After a heavy labor day on earth, sometimes you want to cleanse your body of dirt and refresh yourself in warm water.

If there is a body of water suitable for swimming nearby, then it’s good. And if not, then it's time to think about arranging a summer shower in a summer cottage.

What you need to know about the summer shower

There are two types of this building:

• Naturally heated by sunlight. This shower is simpler in design. But it will not work on cloudy and cold days.
• With artificial heating. In this case, you need to think about the type heating device and take care of its proper design. But such a shower will not depend on the vagaries of the weather.

A shower cabin with a tank can be purchased at the store. Its cost varies from 5,000 to 18,000 thousand rubles, depending on the materials.

Such a shower will last much longer and the water in it will heat up faster and hold heat more reliably. A tank is more suitable for a shower design square shape. It is more stable and roomy.

In addition, this form accelerates the heating of water. The size of the tank depends on the number of people who will use it during the day. But remember, the larger the tank, the slower the water warms up in it.

Now consider the stages of preparation and construction of a summer shower with heated water.

Preparatory work

It all starts with choosing a place where the shower will stand. It should be protected from the wind and as accessible as possible to the sun's rays.

The first condition is necessary to prevent the possibility of catching a cold due to a draft after taking a shower.

The second is to make water heating more efficient. Even if you are designing an artificially heated shower, a natural one will help reduce energy consumption. And an important factor - it is better to put a shower near a reservoir or a water tap.

Having decided on the place, it's time to think about the size of the structure. The standard is a square-shaped shower with walls one and a half meters long and a little more than two meters high. But if among the potential users of the soul there are full or very tall people, in the design of the cabin you need to take this into account.

An important factor is what materials will be used in the construction. You can use a frame made of wooden beams. It is eco-friendly, but not very durable.

Therefore, the shower frame is preferred to be made of metal, and everything else is made of wood. In this case, you should prepare tool kits for working with both metal and wood.

The last point that needs to be considered before starting construction is the drain device. There are several options. The simplest is that the water goes into the soil under the booth.

This is not very convenient, because you have to leave gaps between the boards in the floor, and this in turn will lead to drafts in the shower. A more common option is to drain water into a specially dug cesspool or septic.

To do this, a tray is installed on the floor of the shower stall. It is specially placed with a slope so that the used water does not stagnate and does not require additional efforts to clean up after taking a shower, and a pipe or hose is brought from below, the other end of which is sent to the pit.

Building a summer shower

Construction starts with installation uprights. If the soil in your area suburban area does not differ in reliability, then it makes sense to build a foundation under each rack.

frame three walls can be strengthened with cross beams. So you can be sure that the structure will not fall apart in a couple of years under the weight of a tank or something else. And on top you need to equip a platform for a tank of water.

Sheathing is carried out with already prepared material in two layers (external and internal), between which insulation is optionally laid.

This extra layer is necessary if you plan to use the shower in spring or autumn when the weather is not warm enough. After completing this part of the work, the door is hung.

In conclusion, the installation of the tank is to be done. First, a heating element (heater) is installed inside on metal brackets, and so that it does not touch the walls. Then a hose equipped with a water tap is connected to the tank, and an electric cable is connected to the heating element.

All this should now be installed on a prepared platform on the roof and secured with metal cables. From above, you can build a semblance of a greenhouse: stretch the film (preferably dark color) on wooden bars.

So the heat will be attracted and at the same time not go outside. At the final stage, it is worth once again checking the tightness of the system, if necessary, use rubber gaskets or silicone seals.

With limited time or funds, you can arrange an endowed version of the shower. He settles against the wall country house, to which a water tank and a shower head are attached. The walls of the shower room are replaced in this case with curtains made of tarpaulin or cellophane, attached to a light wooden frame.

The dacha always combines a place of both work and rest. Therefore, make sure that the working conditions are comfortable, and the place of rest is pleasant. A summer heated shower will help you with this.

