
Profiled or shaped;
Curly.

Smooth products are standard. Most often, platbands of this type have a convex or flat shape. Such architraves are quite simple and can be made even by a person without much carpentry experience and knowledge.

Profiled platbands are distinguished by the presence of various protrusions and recesses over the entire surface of the product. Shaped platbands are usually made using a milling cutter.

Figured platbands are the most difficult to implement. For their manufacture, it is necessary to use a vertical mill or programmable machines with various templates-blanks. One of the most expensive curly platbands are products with hand-carved decoration.

Materials and necessary tools

In the process of manufacturing platbands, the quality of the base material is very important, since the characteristics of the strength and durability of the future product depend on it. Thus, first of all, it is necessary to determine the type of wood.

The most affordable material in terms of price and prevalence is pine. The advantages of pine lumber include lightness machining wood and trouble-free painting. However, one should take into account several very important features breeds. High-quality coloring of pine products is possible only when the wood is deresined. In addition, given the natural softness of wood, it is important to produce correct handling because pine is easily spoiled under adverse conditions.

The place where the platbands on the doors will be installed also plays a role in the selection of materials. For finishing doorways outside the house, as well as in places high humidity like the kitchen and bathroom, oak is the most suitable option. Despite some difficulties in wood processing associated with the strength of the breed, a product made of oak can last a very long time.

In addition to oak, there are a number of tree species that do not require special decorative processing thanks to natural beauty invoices. These trees include:

The Red tree;
Nut;
Ebony;
Alder;
Birch;
Maple.

To give an ideal appearance, it is enough to cover the platbands made from such wood with a layer of transparent or matting varnish or stain.

Woodworking Tools

In the process of working on the manufacture of door frames, you need to have a small set of standard carpentry tools on hand. These include:

Sandpaper;
Hacksaw;
Milling cutter with various nozzles;
Plane;
Cutter.

With the help of this set of tools, not only sawing and grinding of parts is performed, but also shaping the finished product into curly shapes.

Manufacturing technology

Before cutting wooden architraves on the door with your own hands, you need to decide on the shape of the future product. The difficulty of manufacturing structural parts directly depends on the chosen form of platbands.

flat

by the most simple option is the manufacture of flat platbands. To perform such work requires a minimum amount of effort and time spent.

First of all, it is necessary to measure the perimeter of the doorway that needs to be lined. Based on these data, the sawing of wooden blanks into fragments of the required length is performed. After that, the surface is sanded with fine-grained sandpaper. This is necessary to give the surface evenness. Then the bars are coated with the necessary paints and varnishes.

Shaped or profiled

For self-production of shaped platbands, it is necessary to measure the perimeter of the opening. Based on the obtained values, it is required to trim the bars into elements of the appropriate length. Next, the profiled platbands are decorated by creating various recesses along the entire length of the product. For this work it is used milling machine.

In the absence of the ability to work with a milling cutter, it is quite easy to purchase shaped-type platband blanks in almost any store and market. In this case, there is no need to process the product with sandpaper.

curly

Making platbands of figured type is a rather difficult and painstaking work. When you are ready to work on a product of such a plan, it is possible to make the task a little easier by using templates. You can either draw them manually or print ready-made layouts from the Internet. It is acceptable to place the template on the surface of the workpiece, as well as to transfer the pattern using carbon paper.

The most convenient tool for decorating a product with a carving is a milling machine with various standard nozzles. When performing simple patterns on a platband with a figured edge, it is enough to trim the timber, focusing on the markings.

To create a simulation hand carved on the platbands it is necessary to place the tool in a vertical position. Such a process requires the presence of special nozzles, as well as great perseverance and patience. However, the result is well worth the effort.

decoration

Before you install the trim on the door, you must correctly complete the procedure for decorating the product. The purpose of such events is not only to give the elements of the casing a more presentable appearance, but also to protect against the influence of external factors.

When used as a wood base material, the type of coating depends on the immediate purpose of the treatment. So, if you want to preserve the natural pattern and shade of the tree species on the structure, it is enough to simply cover the platbands with a layer of colorless varnish.

If it is necessary to imitate valuable wood species, it is necessary to apply stain treatment. Also, its use is required before the tinting procedure, after which the product is additionally varnished. To create a protective barrier, structural elements can be treated with wax impregnations.

When processing pine logs, it is best to choose a coating in the form of paint. most acceptable decorative materials paint type are:

Water-dispersion paints. The most popular of them are made on the basis of acrylic. Such paints have a wide range of colors, are easy to apply, dry quickly and have no smell;
Enamel. Paints with the formation of a glossy sheen when dry. They create a stable protective layer in the form of a film that isolates wood from external factors;
Nitro paint. Being a very high-quality means of protecting the product, it has a strong smell when applied and dried. It is recommended to apply the paint outdoors.

Before applying any of the coatings, the product is treated with a primer layer. If you want to create an additional decorative effect in the end, you must use a top coat.

In the process of decorating the product, before installing the trim on the door, it is permissible to cover the structure with vinyl film, decoupage, veneer or laminate veneer. However, all these works can only be performed on flat-type platbands.

Platband installation

The process of making platbands is only half the battle, because correct installation- not like that simple work as it may seem at first glance. The installation procedure can be performed in two ways: using mounting glue or ordinary nails without hats.

Adhesive mounting is acceptable when using light materials for the manufacture of the casing, and is also ideal flat surface walls. When fixing massive and heavy bars, it is better to use reliable means in the form of thin finishing nails. Due to the lack of caps, the fasteners are almost invisible.

