Painting shelves from chipboard. Painting chipboard at home Processing chipboard before painting

• Lacquers are mainly used to give antique furniture, but well-groomed appearance, noble and rich. In this case, the surface is painted over several times after each layer has completely dried.
• Varnishes are also needed to fix the color and protect the surface from scratches and minor damage.
• Lacquer will be needed even if you decide to paint the chest of drawers antique or in Provence style.

The choice of brushes and roller

After choosing a paint, special attention should be paid to brushes and rollers. Why not save on painting supplies if you decide to update the chest of drawers with your own hands?

• At right technology old surface treatment and good painting cabinet will maintain its appearance for several years.
• When using bad brushes, you will not save freshly painted furniture from sticking hairs or lint, which is almost impossible to fix imperceptibly.

If your task is to paint a large smooth surface, then for work suitable for both roller and aerosols.

ATTENTION: Do not leave the brushes dry during work, it is better to put them in a jar of water, otherwise they will quickly become unusable

Technologies and methods of painting

Do not forget about other important painting tools and materials, such as sandpaper or grinder, primer, putty, thinner and varnish. All this is necessary to comply with the technology of proper staining.

Equipment:

1. Sandpaper different grit is needed for preliminary rubbing of the old layer of paint and surface polishing.
2. Primer needed for sealing small cracks on the surface of wood or chipboard.
3. Putty (you can take a car putty) and a spatula will come in handy if there are deep scratches, chips.
4. A solvent or white spirit is needed to degrease the surface before painting for better impregnation.
5. The varnish performs a protective function and gives the furniture a shine.

In general, preparing a cabinet for painting consists of 5 short but very important steps.

1. To start carefully remove the old paint and with medium-grain sanding paper(or machines) level the work surface.
2. All dust must be brushed off, but without using wet rags, sponges etc. Otherwise, the old paint will only absorb better, and the new one will fall poorly.
3. After processing with the finest grain degrease with white spirit(acetone) and apply a primer coat for better adhesion to the paint.
4. If there are large chips, then pre-fill them with putty and rub them to a smooth state. After that, we apply one or two coats of primer.

When you know all the preparation steps, it's time to move on to the main step and figure out how to paint a wooden chest of drawers and chipboard.

Master class number 1. Painting under the stencil

Everything is mixed up in this closet - romanticism, Chinese motifs, and even something from Gzhel. Everyone sees something different in him. Let's learn painting techniques.

Materials and tools

• Prepared cabinet;
• white paint;
• solvent;
• spray paint blue;
• gold paint;
• stencil;
• brushes.

Walkthrough

Step 1.

• We remove all fittings, locks, handles, etc. from the cabinet. Using familiar technology, we will prepare a wooden cabinet for painting.
• On the working surface (on the floor) we spread newspapers or big piece polyethylene, so as not to spoil other furniture.

Step 2

1. We take white enamel and solvent. In a small plastic jar dilute the paint and solvent according to the instructions on the can of paint.
2. The paint consumption is also written on the bank, it is better to use this information and dilute immediately required amount. If you mix a little paint, then the second time you can get a different color.
3. Making the background of the picture applying the first coat of paint. Leave until completely dry.

Step 3

1. If the color is saturated and you like it, then take a stencil and put it on the cabinet. Attach carefully to front side and side walls so that there are no bubbles.
2. Shake the spray paint well and spray it on the stencil. For an even color, one layer of blue paint will be enough, so we do everything the first time.

Step 4

Till blue paint dries paint accessories taken from the closet, in gold leaf. After the parts are dry, screw them into place.

We remove the stencil from the closet and place it in the most visible place in the room - because now it deserves special attention!

You can decorate the cabinet under the stencil, for example, with flowers.

Master class number 2. Updating the cabinet from chipboard

This closet looked very cheap as it was designed from chipboard. But we updated it with a beautiful ornament for the children's room, now it can even fit into the interior of high-tech or modern.

Materials and tools

• Prepared cabinet;
• white paint;
• pencil;
• building level;
• sponge-brush;
• masking tape;
• additionally: protective paint (enamel).

decor process

Step 1.

1. Prepare furniture by cleaning surfaces from roughness, chips, cracks with putty and primer.
2. After use special means need to give dry surfaces completely.
3. Take painter's tape and stick it on the front side of the dresser according to your individual idea.
4. We make combinations of triangles along the upper and lower edges, rhombuses in the middle, rectangles in the upper and lower parts. We cut off the strips and make shapes out of them, as shown in the photo.