Photo ideas for a summer shower at their summer cottage

The construction of a summer shower for a summer residence is not complete without questions related to the choice of material and the determination of the size of the structure. In addition, I want the building to be heated. This will make it possible to swim on cold days when the water in the tank does not have time to warm up from the sun. important question is the organization of drainage and drainage dirty water. Today we will look at how to build a summer shower with our own hands, and we will try to address all the questions of interest.

A country shower is so simple that it does not require a detailed diagram. Usually withstand standard sizes booths 1000x1000x2200 mm. It is impossible to build a cabin below, since it will take part of the height wooden pallet, plus a watering can over your head. But the width and depth of the structure, it is desirable to individually select the physique of the owners. For example, an obese person in a small booth will be cramped, so the dimensions will have to be increased.

Drawing of a simple summer shower for a summer residence

If you decide to cultivate the building, build a dressing room with a dressing room, install benches and a table in it, drawings will already be needed here. Draw what you want to build, specify all dimensions. Composing detailed diagram Please consider the following points:

Wooden shower cubicle

Building a cabin out of wood is the most common option due to its ease of construction. Wood - ecologically pure material, easy to process. Its only drawback is susceptibility to moisture and bugs, so it requires additional processing. To build wooden shower to give, you will need boards and timber, preferably from trees conifers. You can, of course, use oak or larch. The material made from these types of wood is more durable, but it is more difficult to process. Having decided on the material, get to work:

Variants of wooden cabins for a summer shower

Polycarbonate cabin

It is easier to build a polycarbonate booth than a wooden one, but you will need welding experience. The fact is that for polycarbonate it is necessary to weld a frame from a metal profile. For racks, a profile with a section of 40x60 mm will go, and a smaller section can be used for strapping. The use of a wooden frame for polycarbonate is not desirable, since both materials tend to "play" from changes weather conditions. From this, polycarbonate sheets can be deformed.

The process of manufacturing a metal frame for polycarbonate is similar wooden structure. Concrete the main racks, and then weld the upper and lower jumpers. Three jumpers must be made in the middle of the frame so that the polycarbonate sheets do not sag. The fourth is not needed. She will interfere with the doors. From above, weld the frame under the tank. Make a frame for the door from a profile with a section of 20x20 mm and fix it with hinges to the rack. Paint the entire structure with waterproof paint.

For sheathing, use opaque polycarbonate honeycomb sheets, 6-10 mm thick. big leaf cut into fragments according to the size of the booth circular saw. Fix the resulting polycarbonate plates to the frame with self-tapping screws with a thermal washer. The door is also sheathed with a sheet of polycarbonate. Bolt the handle and latch to the frame.

Polycarbonate shower option with dressing room

Shower tank

Cabin made of corrugated board

A good option for giving would be to build a cabin from corrugated board. Lightweight, durable and durable material will serve long years. For a metal profile, both metal and wooden frame, but always with additional cross bars. Sheets of corrugated board are soft, and additional emphasis will not interfere with them. We build any of the frames for the metal profile in the same way as the above options. In any case, weld the door frame from a metal profile.

Fastening the corrugated board is done with galvanized self-tapping screws with a sealing washer through one wave. First fix the sheets of corrugated board on the side walls, then sheathe the door. If you need to cut the material, use scissors or a special disc with teeth on the grinder so as not to burn when cutting polymer coating corrugated board.

Cabin made of bricks

The construction of a brick cabin in the country requires the construction of a foundation. To do this, it is enough to dig a trench 200 mm wide and 400 mm deep along the perimeter of the future structure. Fill the trench with bricks and pour liquid concrete to seep through between them. A week after the concrete has hardened, start laying bricks on cement mortar. Don't forget to install a box for the door. The door itself can be made of wood or a frame can be welded from a profile and sewn up with a sheet of corrugated board. On the last masonry, wall in across the building wooden bars, preferably the thickness of the brick. They will lay the roof and fix the tank.

Installing the roof and tank

The material for the roof will need to be hard. Slate or corrugated board is well suited. Having secured roofing material, drill a hole in the center of the roof. Place the tank on top so that the water supply tube passes through the hole. Screw the tap and watering can onto the tube.