Before starting the installation, if necessary, the platbands are cut at an acute angle of 450. This method is applicable in most cases. To perform an accurate cut, a miter box, a protractor, or geometric calculations of the required angle are used.

After cutting, the installation of platbands on the door is carried out from the side of the location door hinges. The side plank is nailed to the wooden beam located at the base of the door frame design. The second side element is attached according to the same principle, after which the upper crossbar is mounted.

When various defects during the installation process, they are masked. For this purpose, you can use a mastic of a suitable color, a cosmetic pencil, or masking furniture stickers.

Trim on the door is an important element of the finished door structure for a house or a bath, which performs a decorative and protective function.

Overhead strips are designed to stylishly frame the doorway, effectively hide visual defects and gaps that exist between the wall surface and the frame.

Installation of door trim is the final stage of installation of doors of various types. How to install platbands with your own hands to ensure the strength and reliability of the finished structure? In fact, this process is quite simple, the main thing is to know some of the features of individual types of products and how to install them.

Types of trim for doors

To find out how to install architraves for interior doors, it is recommended to consider their varieties. Finished products can be classified by configuration, material and installation option.

Configuration

According to the configuration, the platbands for interior doors are divided:

Straight and flat. Standard option, which is different simple execution and attractive appearance. They are suitable for any type of door, combined with any interior solution.
Rounded. Outwardly, they are similar to straight decorative strips, while they have a slightly rounded frontal part.
Curly. Products are made in any shape to order, combined with the original and design options door cloths.

Production material

Modern options for platbands are made from various materials with high performance.

From a tree. Products are made by milling wooden planks. For wooden elements well-dried lumber, spliced in length, is used. Planks made of wood can be straight, rounded or curly. Bath, sauna or log house - the best choice for such buildings - these are wooden platbands.
From plastic. Plastic platbands on the door are made from a safe polyurethane alloy or PVC. They are simple, easy to install and low cost. In addition, these products may have different colors.
From metal. Finished products are made of steel or aluminum alloy. They are durable, practical and durable.
From a composite. Products are made from MDF, plywood or pressed paper.

Installation option

As for installation, you can install platbands on interior doors as follows:

Overhead. Products are mounted on the doorway using ordinary nails, glue.
Telescopic. The slats are installed according to the tenon-groove type, when special protrusions are inserted into the small slots provided.

To obtain a symmetrical doorway, the appropriate dimensions of the main elements must be observed during installation.

Preparing the doorway

Before installing the platbands of interior doors, it is necessary to carefully prepare the doorway. Preparatory work is carried out in stages:

. Since the front strips act as a decorative and protective element of the structure, for this reason, the installation of platbands on interior doors is carried out only after the installation of the door frame and leaf.
Removal of excess mounting foam. After completing the installation of the box, the remaining foam is cut off, which filled the existing gaps between the wall surface and the door opening. The cutting is done with a thin-bladed knife.
Elimination of irregularities and defects. The installed door frame and leaf can cause minor irregularities and defects on the wall surface, which should be immediately eliminated. In addition, the installation of platbands requires an absolutely flat surface in order to avoid deformation of the finished structure in the future.
Wall cladding. Before assembling the elements, it is recommended to complete all wall cladding work using paint, decorative plaster, wallpaper, etc.
Surface cleaning. All work surfaces must be cleaned of dust and debris, and degreased.

Possible mounting options

How to fix platbands on interior doors with your own hands using improvised means? To get started choose one of the 3 available options installation.

Finishing nails

Finishing nails for platbands - this is one of the most affordable and popular installation options. If necessary, decorative trims can be easily removed or replaced with damaged elements.

To simplify the installation process, marks for nails are made on the front surface of the elements, located at the same distance between them. Optimal Distance between two nails - 45 cm.

For driving nails, it is better to use a compact hammer. For grouting the location of the nails, mastic is suitable for the color of the surface.

liquid type nails

The following method of fastening is carried out using a special adhesive composition in liquid form. Glue fastening is reliable and safe. Fixing the front plate is carried out as follows: the adhesive composition is carefully applied on the reverse side of the element, which is pressed tightly against the wall surface for a couple of seconds. Excess glue is removed with a clean rag.

The installation of platbands provides for an effective combination of these two methods, which will increase the strength and wear resistance of the structure.

Telescopic way

This method is suitable for fixing telescopic type slats. Installation is carried out according to the tenon-groove principle, when one part of the element enters its other part. This allows for proper alignment decorative items without the need for cutting. Thorn finished item carefully inserted into the groove in the box.

Making the necessary measurements

Proper installation of platbands involves a preliminary calculation of the required length of the product. To perform washed down strips, first you need to measure its width. Next, measure the same distance from the top. It is recommended to leave a small margin in length equal to the width of the bar.

The standard width of the interior door trim is 7 cm, the thickness is 1.5 cm, and the height is 215 cm. double door– 6 elements.

Finished slats are produced in various sizes, so they differ in width, thickness and height.

Step by step installation work

For work it is necessary to prepare:

Hacksaw for wood.
Fasteners.
Construction roulette.
Square.