• We make a rhombus by cutting strips of the same length and placing them perpendicular to each other.
• To make rectangles, first stick the tape evenly, parallel to the cut of the chest of drawers, and using building level and a pencil, mark equal intervals. Cut through one.

TIP: Pay attention to the placement of the fittings (handles, locks) and the gaps between the drawers - let it be symmetrical rather than even.

Step 2

Step 5

Final step - application protective enamel. It will extend the life of the chipboard cabinet and protect against small mechanical influences such as moisture and dust.

And so stylish closet ready for active use!

Color options can also be as in the photo below.

Master class number 3. Painting a polished cabinet

Someone can’t believe that from an old polished cabinet you can make such a candy in vintage style, and without loss of functionality. And then it is told how to do it.

Materials and tools.

• Old polished cabinet;
• vintage paint (plain acrylic matte);
• white spirit or acetone;
• brushes;
• sandpaper or grinder;
• golden drawer handles.

Coloring process

Step 1.

Despite the fact that we create a vintage effect, the real shabby chest of drawers is useless. Therefore, we carefully prepare it for painting.

1. To do this, we remove all the old fittings and use a grinder to process the entire surface of the chest of drawers. First we use coarse sandpaper, then fine-grained sandpaper.
2. Puttying and priming is not necessary, except for serious chips on the surface. Degrease the surface with white spirit or acetone, let it dry.

TIP: Since the paint will be applied in several layers, it is very important that it is well absorbed into the wood.

Step 2

1. We cover with the first coat of paint. Very thin, you can not try too hard and leave unpainted places.
2. We rub the first layer with fine-grained sandpaper. We clean from dust, but do not use wet rags, sponges, etc. in the process. Wash only with a dry cotton lint-free cloth.
3. Next, apply a second coat of paint, also rubbing it. Let it dry and rub again a little.
4. So repeat until the color becomes even, but a little rough. For this we used matte paint with a vintage effect. After a few days, it will completely absorb and dry out and begin to turn yellow (pay attention to the instructions on the can so that you do not have to repaint everything again later). To avoid this, you can try this staining method on a small and inconspicuous area. Proceed to full coloring when you are satisfied with the result.

If you bought new handles, check if they match your color and screw them into place. Golden brass carved handles with patterns fit the white antique chest of drawers.

Check the chest of drawers for compliance with your requirements - it is still comfortable, beautiful, and here's the paradox - modern. Vintage is in fashion now!

Wallpaper or film

Applying a film or any other to update the cabinet paper cover, it should be remembered that we use the closet every day. And usually such a coating does not last long, but it is very simple in execution.

Cloth covered

This is the most painstaking way to update the cabinet, when the fabric is stretched over the entire plane. The method is quite outdated. But maybe someone will like it.

Dot painting for a polished cafe

Dot painting is perfect for a polished cabinet. In this case, it is not necessary to remove the varnish and grind the surface. The technique is simple:

• Draw with a marker
• The marker is painted with paint using dots. Details - here.

Ideas for updating the closet

Sometimes when remodeling furniture, the question arises of how to paint chipboard. This material is one of the most common materials for making furniture, it is also used in construction and repair work. Chipboard ( particle boards) have been used for more than a dozen years in various fields, furniture made of this material is especially common.

Chipboard consists of wood chips glued together with formaldehyde resin. Since the chips under the influence external influence can be peeled off, they are protected by an outer coating - this can be a layer of varnish, paint, polypropylene film etc. In addition to protection, painting chipboard creates and decorative effect, since this method can create surfaces not only different color but with different textures.

To restore an attractive appearance Chipboard is enough to update the paint layer, so that the products of this material acquire their own unique style. Also, painting chipboard increases its moisture protection and gives the material resistance to ultraviolet rays. With proper painting work old furniture and other chipboard products not only receive the new kind but also prolong its lifespan. Also, coating chipboard with paint reduces its impact on humans (over time, resins tend to evaporate, and paint prevents this process).

An important point is what is covered with chipboard on top - varnish. Veneer, paint, film or coating is missing. Of all the options listed, laminate is the most difficult to carve. It must be covered with several layers of primer and no one guarantees the result.