Optimum tank capacity for country shower- 200 l. In the store you can buy a plastic or galvanized tank or make it yourself by welding from stainless steel. Any container with a neck for pouring water will serve as a tank. To make a shower for a cottage with heated water, mount a heating element with a power of 2 kW in a metal tank. Paint the top with black paint. Dark color attracts Sun rays and the water will heat up faster.

Scheme of the device of the tank for a summer shower with heating

If you install wood-burning titanium in a cabin in the country house, then in addition to hot water, you will get a heated room. Then you will need to install a second tank with cold water next to it.

Arrangement of the floor and drainage

The floor and drainage of the shower for giving can be done in two ways:

Summer shower in a country house

In the presence of free space, country shower can be built in the house. To do this, it is better to purchase a shower stall in the store. AT concrete floor make a hole and install acrylic pallet according to the product instructions. Connect the siphon on the pallet corrugated hose to the sewer. Seal the joints of the pallet to the floor with sealant. Next, according to the instructions, assemble the frame from the profile, install the doors, bring the cold and hot water from the boiler.

As you can see, you can build a summer shower with your own hands in the country from almost any material. The main thing is to prepare drawings, material, tools and show aspiration.

In contact with

Country house for many, it is a favorite place where you can relax from the bustle of the city. But here, far from civilization, people are not used to giving up the benefits that this civilization provides. And one of them is the opportunity to splash around on a hot afternoon. under a cold shower. So Summer shower refers to household facilities necessary for a comfortable pastime on suburban area. It is especially relevant if there is no natural reservoir nearby. In order to feel like a person in the country, it is necessary to build a solid structure that can last more than one season. Have you thought about how to build Summer shower? Photos will clearly demonstrate the main stages of the process.

We build a summer shower for a summer residence with our own hands

Start realizing your idea with careful design. As they say, measure seven times, cut only once. To get started, view finished projects summer shower and make your own based on them. Take into account the place allotted for the shower, the availability of building materials and the desired dimensions. Here you need to take into account the volumes of the owners themselves.

Even a beginner can easily draw up a shower project on their own. A simple drawing or a small drawing will help you calculate the amount of building materials, avoid some mistakes and unnecessary costs.

Summer shower should be spacious and comfortable. It is necessary to provide a place for clothes and bath accessories - at least 40-60 cm. The height of the shower should be about 2.50 m. The most common indoor dimensions are 160x100 mm and 190x140 mm. All this must be taken into account when drawing up a drawing or project.

Site Preparation Tips…

Now you need to decide on the location of the summer shower. Naturally, it is better to build it in a well-lit sunny place away from other buildings. Then the water in the tank will be heated throughout the day from solar heat. But if it is planned to build a heated summer shower, then it is not necessary to adhere to this condition.

The distance from the house should also not be too great so that you can quickly go after water procedures into the room. It would be wise to take care of the water flow in advance. It is better to take it to a septic tank or a septic tank. It is worth paying attention to the convenience of water supply and, if possible, ensure automatic filling of the container. After choosing a place, it is necessary to prepare the site: remove upper layer, level the base under the shower and fill the area with sand.

Rebuilding the frame...

An outdoor shower can be a capital structure, or maybe light frame design. Therefore, the main stages of the construction of such souls differ.

The foundation is a reliable basis for a shower cabin, but sometimes it is completely useless

To make the base for the shower correct and for convenience, you need to make elementary markings: for this, pegs are hammered in the outer corners of the site. After that, be sure to check the diagonal and pull the cord.

The dimensions of the foundation depend on the materials that will be used in the construction of the shower. For a brick or cinder block building, a foundation is poured 30 cm deep. If a metal or wooden frame for a summer shower is used as the base, the foundation will be somewhat different. Before pouring, you need to prepare a place for pipes - lay a log or branch desired diameter wrapped with ruberoid.

If you use an outdoor shower the family has been planning for more than one year, it is better to make formwork - to raise the level of the foundation above the ground by 10-15 cm, increasing the height of the trench due to boards reinforced with pegs and spacers.