All work is carried out in stages:

Prepared products are prepared in height door leaf, the desired length is measured. The element is laid on the floor, measurement is carried out right angle square, cropping is performed.
A bar with an angle is applied to the box, equals vertically and horizontally. The height mark is performed, which is equal to inner corner boxes.
Focusing on the mark, an angle equal to 45 degrees is set. Cropping is in progress.
According to a similar scheme, the bar is prepared from the opposite side.
First, the side strips are trimmed, then the top element. This will prevent the occurrence of errors when installing products.
After completing the preparation, you can install the straps. Small nails are driven into the door box at a distance of up to 45 cm, so that a length of 6 mm for the plank remains on the surface.
To improve the adhesion of the element to the door frame, a special adhesive is applied to the surface.
The finished plank is lightly pushed onto the nail. In this case, it is very important not to damage the front of the product. To do this, a small bar wrapped in clean rags is used as a hammer.
The platband is leveled and pushed onto the nail until it stops.
After installing the side strips, you can proceed with the installation of the upper element, which has angles of 45 degrees.

Now even a novice master knows how to nail trim on doors with his own hands. This process is quite simple, requiring a good eye, attentiveness and perseverance.

Cashing is selected for door leafs according to criteria such as texture, width, color. Cashiers are made from different kind materials, each with its own advantages and disadvantages. More details below.

Cashiers for interior doors are sold in a large assortment, and you can purchase products in a wide variety of shapes (carved, figured, teardrop-shaped, semicircular.) It is this detail that is finishing after which the installation is complete.

Often, door manufacturers do not include platbands in the product package, and they have to be purchased additionally.

For some, this can be a serious problem, but to avoid it, just check the package. Naturally, the cost of the door model with all necessary components there will be much more bare door leaf, but you don’t have to look for suitable item at other outlets. Platbands can be installed with your own hands, installation will not be difficult.

As for the dimensions of the door finish, the following are considered standard:

Width - 7 cm;
Thickness - 1.2 cm;
Height 190 - 235 cm.

In order to finish the door, in which there is one leaf, you need 5 cashiers. If the door has two leaves, then 6. If you need to frame only the doorway, then it will be enough to purchase only 2 strips. What are the best options for cashing out? In this case, we are talking about the material.

You can buy platbands from the canvas:

natural wood;
aluminum;
Become.

They may have decorative coating in the form of a laminated film, veneer, facing plastic, paint composition. Modern manufacturers Planks are made in various sizes, and therefore it is possible to choose them according to your preference.

What are the criteria for choosing cash on the door

It is worth installing platbands only those that are carefully selected, match the color of the door leaf, and are easy to fix. The types of canvases are described above, but what other features of the choice of cashiers are there?

If selected wooden model platbands, then it should be:

Well dried, so that over time it does not start to crack, rot and lose its proper appearance;
evenly colored;
No blue spots
Smooth without notches;
No knots or cracks.

Cash is a product that is not too complicated in configuration, and you can make it yourself. Before you properly mount, you should carefully prepare the finishing element. It is worth noting that the competent selection of tools and materials allows you to start everything. necessary work. First, the workpiece is cut according to the dimensions taken in advance. The calculation is done individually and you should not rely on standard parameters.

The quality of the work performed directly depends on how carefully each canvas will be processed by means of a typewriter or woodworking machine.

After the platband is made, it is polished. Namely, there should be rough grinding and manual processing. The second step is required to remove any circular scratches that remain electric typewriter. Finished platbands must be covered with a primer and antiseptic composition.

How to make door frames

Installing the cashier is not difficult, but first you need to prepare the element. You can find an unlimited variety various architraves from many manufacturers, which may differ in price, finish, shape.

However, many people prefer to install those products that will be made by themselves.

Thus, it is possible to significantly reduce the cost of repair and Finishing work and, besides, it is much easier to mount the finish according to your preferences on your own.

It is definitely worth preparing a number of tools, without which it will be impossible to make, cut or completely cut and attach the cashier to the door:

Saw, preferably manual.
A machine that can make a right angle.
Thickness gauge, which is required to create the correct thickness of the casing.
Vertical cutter.
Sander.
Square.
Ruler.
Pencil.

There are a variety of ways to fasten platbands. For example, you can cut it to size and nail it on nails, attach it with glue, stick it on liquid nails or mastic even to a corner, put capitals on self-tapping screws. Each of the presented options has its own advantages and disadvantages, which are worth familiarizing yourself with.

Proper installation of platbands for interior doors

Nailing the trim on the finishing nails is the most popular option. It has a lot of advantages. If necessary, you can easily remove the platbands. Mounting is quick and easy. To put the finish for the openings, you will need to pick up carnations, on which there is a flat and narrow hat.

The length is chosen, depending on the thickness of the casing, but on average 4 cm is chosen.

If only nails with hats were on sale at the time of purchase, then the hats can be removed with a couple of light movements if you use a side cutter. Before doing the installation of platbands, it is worthwhile to outline the location of the fasteners. A balance must be observed, or, in other words, the arrangement is carried out evenly so that there is no distortion of the structure. Experts recommend installing them at a distance of 50 cm from each other.

Liquid nails are glue sold in tubes. It is very easy to apply and can be used for any kind of architraves. It can be plastic or wooden model. No preparatory work is needed, because it is enough just to squeeze out the composition and press the casing to the right place on the opening between the wall and door panels. The advantages of this installation method are quite obvious, and most importantly, liquid nails dry as quickly as possible, they are as strong as possible, and even when the composition flows out of the product, it is very easy to remove it.

Self-tapping screws are simple and old way installation. It has such advantages as:

Reliability;
Strength;
Ease of installation.

The downside is that with too much impact on the canvas at the time of screwing in the screws, the canvas may crack. The place for the installation of the self-tapping screw must be marked in advance so as not to move even a couple of millimeters. This can also cause a violation of the integrity of the clypeus. Best of all, experts advise pre-drilling holes to avoid the above consequences.