Preparing for staining chipboard

Before you start painting chipboard, you must carefully prepare the surface. The result of staining will depend on the quality of the preparation. Usually, to “ennoble” the appearance of chipboard products, they are covered with a layer of varnish or paint, but over time they crack and peel off. Removing varnish or old paint from the surface of furniture is often difficult for craftsmen. Certainly, it is long and laborious process, but surfaces can be cleaned.

To remove a layer of old coating from chipboard, two methods are used:

• Chemical. When the surface is treated with various chemical compounds(washes). They are selected depending on the composition of the old paint. Carefully follow the conditions of use indicated on the label of the wash to avoid trouble.
• Thermal method. In this case, exposure to hot air or steam is used. Required building hair dryer and spatulas (scrapers). A stream of hot air is directed to the painted surface, and when the paint softens, it is removed with a scraper. It is important to follow the correct temperature regime so as not to damage the chipboard.

Also, the surface of the chipboard must be puttied and sanded. This will save the product from minor defects and scratches, which are especially noticeable under a layer of fresh paint.

Before applying putty, the surface must be primed with a suitable composition. For chipboard is better choose elastic putties, for example, acrylic. This will protect the product from cracks on the surface. Putty is applied with a spatula, trying to form a uniform layer. After the putty has completely dried, the surface is treated with fine-grained sanding paper. The product is skinned with it until all irregularities disappear. Then the product should be cleaned of dust, and you can start painting.

Paints for chipboard

For painting chipboard the best option will use a spray gun or spray paint. This will give a smooth surface without smudges, but it is better to practice beforehand, especially if the airbrush and spray paints have not been used.

As for the types of paint, you can use alkyd, oil or acrylic paints. At different types paint coloring result will also be different. You can paint with a brush or a roller with a short pile, and in last version color uniformity will be better. After painting, you can varnish the product, this will increase its resistance to mechanical stress.

Chipboard painting technology

1. The surface is cleaned of dust, dirt and degreased.
2. With the help of rough sandpaper clean the surface so that scratches remain - this is done for better adhesion of the primer to the surface.
3. A primer is applied (you can take an alkyd or even an automobile one - for bumpers).
4. Next, apply acrylic primer.
5. Paint the surface with the selected paint with a roller or brush in several layers (at least two). In general, the number of layers depends on the desired end result - someone needs a translucent coating, and for someone a rich, dense color is important.
6. If, after applying the first layer, irregularities appeared, then it is necessary to re-sand the surface with fine-grained sandpaper and apply several more layers of paint.

• Before painting, chipboard products must be treated in such a way that the glue in the sawdust stops evaporating harmful substances and the surface does not absorb moisture. This is achieved by impregnation deep penetration. You can also use NC varnish, but impregnations are more harmless.
• Before varnishing chipboard, it must also be treated with deep penetration impregnation.
• To highlight the texture of wood chipboard can be treated with alkyd pigments or English patination ( special composition for patination and texture highlighting).
• To achieve a smooth painted surface it is necessary to use short pile rollers as long pile leaves a pattern. By the way, it is in this way that texture can be achieved on the painted surface.
• If it is necessary to paint furniture made of dark-colored chipboard, then it is better to cover the surface with two layers of a dense primer, otherwise dark shade will still be visible through a layer of fresh light paint.

Chipboard today is one of the most common materials in construction and decoration. It forms the basis of pieces of furniture that sometimes you want to update. Great solution for this is staining. But first you need to choose correct composition and learn how to apply it.

The choice of paint and its types for chipboard

If you are faced with the question of how to paint chipboard, then you should understand the varieties of such mixtures. Among others modern manufacturers offer acrylic paints, alkyd compounds, as well as oil mixtures. You can pick up paint in a spray can or paint composition which can be applied with a spray gun. The main tools are brushes and rollers.

After painting, a layer of varnish can be applied to the surface, which will increase the resistance of the material to mechanical damage. Quite often, experts advise preferring acrylic paints to others. This is due to the fact that they do not have bad smell, are water-based, and working with such mixtures is quite simple.

Once applied, acrylic paint dries fairly quickly. Work can be carried out directly in the apartment, which will not entail the need to vacate the premises, because there will be no unpleasant odor. Since such a mixture is made on water based, it can be diluted with water if the mass is excessively thick. Working with paint is easy, because inaccurate strokes and the results of incorrect movements can be removed with a rag soaked in water.

In order to get the most quality coating, before painting, it is necessary to carry out a primer on the surface acrylic composition. If the pieces of furniture are metal elements and fittings to be used open fire, then it must be painted with a special fire-retardant paint for metal.