When pouring the base under the shower with concrete, it is extremely important to ensure flat surface. This is done in the same way as with floor screed, using a level and two guides. The guides are leveled, poured with concrete, the floor base is leveled along the guides. Only horizontal surface can serve solid foundation for further building. After leveling is done, start laying bricks.

Installing a shower using a frame

A metal frame can be used as the basis for the shower (it is more durable). Building a summer shower will be much more economical if you use wood. But this material is not durable. Considering the peculiarities of our climate and high humidity due to the operation of the building, it is better to treat it with bio-impregnation to protect it from insects and fungus.

Determining the amount of building materials and the size of the building, proceed to the installation of the frame. The first stage is markup. On the ground, a rectangle is designated, the sides of which will correspond to the parameters future design. In order for the design of the summer shower to be stable, it is necessary to make pile foundation. Therefore, holes of the required depth are drilled at the corners of the marking (130-170 cm, the depth depends on the length of the pipes). Then the foundation is directly installed from the pipes. It's better to use it metal pipes 1.5–2 m long (9–10 cm in diameter), but even railway sleepers can be used. The piles are deepened into the ground so that they protrude 20 cm beyond the soil. The pipes are then filled with concrete. After it hardens, wooden bars should be installed in the pipes. The width of the beam used for the frame should be no more than 10 cm.

This is how we cover the frame with pvc film and get an excellent building

The next installation step is ligation: starting from the top, the entire structure is bolted together. If the calculation is made correctly and all dimensions are observed correctly, the design will turn out to be reliable. This will make it possible to install a water tank big size. Its volume should be calculated according to the formula: 40 l × 1 person and not more than 200 l. Heavy capacity construction may simply not withstand. It is desirable that the tank be flat and correspond to the roof area, that is, rest against the supporting structures.

The dressing inside the frame will later serve as lags for the shower floor. Now we connect the beams-bases of the walls with each other with slopes. They should be installed exactly in the thickness of the wall, but not in the overlay.

And here is the option sheathed with plastic slate

As walls for such a shower, slate sheets, OSB boards, boards, plastic panels and even PVC film.

Making communications...

You can build a summer shower with your own hands from building materials, remaining on the site after the construction of the dacha, but with the summing up of communications, the situation is somewhat different. Here you can not do without financial investments.

• Pipe laying, tank installation. After the erection of the structure, it is mounted water pipe. The outlet for the shower head hose must be made above the level of the head. Otherwise the pressure will be too low. Now you need to put the tank. Purchased can be installed plastic tank. Although, in order to save money, a barrel or any other container is usually used. Before the tank rises, you need to make a tap with a thread, and also install a tap with a nozzle. Now the tank or barrel should be securely fastened to the roof. As a rule, water in a tub or tank is heated with the help of sunlight. In order for the tank to heat up faster, it is pre-painted black. It is good to equip a film greenhouse around the tank: cover it with foil to reduce heat transfer from the north side.

A metal shower tank will never go out of style, but now plastic options are increasingly being used.

• Lighting. When wiring wiring for lighting, do not forget about the rules of electrical installation. After all, the humidity in the shower is increased. Of course, you can do without electric lighting if you use the shower exclusively in summer time. A stream of light coming from a small window (above head level) with frosted glass will also be enough. In spring, the days are somewhat shorter, so only daylight will not be enough.
• Ventilation. To improve the circulation of air flows and protect against the appearance of condensate, it is advisable to make a hole in the ceiling and close it with a decorative grille.
• Shower drain. How to build an outdoor shower, make piping, bring lighting - we figured it out. Now let's deal with the drain problem. With an increase in the average daily temperature, the volume of work of summer residents increases significantly and the load on the shower increases. That's just the temperature of the soil does not affect its drainage properties. It is good if it is possible to combine the drain from the shower and the sewer at home.

For quick disposal and good drainage of wastewater, an outdoor shower must be installed on a hill. The walls of the pit should be further strengthened to prevent shedding. Please note that the volume drain pit must certainly be at least 2 cu. meters.