There is also such a method of fastening as beaks. The advantages are an excellent proper appearance, ease of installation. The disadvantage is that they are made of MDF, and it is not only undesirable to remove them after installation, but after all, after dismantling, you can notice chips and cracks on the coating.

We select telescopic trim on the door

There are telescopic architraves on a door. They differ from the usual ones by the presence of a special ledge for easy connection with extensions and the door frame. They are used when the door frame is narrower than the thickness of the wall. Due to this special protrusion, the fastening is carried out through the longitudinal grooves in the door frame. If the installation is carried out correctly, then neither fasteners nor walls will be visible in the opening between the box and the wall.

This method of installing platbands is also:

Reliable;
Lasting;
Durable.

When making platbands on your own, you will need to make the most careful calculations so that the door has a neat and complete look. There are a number of nuances that you should definitely take into account when installing platbands. To hide fasteners in the form of nails or self-tapping screws, you can use a wax corrector or acrylic sealant of the same color as the door leaf.

In order to avoid a gap at the junction of the platbands, each cut of the subsequent canvas must be created, relying on the previous element. If there is a curved wall in the room, then straight platbands will not work. What to do in such a situation? Finishing nails should be used to mount the edges of the trim. Such fasteners are invisible and they allow you to align the finish of the door frame.

If there are minor gaps, then acrylic sealant or, again, wax sealant will be required to mask them. To mask significant defects around the door frame, you can choose wide platbands of the order of 10-12 cm. It is best, in this case, to purchase platbands at custom order. Since the installation of platbands is a finishing touch, the procedure is carried out only at the end of the repair of the room.

Installation is carried out flush at the ends, and visually, it seems that the installation is carried out directly to the wall. Experts recommend choosing thin carnations with a small hat.

Do-it-yourself installation of trim for interior doors (video)

A door without platbands not only looks untidy, but it spoils the whole look of the room. They allow you to hide the edges of the wallpaper, the opening between the door frame and the wall, as well as bring completeness and aesthetics to the interior design.

Hello! The aesthetic appearance of an interior door largely depends on how accurately and accurately the trims are mounted. And how to install platbands after installation door block with the door, we'll talk further.

In the process of installing platbands, we will need:

Roulette, a simple pencil and a wax pencil to match the color of the casing;
a hacksaw for wood and a miter box or a miter saw;
masking tape, a clerical knife blade, a hammer and finishing nails;
acrylic sealant in the color of the trim and foam sponge;

Preparatory stage

Installation of platbands on the door is the final stage of door installation. To this moment:

the door frame must be fully assembled and checked for verticality;
the door is hung and adjusted (easy to open and close);
the gap between the door frame and the wall is filled mounting foam;
a latch handle is installed on the door leaf and a striker on the jamb.

Note: the edge of the door frame and the surface of the wall must be in the same plane and form a flat surface. If necessary, align the wall with respect to the front side of the door block with plaster or putty.

With a sharp blade, carefully cut off the excess of cured foam around the perimeter of the door block, being careful not to damage the decorative coating of the frame.

There are various options for installing platbands on interior doors: using self-tapping screws, liquid nails, snap-in platbands. I will talk about how to fix the trim with finishing nails.

Step-by-step instructions for installing platbands

The platbands are installed in the following sequence: side - top - side. If you first install both side elements, it will be problematic to fit the top one strictly in size. Attach the side trim to the installation site. The frame should be located with a slight indent from the edge of the box, in this case the casing does not interfere with the hinges, the lock tongue does not cling to it when closing and opening the door.

Inspect the bottom of the casing - if it has chips and bumps, cut off the edge. You can cut the platband with a hacksaw for wood, using a miter box for accuracy. But without the skill of such work, it will be difficult to evenly cut trim with a convex or curly outer surface. It is best to use a miter saw.

Install the casing vertically, check the size of the indentation from the edge of the box along the entire length. Make marks on the box with a pencil (in order to later mount the casing exactly in the same place), mark on the casing the place where the 45° cut will be made.

Use a miter saw to cut at the desired angle upper part clypeus, stepping back about 2 cm from the mark (reserve in case of an uneven cut). If the cut turned out to be even, attach the trim to the door frame and measure how much to cut from the bottom end so that the frame element fits correctly.

Then we fasten the casing with the help of finishing nails - they are distinguished by small caps that are recessed into the surface.

Carnations are driven in with an indent of a centimeter from the edge of the casing. Start fastening from the top, firmly pressing the casing in a vertical position. Drive in the first nail at a distance of about 2 cm from the upper oblique cut. Try to make the attachment points in one line, with the same pitch (30 - 40 cm). Finishing nails should be hammered very carefully so as not to hit the platband itself with a hammer. You can pre-drill the holes with a thin wood drill bit. Having fixed the casing with carnations, run your hand over it - the hats should not protrude above the surface and cling.

We put it back, tightly aligning the oblique cuts, and mark the place where the oblique cut will be made at the second end of the upper casing.

Having cut off the second end at an angle of 45 °, we fix the horizontal part of the door frame with the same finishing nails.

Second vertical element mounted according to the same principle - washed down with a margin, checking the accuracy of the cut, trimming the lower end to size, fixing with finishing nails.

note: trim strips may be slightly deformed from long storage, they can be led by a "propeller". For structural rigidity, drive in a stud from the top at the very edge on each side of the upper casing so that the connecting element passes vertically through the junction of the oblique cuts.