If you have already decided how to paint chipboard, then you must choose a tool. In hard-to-reach places, it is best to work the surface with a brush. painting tool, be it a roller or a brush, must be designed to work with acrylic paints.

The quality of the coating will depend on the quality of the selected tool, so it's not worth saving. In the process, it is necessary to rinse the rollers and brushes from time to time, not allowing the material to dry on the work surface. It is recommended to buy several brushes in advance different widths, as they may be required to treat certain areas.

It is not enough to know what paint to paint chipboard. This is only part of the success. It is also important to prepare the surface well. To do this, it is imperative to repair the cracks that often appear in pieces of furniture made of chipboard. This contributes to the ingress of moisture into the structure, due to which the material begins to deform.

To carry out the work, it is necessary to fill the syringe with PVA glue and put on the needle. The crack gap should be filled with the compound. A clamp is then attached to the plane. She is left for a day or two. After that, you can continue the restoration work.

You can also get rid of cracks with putty. The mixture can be applied with a spatula in 2 layers. The first is distributed over the surface as evenly as possible and left until the composition dries. The second layer of putty is applied after that.

Work performance technology: priming

The answer to the question of whether chipboard can be painted is an unequivocal yes. Before starting work on applying paint, it is necessary to prime the surface, which is quite milestone. A thin roller is perfect for this. After the primer has been applied, the chipboard furniture or material must be left to dry.

Preparatory work

If you want to know how to paint chipboard with your own hands, then you need to familiarize yourself with the work algorithm. It provides for the preparation and subsequent application of the coating. At the first stage, it is necessary to remove old coatings such as varnishes and paints from the surface. Use sandpaper for this. The skin should have a large grain, and it must be driven along the fibers.

Next, using a flat brush, dust residues are removed from the surface. In those places where the sandpaper did not reach, it is necessary to process with fine-grained sandpaper. Dust is removed with the same brush. After sanding is completed, it is necessary to clean the room. All surface details are wiped with a rag. Debris should not stick to the fresh coating, so the room must be carefully cleaned.

Additional measures for removing old coatings

If you have already decided how to paint the chipboard, it is also important to think about how to properly prepare the surface. From old decorative coatings can be removed by chemical or thermal methods.

The first method involves the processing of chipboard with washes. You can choose one of them, given the composition of the old paint. It is important to comply with the conditions of use in order to avoid trouble. Concerning thermal method, then it involves the use of steam or hot air. For such work, you will need a building hair dryer and scrapers, the latter can be replaced with spatulas.

The jet of hot air should be directed to the surface. Once the paint has softened, it can be easily removed with a scraper. It is important to observe the temperature regime so as not to spoil the chipboard. Additionally, the surface can be puttied and sanded. This will save the product from scratches and defects that will be visible under a layer of fresh paint.

Before you paint old chipboard, you can putty and prime the base. To do this, you can use an elastic acrylic-based putty. This will protect the product from cracks. Putty is applied with a spatula. You should try to form an even layer. After the composition has dried, the material is processed with fine-grained sanding paper. The product is skinned until it is possible to get rid of irregularities.

Coloring process

If, thinking about the question of how to paint chipboard, you decide to choose acrylic paint, it is important to check before starting whether it has the necessary consistency. The mass should not be too thick or liquid. You can choose the number of layers yourself. After the paint has dried, do not rush to assemble the structure. It needs to be varnished first. It is applied to the surface with stamping movements using a sponge. In order to achieve the effect of gloss, it is necessary to apply varnish in two or three layers. After the varnishing procedure is completed and the varnish has dried, the furniture can be assembled.

If you want to paint furniture made of chipboard with your own hands, then you need to clean the surface and degrease it. Using sandpaper, the material is cleaned to leave scratches. They will allow you to achieve better adhesion of the primer to the surface. The primer can even be automotive, designed for bumpers.

The next step is to apply an acrylic primer. The surface is painted with a roller or brush in several layers, but there should not be less than two. The amount will depend on the desired result. Some prefer to see a translucent finish, while others prefer a rich, dense color. If after applying the first layer you see irregularities, then the surface is once again sanded with fine-grained sandpaper, after which you can apply paint in several layers.