A common mistake of novice builders is the location of the septic tank near the wall of the shower stall or under the shower itself. If the volumes of water are large, then the septic tank can be flooded. Over time, drainage works worse, appears bad smell. With constant heating, not only soil shrinkage is possible, but even the destruction of the foundation, which is extremely dangerous. Therefore, the drain of the summer shower must be diverted a few meters from the structure.

The water drain is equipped with a waterproof layer using PVC film, roofing material or hydrostekloizol. Alternatively, do concrete screed reinforced with metal mesh.

It is impossible to use clay as a waterproof layer. After a while, it will wash out and may contaminate the drainage ditch.

We install the pallet

To equip a summer shower with your own hands and provide an outflow of wastewater for it will allow the pallet. It can be a purchased pallet, a stainless steel sheet pallet, or the most cheap option- wooden pallet. Instead of a pallet, boards are laid, but not tightly, but leaving gaps for water. The grate of boards is pre-sanded well with sandpaper and treated with an antiseptic. For convenience, you can put a rubber mat on top.

The simplest shower tray - from ordinary boards

Waterproofing must be laid between the floor of the summer shower and the tray. For this, ruberoid is used. When installing the pallet, it is necessary to ensure that the slope is formed towards the drain for unhindered water flow. The pallet is screwed to the walls with self-tapping screws.

For more comfortable washing, so that you do not have to stand on metal pallet, it is desirable to put plastic gratings.

Building cladding…

An outdoor shower should harmoniously fit into overall design your yard. Any designer will tell you that for outdoor upholstery it is better to use materials that complement the ensemble of adjacent buildings.

Facing the summer shower is not only decorative, it is necessary to protect the walls from the effects of weather. The surface of the walls can be plastered and painted or sheathed vinyl siding, it all depends on the imagination of the owner, his financial capabilities and features of the structure. For example, a polycarbonate outdoor shower on a frame does not need to be lined at all.

Left - polycarbonate variant; on the right - a shower lined with wood

A good option is to sew up the walls and ceiling with clapboard. If the family will visit the dacha only in the warm season, then it is better to choose pvc film, dense colored (opaque) polyethylene or tarpaulin. If the shower cover is removable, it can be easily removed in the pantry for the winter.

How to make an outdoor shower comfortable...

It is very convenient when the building is divided into two zones: a shower room and a dressing room. To prevent water from entering the dressing room area, the floor of this area should be made a few centimeters higher. To protect clothes from splashes will help and a small decorative curtain from polyethylene.

If you need to use the shower even in a colder period of time, then the walls will have to be insulated. For this, polystyrene foam is used. This material must be filled inner space frame. Further, the structure is upholstered with PVC film using a stapler and decorative rails. Already on top of the film produce interior decoration.

If you choose materials to decorate an outdoor shower (there are plenty of photos on the Internet and in catalogs), try to pay attention not only to aesthetic data, but also to practicality. Only moisture-resistant materials are suitable for finishing the inside of the shower cabin.

A modern outdoor shower in the form of an extension to the house - why not an option?

For interior decoration you can use thin linoleum, plastic panels, oilcloth or wood. If you decide on wood, then do not forget to cover each board separately with hot drying oil, and only then proceed to finishing work. When facing internal walls the material is launched under the sides of the pallet.

To improve soil drainage, you can plant a few moisture-loving plants next to the shower. Green spaces absorb water. They not only decorate, but also protect the space around the shower from waterlogging.

Thus, a do-it-yourself summer shower will become an indispensable outbuilding on personal plot.

Foreword

When finishing a summer shower, performing outdoor work, it is important to choose a material that is resistant to precipitation.

Required Tools and materials

clapboardRollerNailsPrimerplaned boardDrillTile groutA rockPencilBrushKleimerPlaster ladlecuvetteLighthousewood stainknifeTiletile cutterPoluterokRoulettesquareExtensionLevelplaster mixturescrewdriver

Expand

Content

When finishing a summer shower, performing outdoor work, it is important to choose a material that is resistant to precipitation. It is also desirable that exterior finish well combined with others dacha buildings. When finishing the shower in the country house, the same materials are used inside as for the showers located in the house. Among the leading - and traditional tiles.