Small gaps remain at the joints, they are filled with sealant to match the color of the casing. To remove excess sealant with a sponge without leaving marks, stick strips of masking tape on both sides of the gap, close to it. Apply the sealant from the tube, wet and wring out the sponge immediately remove the excess. You can then remove the masking tape. The same operation is done with the second joint, according to the same principle, it is possible to mask the longitudinal joints of the frame and the door frame, as well as any other joints of the door frame elements. The caps of the finishing studs can be easily masked with a wax pencil in the color of the casing.

This completes the installation of the platbands. The final result depends on how carefully and accurately the work was done at each stage.

Video on the topic "Installing platbands for interior doors":

The main types of platbands
Training working area
Use of nails
Liquid Nails
Telescopic models

How to fix the trim on the door - this question often becomes relevant when carrying out repairs in the house. Doing it yourself is actually quite simple, if you know some of the nuances regarding the types of products and methods for fixing them around the perimeter of the opening.

There are several ways to fasten door frames.

MAIN TYPES OF FRAMEWORK

Before we look at how you can attach trim to interior doors, you should familiarize yourself with their main types. The method of installation directly depends on the specific type of product.

According to the material of manufacture, they distinguish:

wooden;
from pressed paper;
metal.

Varieties of door platbands depending on the material of manufacture

For budget options pressed products are used. IN modern interior MDF products are the most popular type, besides, unlike other types of platbands, any mounting option is available for MDF.

In appearance and configuration, they distinguish:

straight;
rounded;
carved and figured;
typesetting.

Variations of platbands by configuration

Additionally, a capital can be installed above the upper casing. This element plays an excellent decorative role, especially when it comes to the classic style and variations close to it.

With regard to mounting methods, platbands can be installed in three main methods:

on ordinary nails;
on glue "liquid nails";
according to the "thorn-groove" principle.

In order for the opening to look organic, it is important to observe optimal dimensions for all details. Cutting elements can be done in two ways: at a right angle or 45 degrees. In the first case, the upper bar is most often installed above the sidewalls, while it must have an edge processed. With an oblique cut, you need to bring out the ideal angle so that the fragments fit together without gaps. For cutting it is better to use a miter box.

PREPARATION OF THE WORK AREA

Before proceeding directly to fastening the platbands, you should properly prepare the work surface. The entire list of works can be conditionally divided into several stages:

Box installation. The platbands serve as a kind of decor for doors, as they are able to create a spectacular frame and hide minor wall defects. Consequently, their installation must be carried out at the very end after the doors are installed.
Foam removal. After the box dries, it is necessary to cut off the excess mounting foam in order to bring an even level between the wall and the loot, it is best to do this with a clerical knife.
Removing irregularities. If, during the installation of the door leaf and the box, small defects appeared on the wall, for example, concrete chips, they can be repaired with plaster, this will not only facilitate installation, but also improve the strength of the opening. To ensure that no gaps remain during the installation process, the surface for attaching the platbands must be flat.
Wall decoration. Before installing the platbands, it is necessary to complete all finishing work: painting, wallpapering, etc.
Cleaning. Remove all dust and other debris from the surface; when using glue, you must additionally degrease the perimeter of the opening.

Preparation of the working area for the installation of the door trim

USING NAILS

The most traditional way to install architraves is to use nails. In order to hide the attachment points as much as possible, special miniature carnations are used, their peculiarity lies in the almost complete absence of a hat.

In order to properly nail the platbands on the door, you need to set them according to the level. Since when mounting on a wall, distortions or gaps can occur that were not on a flat surface, it is recommended to leave a small excess of material when sawing.

Since nails without hats are used for platbands of interior doors, try not to damage the coating of the cladding itself. It is most convenient to work with a small hammer. You can pre-mark the connection point with an awl.

In order to cover the nails on the platbands, they mainly use a special mastic or grout to match the coating. Minor damage can be masked with paint, felt-tip pen or pencil.

The use of nails is the traditional way of fastening platbands

LIQUID NAILS

Another method of fastening platbands involves the use of special glue. The most popular option is the so-called liquid nails. This compound provides fast traction on almost any surface.

Let's consider how to properly fix the platbands without ordinary nails.

To do this, you must initially determine the exact position of each element. After that, apply a small amount of glue to the back of the plank and press it against the wall. If glue comes out from under the casing, wipe it off immediately. It is advisable to apply only a few dots to prevent spreading.

You can fix the platbands either completely without nails, using glue, or by combining these two methods, this will provide greater structural strength.

Fastening platbands to liquid nails simplify the process

TELESCOPIC MODELS

The simplest is to attach telescopic architraves to interior doors. It is performed without nails, but can be supplemented with glue for greater strength. Mounting features are directly related to their design.

Installation of platbands on the door: two mounting methods

The fact is that the edges of the platbands, when connected, coincide with the edge of the extension or loot. The principle of adhesion is "thorn-groove".

Telescopic platbands are mounted strictly in the groove of the box plank

In other words, one part goes inside the other. Thus, in order to install such products, it is enough just to saw off the excess and dock the parts. The protrusion of the element is inserted into a recess in the door frame. Then you need to set the required distance, which is regulated by the size of the recess.

Regardless of which installation method you choose for a particular situation, care should be taken, as one awkward movement can ruin the entire structure. If there are irregularities on the wall, it is necessary to first align them so that there are no gaps, this applies to absolutely all models of platbands, regardless of the material of manufacture and configuration.