Before you paint a chipboard cabinet, you should familiarize yourself with some of the subtleties. For example, it is recommended to process the product before painting so that the glue in the sawdust does not evaporate harmful substances, and the surface stops absorbing moisture. This effect can be achieved by deep penetration impregnation. You can also use NC varnish, but impregnation is preferred, as it is harmless.

Before varnishing, the material is treated with deep penetration impregnation. In order to highlight the texture of wood, you can apply alkyd pigment or English patination. These compositions are designed to highlight the texture.

To obtain a smooth surface after painting, it is necessary to use a short pile roller, because long hair will leave a textured pattern. With the help of such a tool, you can achieve a special effect. Now you know how to paint chipboard at home. But you must also consider what color the piece of furniture has. If it is dark, then it is better to apply the paint and varnish composition in two layers and use a dense primer, otherwise the dark shade will shine through a layer of fresh paint.

The use of different colors when staining

After preparatory work you can start coloring. There must be several layers so that the structure of the plane is not visible. First, use paint a tone lighter than the selected color. Then work is carried out with the main shade. The brush must be driven in one direction so that the paint is evenly distributed. If staining is carried out in several colors, then it is recommended to use masking tape, which is glued to the edges so that the paints do not mix.

It is important to correctly determine the time that will be enough for the final drying of the paint. This will take about 2-3 days. Do not use unpainted chipboard, as it can release harmful substances during operation.

Finally

If you are afraid that a dusty coating will be noticeable on the surface after staining, then it is better to use NC varnish, which is applied in two layers. But if the furniture already has a coating, then ideal solution will become oil varnish PF-283. If you want to give the coating a certain shade, then it is best to use tinted alkyd varnish, which is offered for sale in a wide variety. In order to get the effect of gloss, it is recommended to use a yacht varnish, with which the furniture will look perfect.

Dealing with internal and exterior trim rooms we often use sheet materials such as chipboard. This material allows, where necessary, to easily obtain perfectly flat surfaces. Chipboard is also one of the most common materials for making furniture, it is widely used in construction and has been used for a variety of tasks for several decades. Very often, when making or restoring furniture, the question arises, how to paint chipboard with your own hands?

A chipboard product, as a rule, is the result of a lot of work and therefore it will be very disappointing if ugly painting spoils many days of work. In such a seemingly uncomplicated matter as a repair or decorative coloring surfaces from chipboard, has its own characteristics and pitfalls, therefore, compliance with the painting technology, right choice tools and materials will allow you to perform these works at home beautifully and efficiently, and the coating will make it durable and resistant to any damage.
Today the market offers very wide selection very different coloring materials and compositions, while the chance to make a mistake in the choice of paint and the technology of its application becomes only greater from this. Having studied given material, you will learn how to paint chipboard with your own hands, what paint to choose, and also get a number of important tips directly from the dyeing process.

To paint the chipboard with your own hands and not turn the house into a paint shop, prepare in advance necessary tools and materials.

What do you need to paint chipboard with your own hands?

Primer - Acrylic primer can be used
Paint - alkyd or acrylic, spray or conventional
Brushes and roller if you will be using regular paint instead of spray paint
Acrylic clear lacquer- it will protect the painted wood surface from damage, as well as give color depth and shine to the new coating
Respirator and gloves for protection during work
Solvent for degreasing the surface before painting (you can use white spirit, kerosene or special degreasing compounds)
Cloth napkins or just dry clean cotton rags
Masking tape and paper or covering film
Sandpaper very fine grain
Spatula and putty, best of all automotive, will be needed if you plan to clean deep scratches or chips.

So, let's go directly to work with our product or structure made of chipboard materials.

Step by step instructions for staining chipboard

Step_1 Workplace preparation. Before starting work, cover the floor and (preferably) the walls of the room with a covering film or newspapers.

Step_2 If you plan to paint chipboard furniture, before starting work, remove all parts that cannot be painted: unscrew handles and other fittings, remove glass, and remove drawers. It is also preferable to paint doors and facade elements, having previously removed them - this will allow you to apply the paint with the highest quality and evenness, avoid unpainted areas at the joints, etc.

Step_3 Removal of old paintwork layers. If you are not painting a new product, but carrying out repair painting of an old chipboard product, you must, if possible, get rid of the old paintwork. If the old coating is already peeling off strongly, and in some places it has completely peeled off, it is better to remove it completely. To do this, you can use special washes of old paint, or a building hair dryer, or do it by hand - using grinder or sandpaper. If the old LC coating is holding up well, then you can simply sand old surface to keep it even. Use fine-grained sandpaper for this.