How can I finish the shower inside

In order not to disturb the interior of the summer cottage, it is recommended to arrange a booth for a summer shower in uniform style with other garden buildings. Any material can be used for outdoor upholstery: moisture-resistant plywood, fiberboard, plastic or etc.

It is desirable to insulate the cabin using polystyrene foam. They need to fill the entire space of the frame. Styrofoam padding needs to be upholstered plastic wrap using construction stapler. On top of the film, interior decoration can be performed.

Trim interior spaces country shower can be, very convenient to operate. They are capable of protecting wooden details from decay.

Recently, materials with waterproof properties, such as PVC film, oilcloth or linoleum, have been especially popular when decorating a shower in a country house. These materials can be fixed with rails covered with a protective layer of varnish.

The wooden parts of the shower cubicle should be carefully treated with drying oil and then painted. Thanks to this, it is possible to extend the life of the entire structure. It is not advisable to paint wooden walls inside the cabin.

These photos of the decoration of the summer shower inside show the whole variety of modern finishing materials:

Summer shower tiles

The most practical material for interior wall decoration in a summer shower cabin is tile. It must be laid out to a level exceeding human height by 40-60 cm. This is necessary so that the upper boundary between the tile and the wall is less exposed to the negative effects of moisture. Tiles can be glued to walls using a special tile adhesive, but are often placed on cement mortar.

Before tiling the inside of the shower, the adhesive must be diluted with water before laying in the proportion indicated on its packaging. Immediately all the glue should not be diluted, it is better to do this as the tiles are laid. It is best to start facing from the bottom of the wall. To prepare a cement mortar, it is necessary to mix 1 part of M 500 cement and 4 parts of clean sifted sand. Then you should add water to the consistency of thick sour cream.

The procedure for using mortar and tile adhesive is the same. Using a special notched trowel, apply glue or cement mortar to the tile, and then firmly press the tile to the wall surface. When finishing with shower tiles, it is necessary that a soft rag is always at hand to remove excess glue or protruding from under the tile. The remains of the tiles can be used for lining the concrete or brick floor of the shower stall. It should be remembered that there is a need for a high threshold between the washing compartment of the summer shower and the locker room so that water does not flow into it.

During wall cladding tiles you can drill holes for further installation of shelves for shower accessories, as well as install a rod for a curtain that separates the washing compartment from the dressing room. In the locker room, it is recommended to make hooks for clothes and hang a mirror if the area allows.

Wall decoration in the shower outside

After erecting a brick summer shower to finish the walls on the outside, their walls can be plastered. It is recommended to start plastering from the top. For this small plot you need to moisten with water and, using a grater, carefully apply first a less thick layer of the solution, and then a thicker one.

The thickness of each of the layers should not exceed 5 mm. It is necessary to apply plaster evenly over the entire surface, otherwise it will not dry at the same time, and the layer will be heterogeneous.

After a few minutes, in a circular motion of the grater, it is necessary to grout the plastered surface until it becomes even and smooth. If the solution has already hardened and will not rub well, then it must be moistened with water, sprinkling the surface with a matting brush. This process must be repeated in the same sequence until the work is completed.

Plastering the corners of the walls must be done with the help of a wooden lath attached to them. Approximately 7-10 minutes after applying the solution, the rail must be carefully removed, correct the angle and wipe.

Here you can see a photo of the finish of the shower inside and out:

Water treatments in the open air are very useful, so many adherents of relaxation and hardening decide to make a summer shower for a shower in the country with their own hands, or at least install a finished booth on the site. This article will help you understand the design features, choose the right size and installation location, draw up a preliminary diagram and complete all stages of construction without errors.

Types of autonomous toilets. Choosing a place for building a toilet in a summer cottage

If it is planned to build a capital shower for a do-it-yourself brick cottage, it is advisable to use belt type foundation. A trench is formed along the perimeter of the future building. Optimal depth is 0.5 m. Next, the formwork is installed. At the bottom of the trench, it is necessary to form a sand and gravel cushion with a thickness of 0.1 m. After that, reinforcement is laid and concrete is poured. This must be done in such a way that ready-made the foundation rose above ground level by about 0.1 m.