Video: https://youtu.be/Hq2mNmacACs

Site search:

The installation of platbands on the door frame is the final stage in the construction of the entire door structure. Cashings, first of all, serve as a decorating element that closes the interface between the entrance wall opening and the door frame. Ennoble and give a decent appearance will help correct selection the colors and textures of the element, which must be identical or as close as possible to the shade and material of the installed door.

Finishing decoration of the doorway should be done on final stage repair of the entire room - after whitewashing, painting and wallpapering the walls. This, at first glance, simple work, requires some attention and accuracy. The problem here is the exact fit and correct installation platbands on the door - without any gaps and distortions.

Types and classification of platbands

A large assortment of cashing on the building materials market facilitates the choice, and its diversity allows some classification of platbands. They are subdivided:

by material - wood, plastic, metal, composite;
in shape - flat, rounded, curly;
according to the method of installation - on overhead and telescopic.

Door platbands can also include such an element of decor as a capital. It is made mainly from solid wood and decorated with a sophisticated engraving pattern, which gives the whole room sophistication and aristocracy.

When installing platbands on interior doors, it is advisable to focus on the materials from which the door itself is made. If the door leaf is veneered or made of MDF, then there is no need to select material for cashing. In this case, platbands made of laminated MDF will be the most suitable.

It is impossible to give preference to any form - this is a matter of taste. However, it is worth remembering that the classic flat strips for self-assembly will be more convenient to use and help to avoid marriage.

Installation of overhead platbands on the door provides for their direct fastening to the door frame with glue or nails. Installation of telescopic architraves, due to their design features, can be produced without the use of any special elements. Such cashing does not give distortions and does not need additional fasteners.

Telescopic architraves

Them design difference is the presence of a special slotted protrusion made at a right angle and inserted into the longitudinal groove of the door frame. Such platbands make it visually monolithic, leaving the fasteners invisible. They are intended for arranging non-standard openings.

For walls that are too thick compared to the door frame, additional extensions may be required. Correcting with their help the difference between the thickness of the enclosing structure and the width of the box, you can achieve a perfectly neat appearance of the installed door.

Assembly and installation of platbands

To start, define inner dimensions vertical cashing in one of the following ways:

using a tape measure, measure the distance from the floor to the junction of the upper transverse and side longitudinal beams of the door frame;
make a risk on the clypeus attached in place.

The resulting mark will become the starting point for the future cut. Carefully, maintaining an angle of 45 degrees, the bar is cut in such a way that its size with outer side turned out to be more than from the inside.

The use of a carpenter's miter box will greatly simplify the work.

When determining the cut lines on the platbands, it should be borne in mind that their direction will be different on different sides of the door leaf. Do not forget that each plank will require an individual measurement. And yet - to begin the installation of cashing should be from the side of the hinges of the door opening "on itself".

Prepared side trims are not nailed close and only two nails - one closer to the floor, the other in the middle. A blank for the upper bar is slipped into the gap left on top and markings are drawn on it in place for the future gash. This will allow you to get rid of errors and the formation of large gaps during the subsequent pairing of all elements.

You can correct the location of the entire cashing by lightly tapping on the sidewalls of the planks, previously baited on nails. If the gaps are large enough, then one nail is removed from the plank, after which it is given the desired position. The final installation of the prepared platbands on the door is possible only after their careful adjustment in size while maintaining the correct angles and minimum gaps of the parts to be joined.

Fastening

For cashing fasteners, it is best to use thin carnations, in which, after punching into the door frame, the cap is removed with wire cutters. A uniform step of about 15 centimeters will be quite sufficient for reliable fastening. If the adjacent walls of the doorway are even, then it will be enough to fix the platbands in the upper and lower parts with a pair of nails driven in the middle of the plank.

Copper or galvanized nails should be used, as they do not give dark smudges on wood over time, even in rooms with excessive humidity.

For fixing platbands from MDF, a slightly different technology is required. To work with them, blind holes should be pre-drilled with a thin drill in order to minimize the risk of damaging the plank when driving a nail. The same additional preparation must be made when using self-tapping screws as fasteners. But they will require holes that are somewhat larger in diameter in order to drown the caps, which are subsequently covered with plugs to match the trim, or sealed with acrylic putty before painting it.

The use of adhesives or liquid nails is used only for perfectly smooth walls adjacent to the door frame. Such fastening is not possible in rooms with high humidity such as bathrooms and toilets.

Little tricks

When choosing wooden platbands, you should pay attention to the quality of the drying of the board.

How to install platbands on interior doors yourself

Poorly dried wood:

has an uneven color;
has blue spots on the surface;
makes a hollow sound when tapped.

In order not to spoil the workpiece, the length of the cashing should be measured with a margin of at least 1 cm, which is useful when adjusting the corners of the parts to be joined. It is easier to cut off the excess from the opposite end of the bar.

Not worth marking on front side use a waterproof marker. It will be difficult to remove traced lines with a simple erase.

Trimming of platbands is best done with a miter saw. She will provide clean cut without chips. Gently correcting cut corners is easier than tape grinder. With its help, you can achieve perfect docking in the corners.

If gaps formed during the installation of platbands on the door, they can be made almost invisible by using a mixture based on beeswax, which is purchased at a building supermarket. Heated and brought to the state of a plastic mass, it perfectly fills the gaps formed.

Visually, the cashing looks better, towering 10 centimeters above the doorway, and the same platbands on all doors will provide a single style of the premises in the apartment.