Step_4 The next step is to clean the surfaces from dust and dirt. To do this, use warm water and a cotton rag, if heavily soiled, you can add to the water detergent and then dry the surface with dry cloths.

Step_5 Degrease the chipboard surface with a non-slip solvent such as white spirit or acetone.

Step_6 AN ADDITIONAL STEP. Alignment. If there are deep cracks or chips on the surface, they must be puttied. The easiest way to do this is using automotive putty. After filling, sand the treated surfaces, then repeat step 4 - clean the surface with a damp cloth.

Step_7 Priming. Coat the chipboard with one or two layers of primer, this will achieve better adhesion of the paint to the surface and reduce paint consumption during further painting. It is best to use an aerosol acrylic primer. After priming, wait for the primer to dry completely.

Step_8 Finally we got to the most creative and interesting moment - COLORING!

What paint to paint chipboard at home?

For painting chipboard, enamel paints and varnishes are used. Varnishes are used to give the painted surface a deeper and beautiful color, and, most importantly, to protect the painted surface from damage and abrasion during operation. The range of paints today is quite wide: oil, alkyd, acrylic, epoxy. We recommend using acrylic paints, preferably aerosol ones, for painting chipboard at home, and there are a number of reasons for this:

1 Acrylic paints today are offered in very large assortment colors and shades. There are hundreds of them, in addition, there are acrylic paints with special effects: metallic, fluorescent, hammer, pearlescent, etc.

2 Easy to use, application does not require special skills, even a beginner can handle it.

3 Aerosol acrylic paints evenly cover the surface and create a perfectly even and smooth finish.

4 Non-toxic, dry at room temperature for 20-25 minutes, which is very important.

5 They have good adhesion to almost any material, including chipboard.

6 Durable. Subject to the staining technology, they stay on the surface for many years.

So, we have chosen the paint. A few words directly about the staining process:

If you are using spray paints, shake the can well for 20-30 seconds first to mix the paint well. Apply the paint from a distance of 20 - 25 cm with wide, even strokes. If possible, lay the chipboard surfaces horizontally to avoid streaks. If the surface is located vertically - paint with movements from top to bottom. Apply at least 2 coats of paint (preferably 3 coats), while waiting for the previous coat to dry completely (20 - 30 minutes) before applying the next coat. When painting, pay special attention to the joints, inside corners and other hard to reach items.

Step_9 Varnishing. After your chipboard product is painted and the paint has dried, we recommend applying 1-2 coats of varnish. As we said above, this will give the surface a more beautiful deep color and protect it from damage and wear during operation. If you used acrylic paint for painting, we recommend that you use acrylic lacquer, glossy is best, but matte is also possible - depending on what kind of product you are painting and on what you yourself like best.

In painting chipboard, as well as when working with other materials, there are secrets. Here are some tips that are sure to help you get the job done quickly, save money, and get better results when painting chipboard at home:

a For painting chipboard c dark color pre-coat the surface with at least two layers of primer.

b Before painting chipboard. treat the surface with deep penetration impregnation - this will make your product much more durable

d Remember to cover surfaces that do not require painting, masking tape and cover film. This will save you from mistakes and help keep the surface from getting paint on places that do not require coating or have already been painted.

e If you are painting with ordinary paint, have brushes of different thicknesses in your arsenal.

e A short pile roller will help achieve more smooth surface, and with the help of a roller with long pile texture can be achieved.

w Play with color palette to create a unique style. Correctly similar colors will help to increase or vice versa to narrow the space where necessary.

h Majority modern paints and varnishes are non-toxic, however, thorough ventilation of the room and use protective mask and a respirator at home will not interfere.

The transformation of furniture, floors, walls and other surfaces made of chipboard with the help of staining is great idea, both for complete and partial changes in the interior of a house, cottage, workspace. As you probably already understood, in order to paint the traffic police with your own hands, no colossal investments of effort and money will be required - everyone can do such a transformation.
Experiment with colors, because it is quite possible that you will even discover the talent of a designer capable of creating unique and inimitable items that cannot be found anywhere else. Updated furniture made of chipboard after painting can become a reflection of your way of thinking and individual vision of the world. Good luck with your next masterpiece!

If this article was useful to you, please rate it (at the top of the page). Thank you!

Visitors to this page most often choose in the online store:

http://www.samokraska.ru