When the base is completely hardened and dry, it will be possible to begin the construction of the sewer system.

How to organize a drain system in the shower in the country with your own hands

There are several ways to organize a waste system in a shower stall. The choice of construction technology depends on several factors:

• type of soil on the site;
• type of foundation;
• the number of people living in the house.

If as a foundation for a summer shower in the country house is used monolithic slab, then before filling it is necessary to lay the system plastic pipes with knee. The plate is formed in such a way that there is a slope to the side on all sides drain hole. Sewage pipe is displayed outside the shower room and connected to a common drain system. You can bring the drainage to the drainage well.

Helpful advice! For the construction of a similar sewer for a booth installed on a foundation of a different type, it is not necessary to fill the floors with concrete. It is enough to buy a summer shower for giving with a pallet made of acrylic. This element will serve as the floor.

With connection to sewer system – best option for big family, since the pit will not be able to accommodate the volume of wastewater that will be formed during operation. If the design is designed for 1-2 people, it will be enough to drain directly under the booth. But this type of system is suitable for areas with a loose type of soil, when the shower is installed on a columnar or pile foundation. This option can also be used on a tape base.

First you need to remove a layer of soil with a depth of 0.5 m. The formed depression is filled with gravel or stone to half its height. The rest is covered with crushed stone with a fine fraction. After the cabin structure is assembled, a pallet made in the form of wooden lattice. The system is designed in such a way that wastewater passed through the drainage layers and gradually soaked into the soil.

Sometimes the owners summer cottages lead the sewer into the garden, which cannot be called good decision. If you still resort to a similar method, it is desirable that the place where the water drains is well warmed by the sun. Otherwise, the liquid will accumulate, and a swamp full of mosquitoes will form around the shower.

Making a cabin for a summer shower: photo and construction technology

For the construction of a cabin for makeshift shower any available materials can be used.

Suitable for these purposes:

• wood;
• polycarbonate;
• corrugated board;
• brick.

Each type of material has its own advantages, features and properties.

How to build a shower in the country with your own hands: economy cabin

There is a little trick that will help you achieve savings in the process of building a shower house. To reduce costs, it is enough to use one of the blank walls of the building as a side for a booth.

Before you build a budget type summer shower, you need to fix a water tank on the wall small size equipped with a watering can. Here you can also install elements related to comfort, for example, hooks for clothes, shelves, etc. In the upper part of the future structure is a partition. It is fixed on the wall of the building. As front door a tarpaulin or film (necessarily opaque) can be used. The curtain is suspended with rings.

The floor is arranged so that the drains are diverted as far as possible from the foundation part of the house. To do this, a platform is concreted or you can get by with installing a pallet made of acrylic.

Helpful advice! If use inner corner building that has L-shape, you can generally avoid the construction of the sides of the booth. Their function will be performed by the walls of the building.

Building a wooden cabin for a country shower with your own hands

The most common version of a country shower is a booth made in the form wooden house. This type of building is considered one of the most affordable. Wood is easy to process. At the same time, it perfectly retains heat, which is a definite advantage if the shower is to be used in cold weather.

To build a summer shower in a private house with your own hands, it is advisable to use wooden beam. For the manufacture of corner posts of the booth, a material with a section size of 10x10 cm is required. A tank for 200 liters of water is installed in the upper part of the shower, so the beam must be thick enough to withstand such a weight load.

To hang the door, you will need to install two additional racks in front of the booth. These elements are placed between the corner posts. For their manufacture, you can take a bar with a section size of 5x5 cm.

To form a small slope angle for pitched roof cabins, it is recommended to install the front corner posts 0.2 m higher than the rear ones. This is not required if a square-shaped tank is used as a container. In this case, the racks are mounted on the same level.