06/15/2015 at 10:06 am

From which it follows that liquid nails glue can be used when working on almost any surface, but more on that later. Glue liquid nails are nothing more than just a dense adhesive mass placed in plastic tubes for convenience. But from where the ordinary construction adhesive got such a name, now we'll talk.

Initially, when it was first made, liquid nails glue was just an ordinary building universal glue for different surfaces! But since this construction adhesive was produced by a company with such a name as Liquid Nails, who knows English understood who did not, I will explain to him:

Liquid Nails is nothing more than liquid nails and our people, or maybe marketers, put glue, liquid nails, to the word.

Sticking platbands with adhesives

It is only necessary to ensure the complete fit of the platbands to the wall and door frame.

Any adhesive materials can withstand a certain load and, with a large weight of the platbands, will not be able to hold the platbands on the plane in a quality manner. When choosing one or another adhesive composition, specify the weight and properties of the platbands. You can stick platbands on liquid nails, or you can fix them on silicone or mounting foam.

Miter saw for trimming platbands

In order for the platbands to hold firmly, they must be properly adjusted and secured.

Installation of doors in Vladimir and the region

The plinth is more convenient and it is better to cut to already installed platband, since it is less likely to miscalculate in the calculations and make a mistake. If the wallpaper is glued before installation (or the walls are painted), then the trim will hide the edge of the wallpaper sheet behind it. If the wallpaper is pasted after installing the trim, then the adjoining of the wallpaper can be quite noticeable and not aesthetic. If the doorway is significantly more sizes door block, then when wallpapering, you need to leave an allowance on the sides and top, otherwise the trim may not reach the edge of the wallpaper, as in this photo above.

There are two traditional options for sawing the architraves - at an angle of 90 ° and at an angle of 45 °.

The 90° angle is used on straight, even architraves without rounding at the request of the customer.

Useful articles and reviews on the repair topic

So it will be easier not to get confused and this is a guarantee that everything will turn out beautifully.

– As you know, the casing must “stand” on the floor, and in order to avoid a gap between the casing and the floor, the lower edge of the casing must be sawn off (trimmed) at an angle of 90 °, since the factory cut may not always be correct. Of course, it all depends on the specific manufacturer, the quality of the product, its quality level, but this preparation procedure should not be ignored.

- Attach 2 trims to each other reverse side to understand whether they are the same width, it happens that the strips differ in width by 0.5-1 mm.

How to insulate a window slope?

Finishing nails are convenient in that if the need arises, you can always dismantle the casing and then install it again. For work, take nails with a flattened hat, 40 mm long and 1.4 mm in diameter. To make the work go faster, pre-make holes in the platbands at a distance of 5-7.5 centimeters. After you drive in the nails with a side cutter, remove the hats, and mask these places with a special wax pencil that matches the color.

The second way is to fasten the platbands with liquid nails.

Installation of interior doors

This will avoid splitting and, accordingly, the formation of cracks on the visible part of the box.

Installation of interior doors. Stage 6. Installing the box. assembled box insert into the opening and fix with wedges from above so that approximately the same distance remains on the right and left. Align the box with the wall on the hinge side. Check the vertical with a level. Fasten the box to the wall with screws at the top and bottom.

Installation and installation of skirting boards and platbands

In the store we find the right skirting board and measure its length. We take the figure we have and divide it by the length of the plinth, and the amount of plinth we need is ready.

Skirting boards can be made of wood or plastic, with or without a cable channel. The wooden baseboard mainly goes to the laminate or parquet board, so that you should not press the plinth tightly against it. There are two mounting methods wooden skirting boards- using self-tapping screws and liquid nails.

Installation of platbands is the final stage in the installation of interior doors.

Installation of platbands on the door with liquid nails

1. Filing of stock platbands. Using a tape measure, measure the distance H from the floor to the lower edge of the groove in the upper bar of the box (Fig. 34); subtract the height of the plinth block from this size, you will get the size into which you need to cut the trim. File the stock trim at a 90° angle.

2. Connection of platbands with decorative elements. Insert the perforated plate into the groove on the back of the trim and decorative element.

Proper installation of interior doors

The parts of the box are connected using self-tapping screws.

The box is installed as follows:

Doors are installed on hinges pre-attached to the door and frame. You must first hang the canvas, checking how smoothly the door closes, to adjust, place the spacers slightly below the door handle and above the upper hinge. After that, you need to check the door again - for example, it should not move independently in a half-closed position.

When the canvas is installed perfectly evenly, the joint between the door frame and the opening can be filled with mounting foam, after removing dust and wetting the surfaces.

Installation ()

Creating a flawless cut requires the use of a miter box. The joints formed during the installation process are recommended to be glued. The plinth will be removable if you put caps on the caps of the screws.

For more clarity, look below, it will illustrate all the above information and give you confidence in your abilities!

If you do not have the opportunity or desire to do the installation yourself, you can contact us, our masters will quickly and efficiently perform this work!

The cost of installing a plinth - from 190 rubles.

Installation of platbands on the door with liquid nails

Let's take a look at them in detail.

1. You decide to install the doors yourself in your room, apartment, country house? A commendable solution, the success of which directly depends on your locksmith and carpentry skills. If you think that installing an interior door is easy - feel free to fight! Perhaps saving a decent amount by wasting some amount of time.

How to install platbands on interior doors

The main thing is that the result of the work does not look like this.

Door installation

Thresholds at the frame of modern doors, as a rule, are absent, but at the request of the client they are included in the kit.