All supports are attached to wooden frame bottom harness. For fixing it is necessary to use hardware and metal corners. At the top of the structure, strapping is done in a similar way. You can use spacers to secure the racks more firmly. On the upper trim of the frame part of the booth, a basis for mounting the container is formed. In this case, you need to read not only the size, but also the shape of the tank.

For sheathing the frame part of the building, you can use a board 2 cm thick. This material is also suitable for making a door. It is necessary to lay the boards in one row and knock them together with the help of two jumpers. To prevent the door from skewing, the structure can be strengthened obliquely using a long rail. door frame for a country summer shower it is made of boards, the thickness of which is 4 cm. It is recommended to use self-tapping screws as fasteners.

When the booth is completely ready, it can be opened with a colored varnish composition. With inside the entrance is curtained with a film, otherwise the doors will swell from moisture.

Helpful advice! Often, a large barrel for a shower in the country is used for construction. By installing a watering can over the structure, you can get a budget option wooden cabin.

Polycarbonate garden shower technology

Since wood is subject to deformation changes under the influence of moisture, many site owners are thinking about how to make a shower in the country with their own hands from more practical and resistant materials, such as polycarbonate. The frame part of the cabin is made in the same way as in the case of a wooden shower, however, it is necessary to use metallic profile. Optimal size section - 4x6 cm.

The frame part of the cabin is formed with the help of racks and jumpers between them. In this case, are used metal elements, therefore, to fasten them, it will be necessary welding machine. Moreover, the assembly order can be performed in several ways. In the first case, the frame part is welded separately, after which it is installed on the base and fastened with anchor bolts. The second method involves concreting racks during the pouring of the foundation. Then the strapping is formed, spacers are attached.

It is desirable to use as a covering for a shower made of polycarbonate sheet material 1 cm thick. metal frame it is fixed with the help of hardware, which must necessarily have sealing gaskets.

Installation of the tank and features of the construction of a shower in a country house with heating by one's own hands

At the last stage of the construction of the shower, a tank is installed. The container can be made independently using any container made of of stainless steel or plastic. To do this, it is necessary to form a hole in the bottom, the diameter of which is 1.5 cm. A pipe segment with a thread on both sides is attached to it with the help of nuts. The length of this element should be 30 cm.

In the roof of the booth in the center, you need to make a hole where the pipe will be inserted. After installing the tank, a tap and a watering can made of plastic are screwed onto the free end. Then the container is firmly fixed on the frame of the frame part of the booth, filled with water and covered with a lid.

To create a summer shower with heating for a summer residence, it is enough to install a heating element in the tank. Of course, the natural energy of the sun can be used to heat water. In this case, there will be no electricity costs. However, the sun's rays are not able to heat a large volume of liquid. In addition, not every region has the necessary climatic conditions.

On the network you can find many schemes necessary for connecting a summer shower for a heated cottage to electricity. The advantage of these devices is that the water warms up in the tank quickly enough, regardless of the time of day and the weather outside. At the same time, a person can adjust temperature regime. If you attach a piece of foam to the hose, the most warm water. For the same reason, liquid is taken from the upper zone of the tank.

Helpful advice! To speed up the process of heating the liquid, you can add a coil to the circuit.

Is it possible to buy a summer shower for a summer residence inexpensively: prices for finished structures

To simplify the construction technology, you can buy a ready-made outdoor shower and install it on a prepared base. The cost of cabins is varied and depends on various factors.

The following points affect the price of products:

• material of manufacture;
• modification (presence of a locker room);
• the shape of the water tank (in the form of a barrel, a square tank);
• complete set (availability heating element, tank, temperature sensor, etc.);
• tank capacity;

• the material from which the water tank is made.

Average prices for finished structures

Name	price, rub.
Metal frame and PVC fabric
garden shower
Garden shower with water heater
Garden shower with water heater and dressing room
Polycarbonate construction
Cabin with 130 l tank
Cabin with 200 l tank
Cabin with 130 l tank with heating

A wide variety of materials suitable for construction, as well as manufacturing technologies, allows any summer resident to acquire a comfortable and convenient shower in the country. Moreover, you can make a booth yourself from improvised means or purchase it ready-made in a specialized store.