Note: Threshold is most often used in entrance doors to preserve heat in the house, but it is not advisable to use it in interior doors, since it will prevent air exchange between rooms.

If you order a door made of aged wood with a certain design, then along with it you should order hinges, linings, a lock mechanism (lock or latch with a latch) and handles that best match the style of the door.

What you need to know before installing a door

Door installation can be carried out only after laying the finishing floor covering and after finishing the walls in the rooms between which it will be installed, i.e.

Installation of platbands on the door with liquid nails

In this case, you do not have to deal with complex fasteners, drill a wall, floor or ceiling. Not only a specialist, but also any other person can work with glue.

As a rule, the packaging indicates what can be glued with this substance, how to apply it, and how long it dries. In construction, adhesives are used for parquet, linoleum, carpet, ceramic tiles, laminate, porcelain stoneware, ceiling panels, marble facing slabs, wooden planks, etc.

http://remontavtosvoimirukami.ru

To give the living space a complete and most aesthetic look in terms of design, it is enough to learn how to install platbands on the doors. Installation of cashing is done by hand without any problems. The main thing is to take into account some of the nuances of such an operation.

Platbands from different materials and the nuances of their fastening

The products we are interested in are decorative elements, performed in the form of overhead strips on the door. Their task is to form a special frame on interior door structures, which hides gaps and possible construction flaws between the door frame and the wall plane. Platbands are currently made from MDF, natural wood and plastic.

The wooden cashier is now rarely used, as it is subject to temperature fluctuations, as a result of which its appearance and geometric parameters may change. Planks of wood are usually fastened with nails of small thickness without caps or "liquid nails". The latter are used only in cases where the wall surfaces adjacent to the door are perfectly aligned. If it was not possible to achieve ideal evenness, during operation, gaps will necessarily form between the wall and the casing, planted on “liquid nails”.

MDF platbands are less susceptible to the harmful effects of temperature changes. At the same time, visually they are almost indistinguishable from more expensive and "capricious" wooden products. On the door, MDF strips must be placed with your own hands as carefully as possible. They are easily damaged due to the fragility of the material. When using nails, such strips are first drilled under the fasteners, and only after that the installation work begins. At the same time, the preliminary holes are made of a small section (about 1.3 mm) and not through. In addition, cashing from MDF on the interior door is allowed to be glued.

It is best to purchase veneered or laminated MDF strips. Firstly, they look very good, and secondly, they are characterized by excellent operational properties. By installing such products on different types with your own hands once, you will enjoy their beauty long time. Excellent performance and plastic architraves. They are very easy to attach with glue. It is allowed to mount such strips on wall surfaces with irregularities (not very serious). A plastic cashier is inexpensive, you can always replace it with a new one without regretting the money spent.

Features of joining platbands

When installing cashing on interior doors with your own hands, an amateur master needs to ensure that the structure does not have gaps, and the areas where the planks are joined are perfectly even. The easiest way to join products made in the form of rectangles. In this case, they are "lapped" to each other at a right angle.

Docking can be done both vertically and horizontally. Note! Before joining, the saw cuts of the platbands must be protonated with a suitable varnish or painted.

In practice, for interior doors, strips with a shaped shape on the front side are most often used. It is impossible to connect them at right angles. Here you will have to work hard to correctly make the required angle with your own hands (usually it is 45 °). Sawing the casing at an angle is carried out with the help of a miter box. The saw needs to be taken with fine teeth. It is optimal if sawing is carried out on a trimming unit with a swivel type platform. With such a unit, you are guaranteed to receive platbands with an impeccably smooth and even edge.

If you cannot accurately and correctly cut planks with shaped relief at a given angle, the door structure will “gape” with unattractive gaps. When you are not confident in your abilities and the quality of the tool used, it is better to give the platbands for sawing to the workshop. Then you are guaranteed to get at your disposal "ideal" strips for interior doors.

Do-it-yourself cashing installation - instructions for home craftsmen

Installation on door structures it is right to make planks from any materials: before you mount the plinth; after pasting wallpaper (if it is planned to put trim on both sides of the door leaf, their installation is carried out after pasting both adjoining rooms).Important! Planks begin to be placed on the side where the door hinges are.

First step installation work do-it-yourself measurements. We take an ordinary tape measure and determine the distance from the floor to the docking area of the hinge and ceiling beam from the side of the hinges. To the value obtained as a result of this measurement, another 10 millimeters should be added. Measure the opposite side in the same way. It is necessary to make a second measurement - these values \u200b\u200bare not always the same.

we saw off vertical blanks to the required length and put them in place;
we bait (at the base and after about 100 cm up) the side planks with nails;
under the upper loose ends of the cashing, we put a blank for a horizontal platband and mark points on it that will allow us to correctly cut the bar with our own hands at a given angle.

Sawing off a horizontal cashier is carried out by an ordinary mechanical or miter saw. After that, it must be put in place and proceed to the final fastening of all three parts of the door trim. If you plan to fix the structure with thin nails or studs, it is better to take copper or galvanized hardware. They are driven in in increments of 15 to 50 cm. It all depends on your desire and the expected intensity of door operation.

It is optimal to choose a distance between fasteners of about 40–50 cm. If you are sure that the doors will open / close very actively, drive in hardware in 15–20 cm increments. Hide the presence of studs or nails on the casing with acrylic sealant or a wax-based corrector. It is not necessary to use these compositions in cases where the platbands are fastened with “liquid nails” and when they are glued.

Categories

Popular